Compact Design of 550 kV Basin-Type Spacer in Gas Insulated Switchgear (Part Ⅲ) —— Downsized Structure Verification
Wang Chao1, Li Wendong1, Chen Junhong1, Li Jinshu1, Gong Ruilei2, Zhang Guanjun1
1. State Key Laboratory of Electrical Insulation and Power Equipment Xi’an Jiaotong University Xi’an 710049 China; 2. Shandong Taikai High Voltage Switchgear Co. Ltd Tai’an 271000 China
Abstract:Solid insulators are key components in gas insulated equipment including gas insulated switchgear (GIS) and gas insulated transmission line (GIL). Surface flashover across the spacer/gas interface threats the running of GIS/GIL. Hence, it is urgent to enhance the surface insulation strength of spacer especially in the situations where compact design and/or the usage of eco-friendly gases are required. Numerous studies revealed that locally intensified electric (E) field caused by dielectric mismatch or metal particles mainly accounts for the insulation failure of spacer. To design and fabricate a downsized 550 kV spacer in GIS that takes both the structure optimization and dielectric distribution optimization into account, a fabrication method that considering E field mitigation effectiveness and the fabrication efficiency was proposed. Firstly, 1:10 downsized dielectrically graded 550 kV spacers were fabricated by combining stereolithography 3D printing technology with epoxy resin casting technique. Specifically, alumina/UV-cured resin composite was prepared as a low relative permittivity (3.98<εr<4.20) 3D printed slurry to fabricate the main parts of insulators. The characterizations of composites’ photocuring and rheological behaviors indicated that the doping of alumina fillers decreases the photo-curing depth and increase the viscosity particularly in high fillers’ loading content. The processing performance of composite deteriorated when loading content exceeds 30%, since the viscosity pronouncedly increases. After determining fillers’ loading content and printing parameters, the main part of spacers with low permittivity was fabricated by stereolithography 3D printing. Characterization of its dielectric properties confirmed the correctness of permittivity range. Subsequently, titania/epoxy resin composite was prepared as high relative permittivity (11.32<εr<14.58) vacuum casted slurry. To guarantee good match at interface, composite with 30% titania loading content was selected. The characterizations of composites’ rheological behaviors indicated that the viscosity of composite dramatically decreases with the increase of temperature, benefiting the flowing of slurry in the reserved high permittivity region in the 3D printed spacer. After determining the curing conditions, the slurry was heated and then cured to finish the downsized spacer manufacturing. Secondly, flashover tests of spacers before and after optimization ware carried out in compressed SF6 gas. Characterizations of power frequency withstand voltage indicated that insulation structures after optimization exhibit improved electrical performance. Comparing with an original insulation structure, geometrically optimized spacer shows a 13.6% flashover voltage improvement, and this improvement increase to 13.8% for geometrically/dielectrically optimized spacer. After reducing a 15% of insulation distance, geometrically/ dielectrically optimized spacer shares the same insulation level with the original structure. When a metal wire existing in the wedgy airgap at the flange side, improved electrical strength of the geometrically optimized spacer at the same insulation distance reduces to 6.7%. In contrast, owing to the low electric field area forming by the spacer with further optimized dielectric distribution, a 13.1% flashover voltage improvement still could be maintained, indicating the insulation excellence of the geometrically/dielectrically optimized spacer. The proposed spacer construction strategy takes both optimization effectiveness and fabrication efficiency into account, and the fabricated dielectrically graded 550 kV spacers exhibit excellent surface electrical insulation properties, offering the possibility of reducing size of GIS tank, and is considered as an essential step towards the industrial application of 3D printed spacer in GIS/GIL.
[1] Pleşa I, Noţingher P V, Schlögl S, et al.Properties of polymer composites used in high-voltage applications[J]. Polymers, 2016, 8(5): 173. [2] 何愈, 何俊凌, 赵玉顺, 等. 特高压电气设备用高性能复合绝缘材料配方的研制[J]. 热固性树脂, 2020, 35(6): 54-61. He Yu, He Junling, Zhao Yushun, et al.Development of high performance composite insulating material formula for UHV electrical equipment[J]. Thermo-setting Resin, 2020, 35(6): 54-61. [3] 赵玉顺, 何元菡, 杨克荣, 等. Me-THPA扩链改性环氧树脂对其固化物绝缘特性的影响[J]. 电工技术学报, 2020, 35(增刊1): 311-319. Zhao Yushun, He Yuanhan, Yang Kerong, et al.Insulation performance of Me-THPA chain-extended epoxy resin cured products[J]. Transactions of China Electrotechnical Society, 2020, 35(S1): 311-319. [4] 张冠军, 李文栋, 刘哲, 等. 介电功能梯度材料在电气绝缘领域的研究进展[J]. 中国电机工程学报, 2017, 37(14): 4232-4245, 4303. Zhang Guanjun, Li Wendong, Liu Zhe, et al.Research progress on dielectric functionally graded materials for electrical insulation[J]. Proceedings of the CSEE, 2017, 37(14): 4232-4245, 4303. [5] Li Jin, Liang Hucheng, Chen Yun, et al.Promising functional graded materials for compact gaseous insulated switchgears/pipelines[J]. High Voltage, 2020, 5(3): 231-240. [6] Hayakawa N, Miyaji Y, Kojima H, et al.Simulation on discharge inception voltage improvement of GIS spacer with permittivity graded materials (ε-FGM) using flexible mixture casting method[J]. IEEE Transactions on Dielectrics and Electrical Insulation, 2018, 25(4): 1318-1323. [7] Li Chuanyang, Lin Chuanjie, Yang Yong, et al.Novel HVDC spacers by adaptively controlling surface charges-part Ⅱ: experiment[J]. IEEE Transactions on Dielectrics and Electrical Insulation, 2018, 25(4): 1248-1258. [8] Shen Zikui, Wang Xilin, Zhang Tianfeng, et al.In situ electric field driven assembly to construct adaptive graded permittivity BaTiO3/epoxy resin composites for improved insulation performance[J]. Applied Materials Today, 2020, 20: 100647. [9] Li Jin, Liang Hucheng, Du Boxue, et al.Surface functional graded spacer for compact HVDC gaseous insulated system[J]. IEEE Transactions on Dielectrics and Electrical Insulation, 2019, 26(2): 664-667. [10] Du Boxue, Wang Zehua, Li Jin, et al.Epoxy insulator with surface graded-permittivity by magnetron sputtering for gas-insulated line[J]. IEEE Transactions on Dielectrics and Electrical Insulation, 2020, 27(1): 197-205. [11] Xue Jianyi, Chen Junhong, Dong Junhao, et al.The regulation mechanism of SiC/epoxy coatings on surface charge behavior and flashover performance of epoxy/alumina spacers[J]. Journal of Physics D: Applied Physics, 2019, 52(40): 405502. [12] Li Xiaoran, Liu Zhe, Li Wendong, et al.3D printing fabrication of conductivity non-uniform insulator for surface flashover mitigation[J]. IEEE Transactions on Dielectrics and Electrical Insulation, 2019, 26(4): 1172-1180. [13] Li Wendong, Wang Chao, Jiang Zhihui, et al.Stereolithography based additive manufacturing of high-k polymer matrix composites facilitated by thermal plasma processed barium titanate microspheres[J]. Materials & Design, 2020, 192: 108733. [14] 王超, 李文栋, 江智慧, 等.氟硅烷修饰的纳米复合光固化涂层提升绝缘真空闪络特性[J]. 高电压技术, 2021, 47(3): 1028-1036. Wang Chao, Li Wendong, Jiang Zhihui, et al.Study on the vacuum flashover of insulator with fluorosilane modified nanocomposite UV curable coating[J]. High Voltage Engineering, 2021, 47(3): 1028-1036. [15] 王超, 李文栋, 陈泰然, 等. 550 kV GIS盆式绝缘子小型化设计(一)——几何形状优化[J]. 电工技术学报, 2022, 37(7): 1847-1855. Wang Chao, Li Wendong, Chen Tairan, et al.Compact design of 550 kV basin-type spacer in gas insulated switchgear (partⅠ)——structure optimization[J]. Transactions of China Electrotechnical Society, 2022, 37(7): 1847-1855. [16] 李文栋,王超, 陈泰然, 等. 550 kV GIS盆式绝缘子小型化设计(二)——介电分布优化[J]. 电工技术学报, 2022, 37(11): 2743-2752. Wang Chao, Li Wendong, Jiang Zhihui, et al.Compact design of 550 kV basin-type spacer in gas insulated switchgear (part Ⅱ)——dielectric distribution optimi-zation[J]. Transactions of China Electrotechnical Society, 2022, 37(11): 2743-2752. [17] Xing Hongyu, Zou Bin, Liu Xiaoyan, et al.Effect of particle size distribution on the preparation of ZTA ceramic paste applying for stereolithography 3D printing[J]. Powder Technology, 2020, 359: 314-322. [18] 黄笔武, 黄伯芬, 谌伟庆, 等. 光固化快速成形光敏树脂临界曝光量和透射深度的测试研究[J]. 信息记录材料, 2007, 8(1): 59-62. Huang Biwu, Huang Bofen, Chen Weiqing, et al.Determination of the critical exposure and the penetration depth of the photosensitive resin for Stereolithography[J]. Information Recording Materials, 2007, 8(1): 59-62. [19] 吴其晔, 巫静安. 高分子材料流变学[M]. 2版. 北京: 高等教育出版社, 2014. [20] 毕全瑞, 郝留成, 袁端鹏, 等. 盆式绝缘子用环氧/氧化铝复合体系固化动力学[J]. 高电压技术, 2019, 45(9): 2758-2765. Bi Quanrui, Hao Liucheng, Yuan Duanpeng, et al.Curing kinetics of epoxy/alumina composite system for basin insulator[J]. High Voltage Engineering, 2019, 45(9): 2758-2765. [21] Huang Xingyi, Xie Liyuan, Yang Ke, et al.Role of interface in highly filled epoxy/BaTiO3 nanocomposites. Part I-correlation between nanoparticle surface chemistry and nanocomposite dielectric property[J]. IEEE Transactions on Dielectrics and Electrical Insulation, 2014, 21(2): 467-479. [22] Kremer F, Schönhals A.Broadband dielectric spectroscopy[M]. Berlin, Heidelberg: Springer, 2003. [23] 闫翔宇, 袁颖, 张树人, 等. SiO2-TiO2/聚四氟乙烯复合材料的制备及热膨胀性能[J]. 复合材料学报, 2013, 30(6): 108-113. Yan Xiangyu, Yuan Ying, Zhang Shuren, et al.Fabrication and thermal expansion behavior of SiO2-TiO2 ceramic filled PTFE composites[J]. Acta Materiae Compositae Sinica, 2013, 30(6): 108-113. [24] Al-Ahdal K, Silikas N, Watts D C.Rheological properties of resin composites according to variations in composition and temperature[J]. Dental Materials, 2014, 30(5): 517-524. [25] Min Daomin, Yan Chenyu, Mi Rui, et al.Carrier transport and molecular displacement modulated dc electrical breakdown of polypropylene nanocom-posites[J]. Polymers, 2018, 10(11): 1207.