电工技术学报
|
基于磁心与线圈参数优化的非侵入式磁场取能系统功率密度提升方法
李勇, 罗海军, 杨环宇, 闫一骅
西南交通大学国家轨道交通电气化与自动化工程技术研究中心 成都 610031
Power Density Improvement Method of Non-Invasive Magnetic Field Energy Harvester System Based on Optimization of Magnetic Core and Coil Parameters
Li Yong, Luo Haijun, Yang Huanyu, Yan Yihua
School of Electrical Engineering Southwest Jiaotong University Chengdu 610031 China
全文: PDF (1576 KB)  
输出: BibTeX | EndNote (RIS)      
摘要 非侵入式磁场取能系统具有结构简单、供电稳定等优点,是解决变电站母排环境中状态监测传感器电池供电寿命有限的有效手段,但因功率密度较低制约了其应用。对于非侵入式磁场取能系统,磁心与线圈参数对其功率密度的影响非常显著。然而,现有方法对磁心与线圈参数的分析相对独立,优化磁心时以仅互感为指标,忽略了该过程线圈参数变化对功率密度的影响。对此,本文考虑磁心尺寸对线圈参数的影响,以功率密度为指标,详细分析了线圈匝数、线圈线径、磁柱侧面边长与叠片厚度对系统功率密度的影响。并在此基础上,提出了一种优化磁心与线圈参数的功率密度提升方法,即设计线圈匝数、线圈线径、磁柱侧面边长与叠片厚度的最优值,以获取更高的功率密度。最后,基于所提出方法制作了系统样机并进行测试。实验结果表明,对于限定磁心尺寸为30mm×30mm×40mm的系统,在100A母排电流下,系统经磁心与线圈优化后功率密度可达4.18mW/cm3,提升至系统优化前功率密度的35倍,验证了所提出方法提升功率密度的有效性。
服务
把本文推荐给朋友
加入我的书架
加入引用管理器
E-mail Alert
RSS
作者相关文章
李勇
罗海军
杨环宇
闫一骅
关键词 传感器非侵入式磁场取能磁心线圈功率密度    
Abstract:Wireless sensor is an effective method to monitor the status of the substation busbar. The traditional power supply source of sensors is battery. However, the battery has limited life and needs to be replaced frequently, which brings challenge to the long-term stable operation of the sensor. The non-invasive magnetic field energy harvester system has the advantages of simple structure, stable power supply, and convenient installation, which can effectively solve the power supply problem of the sensor. Due to the core structure of the non-invasive magnetic field energy harvester system is non-closed, the power density of the system is low. And the application of the non-invasive magnetic field energy harvester is seriously restricted.
For the non-invasive magnetic field energy harvester system, the influence of core and coil parameters on its power density is very significant. Especially in the application scenario where the space is limited, the system power density cannot be improved by increasing the volume of magnetic core, so the optimization of the magnetic core and coil parameters is particularly critical in this scenario. Unfortunately, the existing system optimization methods to the analysis of magnetic core and coil parameters are relatively independent, only mutual inductance is taken as the optimization index when optimizing the magnetic core, so the influence of coil parameter changes on the power density is ignored, which cannot accurately guide the design of system prototype.
Considering the influence of magnetic core size on coil parameters, this paper took power density instead of mutual inductance as optimization index, and proposed a power density improvement method to optimize magnetic core and coil parameters. Firstly, the equivalent circuit of the system was analyzed, and the power density expression was established. Then, the optimization direction of improving the induced voltage, reducing the coil resistance and reducing the magnetic core volume were clarified. Secondly, the H-shaped structure magnetic core was proposed, which can effectively gather the magnetic flux and reduce the coil resistance. Based on this structure, the induced voltage, the coil resistance and the magnetic core volume were represented by the parameters of the magnetic core and the coil respectively, and then the influencing factors of the power density were determined. Thirdly, the influences of coil turns, coil diameter, lamination thickness and magnetic column side length on the system power density were analyzed based on the finite element simulation. On this basis, a power density improvement method was proposed by optimizing the magnetic core and coil parameters, that was, designing the optimal values of coil turns, coil diameter, laminate thickness and magnetic column side length to obtain higher power density. Finally, the energy harvester with different core and coil parameters were fabricated based on the proposed method above, and their output performance were tested.
The experimental test results show that for the energy harvester with limited core size of 30mm×30mm×40mm, under the condition of 100A busbar current, the load voltage of the energy harvester is 3.64V after optimization, which meets the power supply demand of most sensors. And the power density can reach 4.18mW/cm3, which is 35 times of the power density before optimization, verifying the effectiveness of the proposed power density improvement method.
Key wordsSensor    non-invasive magnetic field energy harvester    magnetic core    coil    power density   
收稿日期: 2022-10-26     
PACS: TM619  
基金资助:成都国佳电气工程有限公司(NEEC-2022-A07)、西南交通大学新型交叉学科培育基金-前沿科技培育项目(2682022KJ005)和四川省科技厅苗子工程项目(2022017)资助
通讯作者: 李 勇 男,1990年生,副教授,硕士生导师,研究方向为无线电能传输技术、微能量收集技术。E-mail:leeo1864@163.com   
作者简介: 罗海军 男,1998年生,硕士研究生,研究方向微能量收集技术。E-mail:1756449228@qq.com
引用本文:   
李勇, 罗海军, 杨环宇, 闫一骅. 基于磁心与线圈参数优化的非侵入式磁场取能系统功率密度提升方法[J]. 电工技术学报, 0, (): 116-116. Li Yong, Luo Haijun, Yang Huanyu, Yan Yihua. Power Density Improvement Method of Non-Invasive Magnetic Field Energy Harvester System Based on Optimization of Magnetic Core and Coil Parameters. Transactions of China Electrotechnical Society, 0, (): 116-116.
链接本文:  
https://dgjsxb.ces-transaction.com/CN/10.19595/j.cnki.1000-6753.tces.222023          https://dgjsxb.ces-transaction.com/CN/Y0/V/I/116