微秒脉冲电场频率对氮化硼纳米片取向程度及复合材料电热性能的影响

doi:10.19595/j.cnki.1000-6753.tces.190938

摘要
图/表
参考文献
相关文章 (15)

全文: PDF (4233 KB) HTML
输出: BibTeX | EndNote (RIS)

摘要纳秒脉冲电场（电场强度大于200kV/mm）已用于诱导填料的取向排列,以制备高热导率的聚合物基薄膜（120~250μm）复合物。但由于需要极高的纳秒脉冲电压,因此对块状复合物的研究很少。该文采用脉宽1μs、电场仅为11.76kV/mm的微秒脉冲电压制备厚度为1.7mm的块状复合物,研究频率对氮化硼纳米片（BNNSs）取向程度及复合材料热导率的影响。用断面扫描电镜（SEM）和X射线衍射峰（XRD）表征纳米片的取向程度。结果表明,纳米片的取向度和复合材料的热导率随着频率的增加而增加,但在较高频率下其增加速率明显降低。当微秒脉冲电场频率为100Hz时,热导率为0.588W/(m·K),是未施加电场的复合材料的两倍以上。此外,测量了纯环氧树脂和复合材料的交流击穿场强,结果表明,微秒脉冲电场下制备的取向型复合材料的交流击穿性能优于纯环氧树脂。

	服务

	把本文推荐给朋友
	加入我的书架
	加入引用管理器
	E-mail Alert
	RSS
	作者相关文章
	米彦
	刘露露
	葛欣
	桂路

关键词 ：微秒脉冲电场, 取向, 环氧树脂, 氮化硼纳米片, 热导率

Abstract：Nanosecond pulsed electric fields over 200kV/mm have been used for filler alignment in polymer-based thin film (120~250μm) composites to improve their thermal conductivity, but little research has been performed on bulk composites because of the requirement of an extremely high nanosecond pulsed voltage. In this paper, a microsecond pulsed voltage, whose pulse width was 1μs, and electric field was only 11.76kV/mm, was adopted for the first time to prepare bulk composites of 1.7mm. Effects of frequency on orientation and thermal conductivity of composites were studied. The degree of orientation was determined based on cross-sectional scanning electron microscopy (SEM) and X-ray diffraction (XRD) peaks. The results show that the orientation degree and thermal conductivity increase with the increasing frequency, but the increase rate is lower under higher frequencies. The thermal conductivity under 100 Hz is 0.588W/mK, which is more than twice that of composites without application of electric field (0.286W/mK). Additionally, AC breakdown strength was measured, the results show that after BNNSs orientation, the composites still have better AC breakdown performance than pure epoxy resin.

Key words： Microsecond pulsed electric field orientation epoxy resin BN nanosheets thermal conductivity

收稿日期: 2019-07-26

PACS:

TM215.92

基金资助:先进输电技术国家重点实验室开放基金资助项目（GEIRI-SKL-2017-006）

通讯作者: 米彦男,1978年生,教授,博士生导师,研究方向为高电压与绝缘技术。E-mail：miyan@cqu.edu.cn

作者简介: 刘露露女,1994年生,硕士研究生,研究方向为高电压与绝缘技术。E-mail：xz_liulu@163.com

引用本文:

米彦, 刘露露, 葛欣, 桂路. 微秒脉冲电场频率对氮化硼纳米片取向程度及复合材料电热性能的影响[J]. 电工技术学报, 2020, 35(15): 3348-3355. Mi Yan, Liu Lulu, Ge Xin, Gui Lu. Effect of Frequency of Microsecond Pulsed Electric Field on Orientation of BNNSs and Electrical and Thermal Properties of Composites. Transactions of China Electrotechnical Society, 2020, 35(15): 3348-3355.

链接本文:

https://dgjsxb.ces-transaction.com/CN/10.19595/j.cnki.1000-6753.tces.190938 https://dgjsxb.ces-transaction.com/CN/Y2020/V35/I15/3348

[1] Donnay M, Tzavalas S, Logakis E.Boron nitride filled epoxy with improved thermal conductivity and dielectric breakdown strength[J]. Composites Science and Technology, 2015, 110: 152-158.
[2] Idumah C I, Hassan A.Recently emerging trends in thermal conductivity of polymer nanocomposites[J]. Reviews in Chemical Engineering, 2016, 32(4): 413-457.
[3] 张晗, 蔡延雷. 一起500kV 变电站干式空心电抗器故障原因分析[J]. 电力电容器与无功补偿, 2016, 37(1): 47-50.
Zhang Han, Cai Yanlei.Fault analysis on dry-type air-core reactor in 500kV substation[J]. Power Capacitor Reactive Power Compensation, 2016, 37(1): 47-50.
[4] Zhu Zezhou, Li Chaowei, Songfeng E, et al.Enhanced thermal conductivity of polyurethane composites via engineering small/large sizes interconnected boron nitride nanosheets[J]. Composites Science and Technology, 2019, 170: 93-100.
[5] Li Xiangyu, Zha Junwei, Wang Sijiao, et al.Effect of high-thermal conductivity epoxy resin on heat dissipation performance of saturated reactor[J]. IEEE Transactions on Dielectrics and Electrical Insulation, 2017, 24(6): 3898-3905.
[6] 杜伯学, 孔晓晓, 肖萌, 等. 高导热聚合物基复合材料研究进展[J]. 电工技术学报, 2018, 33(14): 3149-3159.
Du Boxue, Kong Xiaoxiao, Xiao Meng, et al.Advances in thermal performance of polymer-based composites[J]. Transactions of China Electrotechnical Society, 2018, 33(14): 3149-3159.
[7] 孟成铭, 王刚. 偶联剂处理BN对PA6基绝缘导热复合材料性能的影响[J]. 塑料工业, 2018, 46(7): 133-137.
Meng Chengming, Wang Gang.The effect of coupling agent treated BN on property of insulating and thermally conductive PA6 composite[J]. China Plastics Industry, 2018, 46(7): 133-137.
[8] Du Boxue, Xiao Meng.Thermal accumulation and tracking failure process of BN-filler epoxy-matrix composite[J]. IEEE Transactions on Dielectrics and Electrical Insulation, 2013, 20(6): 2270-2276.
[9] Hu Jiantao, Huang Yun, Zeng Xiaoliang, et al.Polymer composite with enhanced thermal conductivity and mechanical strength through orientation manipulating of BN[J]. Composites Science and Technology, 2018, 160: 127-137.
[10] Takahashi T, Suzuki K, Awano H, et al.Alignment of vapor-grown carbon fibers in polymer under magnetic field[J]. Chemical Physics Letters, 2007, 436(4-6): 378-382.
[11] Chen Jin, Huang Xingyi, Sun Bin, et al.Highly thermally conductive yet electrically insulating polymer/boron nitride nanosheets nanocomposite films for improved thermal management capability[J]. ACS Nano, 2018, 13(1): 337-345.
[12] Kinoshita S, Kozako M, Hikita M, et al.Effect of electric field application during curing process on thermal conductivity of epoxy composite materials with low content inorganic particles[C]//2012 Annual Report Conference on Electrical Insulation and Dielectric Phenomena, Montreal, QC, Canada, 2012: 183-190.
[13] Martin C A, Sandler J K W, Windle A H, et al. Electric field-induced aligned multi-wall carbon nanotube networks in epoxy composites[J]. Polymer, 2005, 46(3): 877-886.
[14] Cho H B, Nakayama T, Tokoi Y, et al.Facile preparation of a polysiloxane-based hybrid composite with highly-oriented boron nitride nanosheets and an unmodified surface[J]. Composites Science and Technology, 2010, 70(12): 1681-1686.
[15] Cho H B, Tu N C, Fujihara T, et al.Epoxy resin-based nanocomposite films with highly oriented BN nanosheets prepared using a nanosecond-pulse electric field[J]. Materials Letters, 2011, 65(15-16): 2426-2428.
[16] Huynh M T T, Cho H B, Suzuki T, et al. Electrical property enhancement by controlled percolation structure of carbon black in polymer-based nanocomposites via nanosecond pulsed electric field[J]. Composites Science and Technology, 2018, 154: 165-174.
[17] Cho H B, Nakayama T, Suzuki T, et al.Electric-field-assisted fabrication of linearly stretched bundles of microdiamonds in polysiloxane-based composite material[J]. Diamond and Related Materials, 2012, 26: 7-14.
[18] 米彦, 桂路, 邓胜初, 等. 模块化双极性固态指数衰减脉冲电压源研制[J]. 高电压技术, 2019, 45(11): 3721-3729.
Mi Yan, Gui Lu, Deng Shengchu, et al.Development of modular bipolar solid state exponential decay pulse voltage source[J]. High Voltage Engineering, 2019, 45(11): 3721-3729.
[19] 王有元, 王施又, 陆国俊, 等. 纳米AlN改性对干式变压器环氧树脂绝缘性能的影响[J]. 电工技术学报, 2017, 32(7): 174-180.
Wang Youyuan, Wang Shiyou, Lu Guojun, et al.Influence of Nano-AI N modification on the insulation properties of epoxy resin of dry-type transformers[J]. Transactions of China Electrotechnical Society, 2017, 32(7): 174-180.
[20] Wang Xiongwei, Wu Peiyi.Preparation of highly thermally conductive polymer composite at low filler content via a self-assembly process between polystyrene microspheres and boron nitride nanosheets[J]. ACS applied materials & interfaces, 2017, 9(23): 19934-19944.
[21] Tahashi M, Ishihara M, Sassa K, et al.Control of crystal orientation in deposited films of bismuth vaporized in laser and resistance heating methods under a high magnetic field[J]. Materials Transactions, 2003, 44(2): 285-289.
[22] Kim G H, Shkel Y M.Polymeric composites tailored by electric field[J]. Journal of Materials Research, 2004, 19(4): 1164-1174.
[23] Ishibe S, Mori M, Kozako M, et al.A new concept varistor with epoxy/microvaristor composite[J]. IEEE Transactions on Power Delivery, 2013, 29(2): 677-682.
[24] 吴子剑, 王晨, 张明艳, 等. 环氧树脂纳米复合材料界面及其对电性能影响分析[J]. 电工技术学报, 2018, 33(16): 3897-3905.
Wu Zijian, Wang Chen, Zhang Mingyan, et al.Interface of epoxy resin composites, and its influence on electrical performance[J]. Transactions of China Electrotechnical Society, 2018, 33(16): 3897-3905.
[25] 张明艳, 孙婷婷, 张晓虹, 等. 蒙脱土改性环氧树脂复合材料的制备及性能研究[J]. 电工技术学报, 2006, 21(4): 29-34.
Zhang Mingyan, Sun Tingting, Zhang Xiaohong, et al.Study of preparation and properties of organo-montmorillonite modified epoxy nanocomposit[J]. Transactions of China Electrotechnical Society, 2006, 21(4): 29-34.
[26] 王旗, 李喆, 尹毅. 微、纳米无机颗粒/环氧树脂复合材料击穿强度性能[J]. 电工技术学报, 2014, 29(12): 230-235.
Wang Qi, Li Zhe, Yin Yi.The effect of micro and nano inorganic filler on the breakdown strength of epoxy resin[J]. Transactions of China Electrotechnical Society, 2014, 29(12): 230-235.
[27] Ding Qiang, Li Zhonghua, Sheng Shouguo, et al.Effect of the electric pre-stress to dielectric property of epoxy polymer[C]//Proceedings of 2001 International Symposium on Electrical Insulating Materials, Himeji, Japan, 2001: 191-193.
[28] Huang Xingyi, Liu Wenhao, Li Shengtao, et al.Boron nitride based poly (phenylene sulfide) composites with enhanced thermal conductivity and breakdown strength[J]. IEEJ Transactions on Fundamentals and Materials, 2013, 133(3): 66-70.
[29] 黄兴溢, 张强, 江平开. 纳米颗粒形状对线性低密度聚乙烯纳米复合介质电学性能的影响[J]. 中国电机工程学报, 2016, 36(24): 6606-6612.
Huang Xingyi, Zhang Qiang, Jiang Pingkai.Influence of nanoparticle shape on electrical properties of linear low density polyethylene nanocomposites[J]. Proceedings of the CSEE, 2016, 36(24): 6606-6612.