Abstract:Accurate and reliable fault location technology is crucial for DC fault repair and recovery with the rapid development and widespread application of DC distribution networks. The passive traveling wave ranging method has the issues of limited energy and insufficient traveling wave characteristic information. The traditional active traveling wave ranging method partially addresses these issues. However, the effects of line wave speed stability and sampling frequency are susceptible. This paper proposes an active injection DC fault location method based on a solid-state circuit breaker (SSCB). First, the SSCB is utilized to interrupt and actively inject signals with different pulse widths. The time difference between the first end of the injected pulse and the first end of the reflected wave is detected as the time interval of injection waveform propagation. This approach reduces errors caused by sampling frequency limitations. Then, the voltage line modulus of the cable line is extracted as the detection quantity, effectively weakening the coupling effect between the positive and negative lines and providing a stable wave speed measurement. Finally, based on the wavelet transform principle, an improved adaptive modulus maximum approach is proposed to detect the first and last moments of the pulse accurately. This approach also mitigates the impact of noise and transition resistance on ranging accuracy. The simulation results show that the proposed method achieves high fault location accuracy for single-pole ground and bipolar short-circuit faults in a distribution network with a total line length of 10 km. The fault location accuracy is less than 0.55%. Even at a high sampling frequency of 80 kHz in 10 km DC distribution lines, the relative error of fault location remians within 1.14%, which reduces dependence on sampling frequency and enhances the robustness of the method. Moreover, the method exhibits resilience to noise interference at different signal-to-noise ratios. With signal-to-noise ratios of 40 dB, 20 dB, and 5 dB, the fault location accuracy with a relative error of less than 0.67% is consistently achieved. However, when the signal-to-noise ratio drops below 5 dB, the impact of noise on ranging and positioning increases, posing challenges for achieving high-precision fault location. The following conclusions can be drawn from the simulation analysis. (1) The proposed method achieves high-precision fault location under single-pole ground or inter-pole short-circuit faults in DC distribution networks. It does not require additional equipment and is simple to operate. (2) A detection method is introduced to measure the average time difference between the end of the transmitted pulse wave and the end of the reflected wave of pulses with different widths. This method reduces the dependence on sampling accuracy caused by the traveling wave ranging method. (3) An improved adaptive modulus maximum method is proposed based on the principle of wavelet transform. The method adaptively sets the threshold value for modulus maximum selection based on fault line parameters, enhancing the resistance to transition resistance and noise in the distance measurement method. (4) The proposed single-ended ranging method does not need communication, which is suitable for applications without communication functions. However, it has the limitation of a dead zone in near-end ranges. Future research will focus on addressing this issue.
王伟, 帅智康, 李杨, 何梨梨, 方辰晨. 基于固态断路器主动注入式直流故障测距方法[J]. 电工技术学报, 2024, 39(8): 2360-2370.
Wang Wei, Shuai Zhikang, Li Yang, He Lili, Fang Chenchen. Active Injection DC Fault Location Method Based on Solid State Circuit Breaker. Transactions of China Electrotechnical Society, 2024, 39(8): 2360-2370.
[1] 薛士敏, 陈超超, 金毅, 等. 直流配电系统保护技术研究综述[J]. 中国电机工程学报, 2014, 34(19): 3114-3122. Xue Shimin, Chen Chaochao, Jin Yi, et al.A research review of protection technology for DC distribution system[J]. Proceedings of the CSEE, 2014, 34(19): 3114-3122. [2] Beheshtaein S, Cuzner R M, Forouzesh M, et al.DC microgrid protection: a comprehensive review[J]. IEEE Journal of Emerging and Selected Topics in Power Electronics, 2019(99): 1. [3] 李晔, 李斌, 刘晓明, 等. 基于反向行波幅值比的对称单极柔性直流系统行波方向保护[J]. 电工技术学报, 2023, 38(9): 2418-2434. Li Ye, Li Bin, Liu Xiaoming, et al.The direction protection based on the amplitude ratio of the backward traveling wave for the symmetrical mono- pole flexible DC system[J]. Transactions of China Electrotechnical Society, 2023, 38(9): 2418-2434. [4] 葛耀中. 新型继电保护和故障测距的原理与技术[M]. 2版. 西安: 西安交通大学出版社, 2007. [5] 张广斌, 陈柏宇, 束洪春, 等. 基于时域波形特征认知的输电线路近端故障辨识与定位[J]. 电力系统自动化, 2024, 48(5): 146-156. Zhang Guangbin, Chen Boyu, Shu Hongchun, et al.Identification and fault location for proximity faults on transmission lines based on the time-domain waveform feature recognition[J]. Automation of Electric Power Systems, 2024, 48(5): 146-156. [6] 徐峰, 范春菊, 孙秋, 等. 含电力电子变压器的直流配电线路双端故障测距方法[J]. 电力系统及其自动化学报, 2019, 31(10): 73-80. Xu Feng, Fan Chunju, Sun Qiu, et al.Dual-terminal fault location method for DC distribution lines with power electronic transformer[J]. Proceedings of the CSU-EPSA, 2019, 31(10): 73-80. [7] 宋国兵, 李德坤, 褚旭, 等. 基于参数识别原理的VSC-HVDC输电线路单端故障定位[J]. 电网技术, 2012, 36(12): 94-99. Song Guobing, Li Dekun, Chu Xu, et al.One-terminal fault location for VSC-HVDC transmission lines based on principles of parameter identification[J]. Power System Technology, 2012, 36(12): 94-99. [8] 李博通, 刘涛, 杨昕陆, 等. 故障自清除型直流配电网新型双极短路故障元件识别方法[J]. 电工技术学报, 2022, 37(17): 4423-4434. Li Botong, Liu Tao, Yang Xinlu, et al.New fault element identification method of bipolar short-circuit fault in DC distribution network with fault self- clearing[J]. Transactions of China Electrotechnical Society, 2022, 37(17): 4423-4434. [9] 李博雅, 杨耀, 杨立红. 高压直流输电线路单端故障测距组合算法[J]. 电力系统保护与控制, 2014, 42(3): 116-121. Li Boya, Yang Yao, Yang Lihong.A combined method of single-ended fault location for HVDC transmission lines[J]. Power System Protection and Control, 2014, 42(3): 116-121. [10] 李德坤, 宋国兵, 高淑萍, 等. VSC-HVDC输电线路单端行波自动化故障定位方法研究[J]. 电网技术, 2013, 37(4): 1128-1133. Li Dekun, Song Guobing, Gao Shuping, et al.Study on automatic fault location for VSC-HVDC trans- mission lines based on one-terminal traveling wave[J]. Power System Technology, 2013, 37(4): 1128-1133. [11] 张广斌, 束洪春, 于继来, 等. 不依赖双侧时钟同步的输电线双端行波测距[J]. 电工技术学报, 2015, 30(20): 199-209. Zhang Guangbin, Shu Hongchun, Yu Jilai, et al.Double-ended travelling wave fault location inde- pendent of two side time synchronization[J]. Transa- ctions of China Electrotechnical Society, 2015, 30(20): 199-209. [12] 张怿宁, 郝洪民, 李京, 等. 脉冲注入法和单端故障行波法相结合的直流输电系统接地极线路故障测距[J]. 电力系统保护与控制, 2017, 45(20): 117-122. Zhang Yining, Hao Hongmin, Li Jing, et al.Fault location of HVDC grounding electrode lines based on combination of pulse injection method and single- ended fault travelling wave method[J]. Power System Protection and Control, 2017, 45(20): 117-122. [13] 王帅, 毕天姝, 贾科. 基于主动脉冲的MMC- HVDC单极接地故障测距[J]. 电工技术学报, 2017, 32(1): 12-19. Wang Shuai, Bi Tianshu, Jia Ke.Single terminal fault location for MMC-HVDC transmission line using active pulse[J]. Transactions of China Electro- technical Society, 2017, 32(1): 12-19. [14] 宋国兵, 王婷, 张晨浩, 等. 利用全桥MMC注入特征信号的直流自适应重合闸方法[J]. 电网技术, 2019, 43(1): 149-156. Song Guobing, Wang Ting, Zhang Chenhao, et al.Adaptive auto-reclosing of DC line based on characteristic signal injection with FB-MMC[J]. Power System Technology, 2019, 43(1): 149-156. [15] He Dong, Shuai Zhikang, Lei Zhiqi, et al.A SiC JFET-based solid state circuit breaker with digitally controlled current-time profiles[J]. IEEE Journal of Emerging and Selected Topics in Power Electronics, 2019, 7(3): 1556-1565. [16] Wang Wei, Shuai Zhikang, Duan Hong, et al.A single-drive SiC-JFET-SCM for solid state circuit breaker in MVDC distribution networks[J]. IEEE Transactions on Industrial Electronics, 2023, 70(11): 11121-11131 [17] 杨明嘉, 夏成军, 赖胜杰, 等. 基于线芯-护层过渡电阻无功特性的交叉互联电缆故障测距[J/OL]. 电工技术报, 2023, DOI: 10.19595/j.cnki.1000-6753. tces.222277. Yang Mingjia, Xia Chengjun, Lai Shengjie, et al.Fault location of cross-connected cables based on reactive power characteristics of core-sheath transi- tion resistance[J/OL]. Transactions of China Elec- trotechnical Society, 2023, DOI: 10.19595/j.cnki. 1000-6753. tces.222277. [18] 胡昌华, 张军波, 周涛. 基于MATLAB的系统分析与设计-4-小波分析[M]. 西安: 西安电子科技大学出版社, 1999. [19] 姜涛, 高浛, 李筱静, 等. 基于小波耗散能量谱的电力系统强迫振荡源定位[J]. 电工技术学报, 2023, 38(7): 1737-1750. Jiang Tao, Gao Han, Li Xiaojing, et al.Forced oscillation source location in power system using wavelet dissipation energy spectrum[J]. Transactions of China Electrotechnical Society, 2023, 38(7): 1737-1750. [20] 崔芮华, 张振, 佟德栓, 等. 基于改进经验小波变换多特征融合的航空交流串联电弧故障检测[J]. 电工技术学报, 2022, 37(12): 3148-3161. Cui Ruihua, Zhang Zhen, Tong Deshuan, et al.Aviation AC series arc fault detection based on improve empirical wavelet transform multi-feature fusion[J]. Transactions of China Electrotechnical Society, 2022, 37(12): 3148-3161. [21] 赵冠琨, 贾科, 陈金锋, 等. 基于断路器重合闸的柔性直流输电线路单端故障测距方法[J]. 电力系统保护与控制, 2021, 49(7): 48-56. Zhao Guankun, Jia Ke, Chen Jinfeng, et al.A single terminal fault location method for a DC transmission line based on circuit breaker reclosing[J]. Power System Protection and Control, 2021, 49(7): 48-56. [22] 吴学斌, 黄治, 邓惟绩. 基于改进变分模态分解的电缆行波故障定位研究[J]. 湖南电力, 2021, 41(3): 1-6, 11. Wu Xuebin, Huang Zhi, Deng Weiji.Research on cable traveling wave fault location based on improved variational modal decomposition method[J]. Hunan Electric Power, 2021, 41(3): 1-6, 11. [23] 宋国兵, 侯俊杰, 郭冰. 基于主动探测式的混合MMC直流输电系统单端量故障定位[J]. 电网技术, 2021, 45(2): 730-740. Song Guobing, Hou Junjie, Guo Bing.Single-ended fault location of hybrid MMC-HVDC system based on active detection[J]. Power System Technology, 2021, 45(2): 730-740. [24] 陈文, 陈凯平, 夏向阳, 等. 高压直流输电系统输电电缆的故障定位方法[J]. 湖南电力, 2022, 42(6): 123-128. Chen Wen, Chen Kaiping, Xia Xiangyang, et al.Fault location method of HVDC transmission cable[J]. Hunan Electric Power, 2022, 42(6): 123-128. [25] Giannakis A, Peftitsis D.Performance evaluation and limitations of overvoltage suppression circuits for low- and medium-voltage DC solid-state breakers[J]. IEEE Open Journal of Power Electronics, 2021, 2: 277-289.