Abstract：Evaluating the electrical life of a high-voltage circuit breaker is important to ensure the safe and stable operation of power systems. However, the current life assessment mainly depends on the cumulative open-off current method and the dynamic resistance measurement method. The former is based on prediction and inference, which is inaccurate, while the latter cannot be used online. Therefore, based on a real 126 kV GIS device, this paper studies the method of electric life evaluation based on arc contact point analysis. After controlling the closing action of the circuit breaker, the control coil current, vibration, travel, and dynamic resistance signals are collected, and the signals are aligned. By marking the contact position between the arc contact and the main contact of the circuit breaker based on the characteristic points reflected on different signals, it is discovered that a high-frequency vibration signal is generated after the arc contact. According to variational mode decomposition (VMD) and short time Fourier transform (STFT), its frequency distribution is in the high-frequency range above 10 kHz and has strong independence. The dynamic resistance measurement on the contact shows that high-frequency vibration occurs after the arc contact, before the main contact, and moves with the arc contact. Therefore, high-frequency vibration characteristics are used to predict the contact position of the arc contact. The mechanism of this high-frequency vibration generation is studied. 3D modeling of the dynamic and static contacts is constructed, and COMSOL software is used for dynamic simulation. The measured travel curve is imported into the COMSOL simulation model to simulate the real motion state of the contact before and after contact. After the moving contact touches the static contact, the metal flap of the contact generates high-frequency signals with similar frequencies under friction and opening and closing knocking. By adjusting the position of the mechanism pull rod to change the contact rigid contact point, high- frequency characteristic vibration frequency is related to the contact rigid contact point. Furthermore, based on characteristic vibration frequency analysis, an online monitoring method is proposed for arc contact points. The inherent deviation between the position of the vibration characteristic frequency and the rigid junction point is measured through a calibration process. In the online situation, by detecting the position of vibration feature points and compensating for inherent offset, the position of the rigid joint can be derived. The results of the on-site porcelain column circuit breaker indicate that the maximum error of this method is about 0.905 mm, which is expected to achieve large-scale promotion and application in the online monitoring of high-voltage circuit breakers.
李辰辉, 褚继峰, 龙潇, 杨爱军, 袁欢, 荣命哲, 王小华. 基于弧触头接触振动特征分析的高压SF6断路器电寿命在线监测方法[J]. 电工技术学报, 2024, 39(15): 4883-4895.
Li Chenhui, Chu Jifeng, Long Xiao, Yang Aijun, Yuan Huan, Rong Mingzhe, Wang Xiaohua. Online Monitoring Method of Electrical Life of High Voltage SF6 Circuit Breaker Based on Analysis of Arcing Contact Vibration Characteristics. Transactions of China Electrotechnical Society, 2024, 39(15): 4883-4895.
[1] 贾磊, 蔡汉生, 胡上茂, 等. 500 kV串联电抗器对线路断路器开断能力的影响研究[J]. 南方电网技术, 2014, 8(6): 7-11. Jia Lei, Cai Hansheng, Hu Shangmao, et al.Study on influence of 500 kV series reactor on interrupting capability of line circuit breaker[J]. Southern Power System Technology, 2014, 8(6): 7-11. [2] da Souza R T, da Costa E G. Analysis of the correlation between the level of contact degradation and the dynamic resistance curve in circuit breakers[J]. Journal of Energy and Power Engineering, 2014, 8(6): 1104-1111. [3] 傅中, 陈维江, 李志兵, 等. 大容量电容器组用断路器弧触头侵蚀状态的评价方法[J]. 中国电机工程学报, 2016, 36(20): 5668-5677, 5744. Fu Zhong, Chen Weijiang, Li Zhibing, et al.Assessment method of arcing contacts erosion condition of circuit breakers used for large capacity capacitor banks[J]. Proceedings of the CSEE, 2016, 36(20): 5668-5677, 5744. [4] 张振乾, 王学军, 孙岗, 等. 特高压变电站大容量电容器组专用断路器电寿命试验研究[J]. 高压电器, 2014, 50(10): 1-8, 14. Zhang Zhenqian, Wang Xuejun, Sun Gang, et al.Study on electrical endurance test of circuit breaker specially used for switching high power capacitor banks in UHVAC substation[J]. High Voltage Apparatus, 2014, 50(10): 1-8, 14. [5] 马飞越, 黎炜, 王尧平, 等. 基于思维进化和L-M法优化BP神经网络的SF6断路器触头电寿命评估[J]. 高压电器, 2023, 59(3): 44-52, 60. Ma Feiyue, Li Wei, Wang Yaoping, et al.Electrical endurance assessment of contacts of SF6 circuit breaker based on MEA-LM-BP neural network[J]. High Voltage Apparatus, 2023, 59(3): 44-52, 60. [6] 关永刚, 杨元威, 钟建英, 等. 高压断路器机械故障诊断方法综述[J]. 高压电器, 2018, 54(7): 10-19. Guan Yonggang, Yang Yuanwei, Zhong Jianying, et al.Review on mechanical fault diagnosis methods for high-voltage circuit breakers[J]. High Voltage Apparatus, 2018, 54(7): 10-19. [7] Coll I, Casanovas A M, Vial L, et al.Chemical kinetics modelling of a decaying SF6 arc plasma in the presence of a solid organic insulator, copper, oxygen and water[J]. Journal of Physics D: Applied Physics, 2000, 33(3): 221-229. [8] 荣命哲, 杨飞. 电接触理论及应用[M]. 北京: 机械工业出版社, 2023. [9] 黎斌. 断路器电寿命的折算、限值及其在线监测技术[J]. 高压电器, 2005, 41(6): 428-433. Li Bin.Conversion, limit and on-line monitoring technology of electrical endurance for circuit breakers[J]. High Voltage Apparatus, 2005, 41(6): 428-433. [10] 何志鹏, 赵虎. 微型断路器电寿命评估[J]. 电工技术学报, 2022, 37(4): 1031-1040. He Zhipeng, Zhao Hu.Electrical lifespan evaluation of miniature circuit breakers[J]. Transactions of China Electrotechnical Society, 2022, 37(4): 1031-1040. [11] 蓝磊, 陈功, 文习山, 等. 基于动态电阻测量的SF6断路器触头烧蚀特性[J]. 高电压技术, 2016, 42(6): 1731-1738. Lan Lei, Chen Gong, Wen Xishan, et al.Erosion characteristics of SF6 circuit breaker contacts based on dynamic contact resistance measurement[J]. High Voltage Engineering, 2016, 42(6): 1731-1738. [12] 王振兴, 刁目鑫, 肖光宇, 等. 基于QPSO-SVR算法的SF6断路器触头烧蚀状态评估[J]. 高电压技术, 2023, 49(9): 3907-3917. Wang Zhenxing, Diao Muxin, Xiao Guangyu, et al.SF6 circuit breaker contact state assessment based on QPSO-SVR algorithm[J]. High Voltage Engineering, 2023, 49(9): 3907-3917. [13] 崔芮华, 张振, 佟德栓, 等. 基于改进经验小波变换多特征融合的航空交流串联电弧故障检测[J]. 电工技术学报, 2022, 37(12): 3148-3161. Cui Ruihua, Zhang Zhen, Tong Deshuan, et al.Aviation AC series arc fault detection based on improve empirical wavelet transform multi-feature fusion[J]. Transactions of China Electrotechnical Society, 2022, 37(12): 3148-3161. [14] 杨秋玉, 阮江军, 黄道春, 等. 基于振动信号时频图像识别的高压断路器分闸缓冲器状态评估[J]. 电工技术学报, 2019, 34(19): 4048-4057. Yang Qiuyu, Ruan Jiangjun, Huang Daochun, et al.Opening damper condition evaluation based on vibration time-frequency images for high-voltage circuit breakers[J]. Transactions of China Electrotechnical Society, 2019, 34(19): 4048-4057. [15] 邵阳, 武建文, 马速良, 等. 用于高压断路器机械故障诊断的AM-ReliefF特征选择下集成SVM方法[J]. 中国电机工程学报, 2021, 41(8): 2890-2901. Shao Yang, Wu Jianwen, Ma Suliang, et al.Integrated SVM method with AM-ReliefF feature selection for mechanical fault diagnosis of high voltage circuit breakers[J]. Proceedings of the CSEE, 2021, 41(8): 2890-2901. [16] 刘宝稳, 汤容川, 马钲洲, 等. 基于S变换D-SVM AlexNet模型的GIS机械故障诊断与试验分析[J]. 高电压技术, 2021, 47(7): 2526-2538. Liu Baowen, Tang Rongchuan, Ma Zhengzhou, et al.GIS mechanical fault diagnosis and test analysis based on S transform D-SVM AlexNet model[J]. High Voltage Engineering, 2021, 47(7): 2526-2538. [17] 高树国, 汲胜昌, 孟令明, 等. 基于在线监测系统与声振特征预测模型的高压并联电抗器运行状态评估方法[J]. 电工技术学报, 2022, 37(9): 2179-2189. Gao Shuguo, Ji Shengchang, Meng Lingming, et al.Operation state evaluation method of high-voltage shunt reactor based on on-line monitoring system and vibro-acoustic characteristic prediction model[J]. Transactions of China Electrotechnical Society, 2022, 37(9): 2179-2189. [18] 赵书涛, 许文杰, 刘会兰, 等. 基于振动信号谱形状熵特征的高压断路器操动状态辨识方法[J]. 电工技术学报, 2022, 37(9): 2170-2178. Zhao Shutao, Xu Wenjie, Liu Huilan, et al.Identification method for operation state of high voltage circuit breakers based on spectral shape entropy characteristics of vibration signals[J]. Transactions of China Electrotechnical Society, 2022, 37(9): 2170-2178. [19] 周进飞, 罗勇, 韩耀东. 12 kV真空断路器刚合点在线监测方法研究[J]. 高压电器, 2023, 59(9): 219-225. Zhou Jinfei, Luo Yong, Han Yaodong.Research on online monitoring method of the instant closing point of 12 kV vacuum circuit breaker[J]. High Voltage Apparatus, 2023, 59(9): 219-225. [20] 豆龙江, 何玉灵, 万书亭, 等. 基于振动信号的高压断路器弹簧疲劳程度检测方法[J]. 电工技术学报, 2022, 37(24): 6420-6430. Dou Longjiang, He Yuling, Wan Shuting, et al.Detecting method of high voltage circuit breaker spring fatigue based on vibration signal[J]. Transactions of China Electrotechnical Society, 2022, 37(24): 6420-6430. [21] 刘会兰, 许文杰, 赵书涛, 等. 面向高压断路器故障分类的电流-振动信号类聚几何敏感特征优选方法[J]. 电工技术学报, 2023, 38(1): 26-36. Liu Huilan, Xu Wenjie, Zhao Shutao, et al.Optimization method of clustering geometric sensitive features of current vibration signals for fault classification of high voltage circuit breakers[J]. Transactions of China Electrotechnical Society, 2023, 38(1): 26-36. [22] 刘会兰, 常庚垚, 赵书涛, 等. 溯源弹簧形变过程的断路器振动信号递归量化分析辨识方法[J]. 电工技术学报, 39(8): 2567-2577. Liu Huilan, Chang Gengyao, Zhao Shutao, et al.Circuit breaker state identification method based on tracing spring deformation process and recurrence quantitative analysis of vibration signals[J]. Transa- tions of China Electrotechnical Society, 39(8): 2567-2577. [23] 彭在兴, 王颂, 刘芹, 等. 高压断路器分合闸线圈电流采集实验平台与故障模拟实验研究[J]. 高压电器, 2018, 54(7): 248-253. Peng Zaixing, Wang Song, Liu Qin, et al.Experimental platform of high voltage circuit breaker’s opening/closing coil current acquisition and fault simulation experiment research[J]. High Voltage Apparatus, 2018, 54(7): 248-253. [24] 褚飞航, 黄虎, 彭在兴, 等. 252 kV断路器分合闸线圈在环境因素下的劣化规律研究[J]. 电力自动化设备, 2021, 41(2): 218-224. Chu Feihang, Huang Hu, Peng Zaixing, et al.Study on degradation of 252 kV circuit breaker’s opening/ closing coil under environmental factors[J]. Electric Power Automation Equipment, 2021, 41(2): 218-224. [25] 程亭婷, 高文胜, 赵宇明, 等. 高压SF6断路器动态回路电阻测量中的扰动现象[J]. 高电压技术, 2018, 44(11): 3604-3610. Cheng Tingting, Gao Wensheng, Zhao Yuming, et al.Fluctuation in dynamic contact resistance measurements for high voltage SF6 circuit breakers[J]. High Voltage Engineering, 2018, 44(11): 3604-3610. [26] 刘兆东. 高速断路器灭弧室熄弧特性及传动机构冲击动力学研究[D]. 沈阳: 沈阳工业大学, 2022. [27] 孙懿, 刘意杨, 宋纯贺, 等. 基于VMD和改进的FastICA算法的旋转机械故障信号分离方法研究[J]. 仪器仪表标准化与计量, 2021(1): 15-19. Sun Yi, Liu Yiyang, Song Chunhe, et al.Study on the separation method of rotating machinery fault signal based on VMD and improved FastICA algorithm[J]. Instrument Standardization & Metrology, 2021(1): 15-19. [28] Dragomiretskiy K, Zosso D.Variational mode decomposition[J]. IEEE Transactions on Signal Pro- cessing, 2014, 62(3): 531-544. [29] 孙尚鹏, 相中华, 吴强, 等. 弧触头烧蚀程度对灭弧室内短路开断过程多物理场的影响[J/OL]. 电测与仪表, 1-9 [2024-06-05]. http://kns.cnki.net/kcms/ detail/23.1202.TH.20230425.1058.004.html. Sun Shangpeng, Xiang Zhonghua, Wu Qiang, et al. Influence of arc contact ablation degree on multi- physical field of short-circuit breaking process in arc extinguishing chamber[J/OL]. Electrical Measurement & Instrumentation, 1-9 [2024-06-05]. http://kns.cnki.net/ kcms/detail/23.1202.TH.20230425.1058.004.html.
2024, Vol. 39 
