Eddy Currents Competition in Electromagnetic Forming Process of Plates by Double-Coil Attraction
Xiong Qi1,2, Yang Meng1,2, Zhou Lijun1,2, Song Xianqi1,2, Li Zhe1,2
1. College of Electrical Engineering & New Energy China Three Gorges University Yichang 443002 China; 2. Hubei Provincial Engineering Technology Research Center for Power Transmission Line China Three Gorges University Yichang 443002 China
Abstract:Electromagnetic forming (EMF) is a kind of high energy processing technology that realizes rapid plastic forming of light alloy pieces by the pulsed electromagnetic force. Attraction electromagnetic forming is one of the unique applications. It uses two different pulse width currents to drive one coil to generate an attractive electromagnetic force, which is suitable for plate dent repairment and micro-tube forming. However, the single-coil structure has very strict requirements for parameter matching of the two currents, and the energy utilization efficiency is extremely low. Therefore, this paper puts forward a double-coil structure attracting electromagnetic scheme, that is, two kinds of current are used to drive a coil each. However, the double-coil structure brings new eddy current competition phenomenon, which will cause forming defects. Thus, this paper further studies the cause and mechanism of eddy current competition, and finally eliminates the forming defects by adjusting the coil structural parameters in the scheme of AA1060-H28 aluminum alloy plate with a diameter of 200 mm. This paper provides a better understanding of the attractive EMF process, and has significance for expanding the application of the EMF technology in plate processing.
熊奇, 杨猛, 周丽君, 宋先祺, 李哲. 双线圈吸引式板件电磁成形过程中的涡流竞争问题[J]. 电工技术学报, 2021, 36(10): 2007-2017.
Xiong Qi, Yang Meng, Zhou Lijun, Song Xianqi, Li Zhe. Eddy Currents Competition in Electromagnetic Forming Process of Plates by Double-Coil Attraction. Transactions of China Electrotechnical Society, 2021, 36(10): 2007-2017.
[1] 熊奇, 唐红涛, 王沐雪, 等. 2011年以来电磁成形研究进展[J]. 高电压技术, 2019, 45(4): 1171-1181. Xiong Qi, Tang Hongtao, Wang Muxue, et al.Research progress of electromagnetic forming tech- nique since 2011[J]. High Voltage Engineering, 2019, 45(4): 1171-1181. [2] Psyk V, Risch D, Kinsey B L, et al.Electromagnetic forming-a review[J]. Journal of Materials Processing Technology, 2011, 211(5): 787-829. [3] 邱立, 李彦涛, 苏攀, 等. 电磁成形中电磁技术问题研究进展[J]. 电工技术学报, 2019, 34(11): 2247-2259. Qiu Li, Li Yantao, Su Pan, et al.Research on electromagnetic problems in electromagnetic forming process[J]. Transactions on China Electrotechnical Society, 2019, 34(11): 2247-2259. [4] Xiong Qi, Tang Hongtao, Deng Changzheng, et al.Electromagnetic attraction-based bulge forming in small tubes: fundamentals and simulations[J]. IEEE Transactions on Applied Superconductivity, 2017, 28(3): 1-5. [5] Qiu Li, Li Yantao, Yu Yijie, et al.Numerical and experimental investigation in electromagnetic tube expansion with axial compression[J]. The Inter- national Journal of Advanced Manufacturing Tech- nology, 2019, 104(5-8): 3045-3051. [6] 邱立, 杨新森, 常鹏, 等. 双线圈轴向压缩式管件电磁胀形电磁力分布规律与管件成形性能研究[J]. 电工技术学报, 2019, 34(14): 2855-2862. Qiu Li, Yang Xinsen, Chang Peng, et al.Electro- magnetic force distribution and forming performance in electromagnetic tube expansion process with two coils[J]. Transactions on China Electrotechnical Society, 2019, 34(14): 2855-2862. [7] Yu Haiping, Li ChunFeng, Deng JiangHua. Sequential coupling simulation for electromagnetic-mechanical tube compression by finite element analysis[J]. Journal of materials processing technology, 2009, 209(2): 707-713. [8] Xu Junrui, Xie Xueyun, Wen Zhisheng, et al.Deformation behaviour of AZ31 magnesium alloy sheet hybrid actuating with Al driver sheet and temperature in magnetic pulse forming[J]. Journal of Manufacturing Processes, 2019, 37: 402-412. [9] Cao Quanliang, Du Limeng, Li Zhenhao, et al.Investigation of the lorentz-force-driven sheet metal stamping process for cylindrical cup forming[J]. Journal of Materials Processing Technology, 2019, 271: 532-541. [10] Kumar S, Khan M R, Saroj P C, et al.Experimental investigation of driver material on electromagnetic welding of alloy D9 SS tube to SS316L (N) plug[J]. The International Journal of Advanced Manufacturing Technology, 2019, 105(10): 4225-4235. [11] Deng Fangxiong, Cao Quanliang, Han Xiaotao, et al.Electromagnetic pulse spot welding of aluminum to stainless steel sheets with a field shaper[J]. The International Journal of Advanced Manufacturing Technology, 2018, 98(5-8): 1903-1911. [12] 周纹霆, 董守龙, 王晓雨, 等. 电磁脉冲焊接电缆接头的装置的研制及测试[J]. 电工技术学报, 2019, 34(11): 2424-2434. Zhou Wenting, Dong Shoulong, Wang Xiaoyu, et al.Development and test of electromagnetic pulse welding cable joint device[J]. Transactions on China Electrotechnical Society, 2019, 34(11): 2424-2434. [13] Lai Zhipeng, Cao Quanliang, Han Xiaotao, et al.Investigation on plastic deformation behavior of sheet workpiece during radial lorentz force augmented deep drawing process[J]. Journal of Materials Processing Technology, 2017, 245: 193-206. [14] Deng Jianghua, Li Chunfeng, Zhao Zhiheng, et al.Numerical simulation of magnetic flux and force in electromagnetic forming with attractive force[J]. Journal of Materials Processing Technology, 2007, 184(1-3): 190-194. [15] Cao Quanliang, Lai Zhipeng, Xiong Qi, et al.Elec- tromagnetic attractive forming of sheet metals by means of a dual-frequency discharge current: design and implementation[J]. The International Journal of Advanced Manufacturing Technology, 2017, 90(1-4): 309-316. [16] Xiong Qi, Tang Hongtao, Wang Muxue, et al.Design and implementation of tube bulging by an attractive electromagnetic force[J]. Journal of Materials Pro- cessing Technology, 2019, 273: 116240. [17] Ouyang Shaowei, Li Xiaoxiang, Li Changxing, et al.Investigation of the electromagnetic attractive forming utilizing a dual-coil system for tube bulging[J]. Journal of Manufacturing Processes, 2020, 49: 102-115. [18] Xiong Qi, Yang Meng, Liu Xin, et al.A dual-coil method for electromagnetic attraction forming of sheet metals[J]. IEEE Access, 2020, 8: 92708-92717. [19] 熊奇. 采用双线圈的金属板件吸引式成形方法及成形装置[P]. 中国: CN110899452A, 2020-03-24. [20] Mamalis A G, Manolakos D E, Kladas A G, et al.Electromagnetic forming tools and processing con- ditions: numerical simulation[J]. Materials and Manufacturing Processes, 2006, 21(4): 411-423. [21] 黎镇浩, 曹全梁, 赖智鹏, 等. 电流丝法在电磁成形线圈电流和工件电磁力计算中的应用[J]. 电工技术学报, 2018, 33(18): 4181-4190. Li Zhenhao, Cao Quanliang, Lai Zhipeng, et al.Application of current filament method on the calculation of current and force in electromagnetic forming[J]. Transactions on China Electrotechnical Society, 2018, 33(18): 4181-4190. [22] Xiong Qi, Huang Hao, Xia Liangyu, et al.A research based on advance dual-coil electromagnetic forming method on flanging of small-size tubes[J]. The Inter- national Journal of Advanced Manufacturing Techno- logy, 2019, 102(9-12): 4087-4094. [23] 邱立, 余一杰, 聂小鹏, 等. 管件电磁胀形过程中的材料变形性能问题与电磁力加载方案[J]. 电工技术学报, 2019, 34(2): 212-218. Qiu Li, Yu Yijie, Nie Xiaopeng, et al.Study on material deformation performance and electromagnetic force loading in electromagnetic tube expansion process[J]. Transactions on China Electrotechnical Society, 2019, 34(2): 212-218. [24] Cao Quanliang, Li Liang, Lai Zhipeng, et al.Dynamic analysis of electromagnetic sheet metal forming process using finite element method[J]. The Inter- national Journal of Advanced Manufacturing Tech- nology, 2014, 74(1-4): 361-368. [25] Cao Quanliang, Han Xiaotao, Lai Zhipeng, et al.Analysis and reduction of coil temperature rise in electromagnetic forming[J]. Journal of Materials Pro- cessing Technology, 2015, 225: 185-194.