Abstract:The working process of a single-switch quadratic buck converter in discontinuous conduction mode (DCM) is analyzed in this paper. A nonlinear control method, pulse train (PT) control, is used to control the converter in DCM, its steady-state and transient response characteristics are analyzed. The converter with PT control simplifies the controller design, and enjoys a wider voltage conversion ratios especially the fast transient response. Therefore, the converter in this paper is suitable for low output voltage and fast transient response application when the input voltage is high, such as automotive power systems.
[1] Carbajal Gutierrez, Morales Saldana, Leyva Ramos. Modeling of a single-switch quadratic buck converter[J]. IEEE Transactions on Aerospace and Electronic Systems, 2005, 41(4): 1450-1456. [2] Neugebauer T C, Perreault D. Computer-aided optimization of DC/DC converters for automotive applications[J]. IEEE Transactions on Power Electronics, 2003, 18(3): 775-783. [3] Kassakian J G, Miller J M, Traub N. Automotive electronics power up[J]. IEEE Spectrum, 2000, 37(5): 34-39. [4] Morales Saldana, Galarza Quirino. Multiloop controller design for a quadratic Boost converter[C]. IEEE Electric Power Conference, 2007: 362-367. [5] Jonas Reginaldo de Britto, Fabio Vincenzi Romualdo da Silva. Proposal of a DC-DC converter with wide conversion range used in photovoltaic systems and utility power grid for the universal voltage range[C]. IEEE Power Electronics Conference, 2009: 606-611. [6] Maksimovic D, Cuk S. Switching converters with wide DC conversion range[J]. IEEE Transactions on Power Electronics, 1991, 6(1): 151- 157. [7] Pacheco V M, Nascimento A J, Farias V J, et al. A quadratic buck converter with lossless commutation [J]. IEEE Transactions on Industrial Electronics, 2000, 47(47): 264-272. [8] Carbajal Gutierrez, Morales Saldana. Average current- mode control for a quadratic buck converter [C]. IEEE Power Electronics Specialists Conference, 2005: 2146-2150. [9] Siu M, Mok P K, Leung K N. A voltage-mode PWM buck regulator with end-point-prediction[J]. IEEE Transactions on Circuits and Systems II: Express Briefs, 2006, 53(4): 294-298. [10] 卢志飞, 杨平, 刘雪山, 等. 单开关二次型DCM Buck变换器[J]. 电工技术学报, 2011, 26(S1): 65-70. Lu Zhifei, Yang Ping, Liu Xueshan, et al. Single- switch quadratic DCM buck converter[J]. Transac- tions of China Electrotechnical Society, 2011, 26(S1): 65-70. [11] 张占松, 蔡宣三. 开关电源的原理与设计[M]. 北京: 电子工业出版社, 2004: 210-217. [12] 张卫平. 开关变换器的建模与控制[M]. 北京: 中国电力出版社, 2005: 57-74. [13] Luo F, Ma D. A low-ripple fast-response CMOS integrated switching buck converter with dual-mode pulse-trains PWM control[C]. IEEE Power Electro- nics Specialists Conference, 2008: 3432-3436. [14] Luo F, Ma D. An integrated switching DC-DC converter with dual-mode pulse-train PWM control [J]. IEEE Transactions on Circuits and Systems-II: Express Briefs, 2009, 56(2): 152-156. [15] 秦明, 许建平, 牟清波. 开关DC/DC变换器多级脉冲调节控制[J]. 电工技术学报, 2009, 24(9): 108-113. Qin Ming, Xu Jianping, Mu Qingbo. Multilevel-pulse adjustment control technique for switching DC/DC converters[J]. Transactions of China Electrotechnical Society, 2009, 24(9): 108-113. [16] 罗萍, 甄少伟, 李彦麟. 不同调制模式下Boost变换器DCM模态的能量模型与稳定性分析[J]. 中国电机工程学报, 2005, 25(6): 49-54. Luo ping, Zhen Shaowei, Li Yanlin. Energy models and stability analysis of boost converters in DCM for different modulation modes[J]. Proceedings of the CSEE, 2005, 25(6): 49-54. [17] Matsuo H, Harada K. The cascade connection of switching regulators[J]. IEEE Transactions on Industrial Applications, 1976, 12(2): 192-198.