Abstract：During the electromagnetic launch process, the armature and rail are in an extreme multi-physical field environment. Due to rail vibration and uneven forces, the armature and rail generate ultra-high speed impact to form shear. However, melting and ablation caused by current result in the loss of the surface material characterization information. Therefore, it is difficult to carry out the mechanism of extreme multi-physical field on the material, which restricts the application of the material in the environment of ultra-high-speed impact and even electromagnetic launch. In order to address this problem, this paper designs the off-axis long bar with hoop specimen, and investigates the dynamic deformation characterization of 2A10 aluminum alloy under extreme multi-physical field environment, i.e., the current density of 108~109 A/m2 and the strain rate greater than or equal to 104/s. Comparing the distribution of microscopic features under different experiment conditions, and the effect of pulse current under the extreme multi-physical field conditions on dynamic deformation of the material is obtained. A pulse power supply and an electromagnetic repulsive device are adopted to equivalently simulate the extreme multi-physical field environment of electromagnetic launch. The electromagnetic repulsive device is used to generate a high strain rate in the specimen by generating an instantaneous (390 μs) Lorentz force. While the specimen is deformed at high speed, pulse current is injected at a suitable moment to realize the electro-thermal coupling. After the experiment, the specimens are axially cut, mechanical polished, and chemically etched. The microscopic features of the specimen profile are observed by optical microscope and scanning electron microscope. The simulation results show that the strain rate is the highest at the diagonal and in the middle, and the strain rate can be up to 2×104/s. Different deformation rates at different locations of the material profile, and the gradual decrease of the strain rate from the diagonal to the middle, may present different microscopic features. The strain distribution and strain rate distribution are basically the same. The shear stresses applied to the two points inside and outside the diagonal region are in opposite directions, thus forming shear in the diagonal region. The shear stress in the diagonal region is 3~4 times larger than that outside the region. Through the calculation of skinning depth, it is known that the pulse current is uniformly distributed in the long bar of the specimen, and the pulse current applied in the experiment satisfies the current density condition. The critical value of crack repulsion generated on the specimen surface is determined through several experiments, and this value is kept constant as the repulsion value. The experimental results of microscopic characterization of the specimen profile show that the adiabatic shear band can be clearly observed at the diagonal of the specimen profile without current, and cracks are generated at both diagonals, and the experimental observation results correspond to the simulation results. Selecting the appropriate moment to energize the pulse current, and the current densities were 3.68×108 A/m2 and 1.02×109 A/m2, respectively. The experimental results show that: (1) Under the same repulsive condition, the temperature gradient generated by the pulse current at the tip and both sides of the cracks healed the cracks. The crack lengths were reduced by 19.41% and 37.34%, respectively. (2) The pulse current suppressed the rotational dynamic recrystallization through the effects of electron wind and Joule heat, etc. The dynamic recrystallization grains were reduced and it was difficult to form the softening point inside the material, which suppressed the formation of adiabatic shear band. The lengths of adiabatic shear bands were reduced by 18.04% and 29.95%, respectively.
胡前程, 李伟昊, 李成成, 陈立, 李兴文. 脉冲电流对高速冲击下2A10铝绝热剪切带作用规律研究[J]. 电工技术学报, 2024, 39(19): 5937-5946.
Hu Qiancheng, Li Weihao, Li Chengcheng, Chen Li, Li Xingwen. Effect of Pulse Current on Adiabatic Shear Band of 2A10 Aluminum Alloy under High Speed Impact. Transactions of China Electrotechnical Society, 2024, 39(19): 5937-5946.
[1] 陈帅, 马偃亳, 赵婉瑜, 等. 电磁轨道炮最新研究进展及应用展望[J]. 科技创新与应用, 2022, 12(17): 11-14. Chen Shuai, Ma Yanbo, Zhao Wanyu, et al.Latest research progress and application prospect of electromagnetic rail gun[J]. Technology Innovation and Application, 2022, 12(17): 11-14. [2] 李军, 严萍, 袁伟群. 电磁轨道炮发射技术的发展与现状[J]. 高电压技术, 2014, 40(4): 1052-1064. Li Jun, Yan Ping, Yuan Weiqun.Electromagnetic gun technology and its development[J]. High Voltage Engineering, 2014, 40(4): 1052-1064. [3] 杜佩佩, 鲁军勇, 冯军红, 等. 电磁轨道发射器电磁结构耦合动态发射过程数值模拟[J]. 电工技术学报, 2020, 35(18): 3802-3810. Du Peipei, Lu Junyong, Feng Junhong, et al.Numerical simulation of dynamic launching process of electromagnetic rail launcher with electromagnetic and structural coupling[J]. Transactions of China Electrotechnical Society, 2020, 35(18): 3802-3810. [4] 马伟明, 肖飞, 聂世雄. 电磁发射系统中电力电子技术的应用与发展[J]. 电工技术学报, 2016, 31(19): 1-10. Ma Weiming, Xiao Fei, Nie Shixiong.Applications and development of power electronics in electromagnetic launch system[J]. Transactions of China Electrotechnical Society, 2016, 31(19): 1-10. [5] 马伟明, 鲁军勇. 电磁发射技术的研究现状与挑战[J]. 电工技术学报, 2023, 38(15): 3943-3959. Ma Weiming, Lu Junyong.Research progress and challenges of electromagnetic launch technology[J]. Transactions of China Electrotechnical Society, 2023, 38(15): 3943-3959. [6] 刘赛男, 孙洋洋, 翟鹏远, 等. 电磁轨道炮铜合金导轨失效研究与应对策略[J]. 兵器装备工程学报, 2022, 43(8): 87-94. Liu Sainan, Sun Yangyang, Zhai Pengyuan, et al.Research on failure mechanism and response strategy of copper alloy guideway of electromagnetic rail gun[J]. Journal of Ordnance Equipment Engineering, 2022, 43(8): 87-94. [7] 李建国, 豆清波, 索涛. 金属材料绝热剪切带形成机制及多尺度模拟研究进展[J]. 科学通报, 2021, 66(32): 4081-4097. Li Jianguo, Dou Qingbo, Suo Tao.Advances in formation mechanisms and multiscale simulations of adiabatic shear bands in metallic materials[J]. Chinese Science Bulletin, 2021, 66(32): 4081-4097. [8] Okada A, Kiritani M.Application of an electromagnetic accelerator to ultra-high-speed plastic deformation experiments[J]. Radiation Effects and Defects in Solids, 2002, 157(1/2): 157-164. [9] 张静, 谭成文, 刘新芹, 等. Ti-6Al-4V合金绝热剪切带的演化[J]. 稀有金属, 2009, 33(5): 648-651. Zhang Jing, Tan Chengwen, Liu Xinqin, et al.Evolution of adiabatic shear bands in typical microstructure of Ti-6Al-4V alloy[J]. Chinese Journal of Rare Metals, 2009, 33(5): 648-651. [10] Li Dahe, Yang Yang, Xu Tiancheng, et al.Observation of the microstructure in the adiabatic shear band of 7075 aluminum alloy[J]. Materials Science and Engineering: A, 2010, 527(15): 3529-3535. [11] Yang Yang, Jiang Feng, Zhou B M, et al.Microstructural characterization and evolution mechanism of adiabatic shear band in a near beta-Ti alloy[J]. Materials Science and Engineering: A, 2011, 528(6): 2787-2794. [12] Dimitrov N K, Liu Yucheng, Horstemeyer M F.Electroplasticity: a review of mechanisms in electro-mechanical coupling of ductile metals[J]. Mechanics of Advanced Materials and Structures, 2022, 29(5): 705-716. [13] Salandro W A, Bunget C, Mears L.Modeling and quantification of the electroplastic effect when bending stainless steel sheet metal[C]//ASME 2010 International Manufacturing Science and Engineering Conference, Erie, Pennsylvania, USA, 2010, 1: 581-590. [14] Sánchez Egea A J, González Rojas H A, Celentano D J, et al. Electroplasticity-assisted bottom bending process[J]. Journal of Materials Processing Technology, 2014, 214(11): 2261-2267. [15] Li Xia’nan, Xu Zhutian, Guo Ping, et al.Electroplasticity mechanism study based on dislocation behavior of Al6061 in tensile process[J]. Journal of Alloys and Compounds, 2022, 910: 164890. [16] 熊奇, 朱鑫辉, 赵翔, 等. AZ31镁合金管件电磁吸引式成形动态特性研究[J]. 电工技术学报, 2023, 38(10): 2577-2588, 2636. Xiong Qi, Zhu Xinhui, Zhao Xiang, et al.Research of dynamic characteristics in electromagnetic attraction forming of AZ31 magnesium alloy tube[J]. Transactions of China Electrotechnical Society, 2023, 38(10): 2577-2588, 2636. [17] 邱立, 余一杰, 聂小鹏, 等. 管件电磁胀形过程中的材料变形性能问题与电磁力加载方案[J]. 电工技术学报, 2019, 34(2): 212-218. Qiu Li, Yu Yijie, Nie Xiaopeng, et al.Study on material deformation performance and electromagnetic force loading in electromagnetic tube expansion process[J]. Transactions of China Electrotechnical Society, 2019, 34(2): 212-218. [18] 王忠金, 宋辉, 蔡舒鹏, 等. 脉冲电流诱导钛合金板材裂纹愈合与组织演变研究进展[J]. 塑性工程学报, 2019, 26(2): 1-14. Wang Zhongjin, Song Hui, Cai Shupeng, et al.Research advancements on self-healing of cracks and evolution of microstructures of titanium alloy sheets induced by electropulsing[J]. Journal of Plasticity Engineering, 2019, 26(2): 1-14. [19] Hines J A, Vecchio K S.Recrystallization kinetics within adiabatic shear bands[J]. Acta Materialia, 1997, 45(2): 635-649. [20] Chen Wei, Zhang Huan, Mu Juan, et al.Effects of microstructure and strain rate on dynamic mechanical properties and adiabatic shear band of TC4 alloy[J]. Acta Metallurgica Sinica, 2022, 58(10): 1-13. [21] Eskandari M, Mohtadi-Bonab M A, Zarei-Hanzaki A, et al. High-resolution EBSD study of adiabatic shear band and neighboring grains after dynamic impact loading of Mn-steel used in vehicle structure[J]. Journal of Materials Engineering and Performance, 2016, 25(4): 1611-1620. [22] Meyers M A, Nesterenko V F, LaSalvia J C, et al. Shear localization in dynamic deformation of materials: microstructural evolution and self-organization[J]. Materials Science and Engineering: A, 2001, 317(1): 204-225. [23] Zhen Liang, Zou Dongli, Xu Chengyan, et al.Microstructure evolution of adiabatic shear bands in AM60B magnesium alloy under ballistic impact[J]. Materials Science and Engineering: A, 2010, 527(21/22): 5728-5733. [24] Zhang Weiliang, He Liangju, Lu Zhigang, et al.Microstructural characteristics and formation mechanism of adiabatic shear bands in Al-Zn-Mg-Cu alloy under dynamic shear loading[J]. Materials Science and Engineering: A, 2020, 791: 139430. [25] Meyers M A, Xu Yongbo, Xue Qing, et al.Microstructural evolution in adiabatic shear locali-zation in stainless steel[J]. Acta Materialia, 2003, 51(5): 1307-1325. [26] Yang Yang, Wang Bingfeng.Dynamic recrystallization in adiabatic shear band in α-titanium[J]. Materials Letters, 2006, 60(17/18): 2198-2202. [27] Xiao Ang, Huang Changqing, Cui Xiaohui, et al.Impact of the pulse induced current on the microstructure and mechanical properties of the 7075-T6 aluminum alloy[J]. Journal of Alloys and Compounds, 2022, 911: 165021. [28] Wang Shipeng, Xiao Ang, Lin Yuhong, et al.Impact of the pulse induced current on the microstructure and mechanical properties of the 7075-T6 aluminum alloy[J]. Journal of Alloys and Compounds, 2022, 911: 165021. [29] Wang Shipeng, Xiao Ang, Lin Yuhong, et al.Effect of induced pulse current on mechanical properties and microstructure of rolled 5052 aluminum alloy[J]. Materials Characterization, 2022, 185: 111757. [30] 胡赓祥, 蔡珣, 戎咏华. 材料科学基础[M]. 3版. 上海: 上海交通大学出版社, 2010.
2024, Vol. 39 
