Application of Current Filament Method on the Calculation of Current and Force in Electromagnetic Forming
Li Zhenhao1, 2, Cao Quanliang1, 2, Lai Zhipeng1, 2, Han Xiaotao1, 2, Li Liang1, 2
1. Wuhan National High Magnetic Field Center Huazhong University of Science and Technology Wuhan 430074 China; 2. School of Electrical and Electronic Engineering Huazhong University of Science and Technology Wuhan 430074 China
Abstract:Accurate calculations of coil current and electromagnetic force in the workpiece in electromagnetic forming (EMF) system are essential to analyze the dynamic behavior of workpiece and optimize electromagnetic parameters. By now, finite element method (FEM) has been widely applied to simulate these two parameters. However, when the coupling analysis of electromagnetic and structure fields is carried out using FEM, large or complicated workpiece deformation can easily cause the air mesh distortion, which leads to low accuracy, poor convergence and long simulation time. Therefore, this paper studies the calculation of coil current and electromagnetic force in workpiece in EMF based on current filament method (CFM). Taken the numerical results by COMSOL as references, comparative analysis of the conventional and improved CFMs is carried out. The results show that the improved CFM proposed in this work can reflect the distribution characteristics of coil current and electromagnetic force in workpiece more accurately with considering the skin effect. It is because the computational accuracy of mutual inductances as well as their gradients of each current filament in the equivalent circuit has been improved when each coil turn was divided into several parts. On this basis, the validity and applicability of the proposed method for EMF are verified by analyzing the computational performance under different discharge frequencies, coil conductor sizes and workpiece geometries.
黎镇浩, 曹全梁, 赖智鹏, 韩小涛, 李亮. 电流丝法在电磁成形线圈电流和工件电磁力计算中的应用[J]. 电工技术学报, 2018, 33(18): 4181-4190.
Li Zhenhao, Cao Quanliang, Lai Zhipeng, Han Xiaotao, Li Liang. Application of Current Filament Method on the Calculation of Current and Force in Electromagnetic Forming. Transactions of China Electrotechnical Society, 2018, 33(18): 4181-4190.
[1] Xu Da, Liu Xuesong, Fang Kun, et al.Calculation of electromagnetic force in electromagnetic forming process of metal sheet[J]. Journal of Applied Physics, 2010, 107(12): 124907. [2] Psyk V, Risch D, Kinsey B L, et al.Electromagnetic forming-a review[J]. Journal of Materials Processing Technology,2011, 211(5): 787-829. [3] Mamalis A G, Manolakos D E.Electromagnetic forming and powder processing: trends and deve- lopments[J]. Applied Mechanics Reviews, 2004, 57(4): 299-324. [4] Seth M, Vohout V J, Daehn G S. Formability of steel sheet in high velocity impact[J]. Journal of Materials Processing Technology, 2005, 168(30: 390-400. [5] Fenton G K, Daehn G S.Modeling of electro- magnetically formed sheet metal[J]. Journal of Materials Processing Technology, 1998, 75(1): 6-16. [6] Cao Quanliang, Li Liang, Lai Zhipeng, et al.Dynamic analysis of electromagnetic sheet metal forming process using finite element method[J]. The International Journal of Advanced Manufacturing Technology, 2014, 74(1): 361-368. [7] Lal G K, Hillier M J.The electrodynamics of electromagnetic forming[J]. International Journal of Mechanical Sciences, 1968, 10(6): 491-500. [8] Jablonski J, Winkler R.Analysis of the electro- magnetic forming process[J]. International Journal of Mechanical Sciences, 1978, 20(5): 315-325. [9] Gourdin W H.Analysis and assessment of electro- magnetic ring expansion as a high-strain-rate test[J]. Journal of Applied Physics, 1989, 65(2): 411-422. [10] Hainsworth G, Leonard P J, Rodger D, et al.Finite element modelling of magnetic compression using coupled electromagnetic-structural codes[J]. IEEE Transactions on Magnetics, 1996, 32(3): 1050-1053. [11] Oliveira D A, Worswick M J, Finn M, et al.Electromagnetic forming of aluminum alloy sheet: free-form and cavity fill experiments and model[J]. Journal of Materials Processing Technology, 2005, 170(1): 350-362. [12] Yu Haiping, Li Chunfeng, Deng Jianghua, et al.Sequential coupling simulation for electromagnetic- mechanical tube compression by finite element analysis[J]. Journal of Materials Processing Technology, 2009, 209(2): 707-713. [13] Bartels G, Schätzing W, Scheibe H P, et al.Comparison of two different simulation algorithms for the electromagnetic tube compression[J]. International Journal of Material Forming, 2009, 2(1): 693-696. [14] Li Ling, Han Xiaotao, Peng Tao, et al.Development of space-time-controlled multi-stage pulsed magnetic field forming and manufacturing technology at the WHMFC[C]//The 6th International Conference on High Speed Forming, Daejeon, Korea, 2014: 353-362. [15] Wu A Y, Sun K S.Formulation and implementation of the current filament method for the analysis of current diffusion and heating in conductors in railguns and homopolar generators[J]. IEEE Transactions on Magnetics, 1989, 25(1): 610-615. [16] Luo J, Novac B M, Smith I R, et al.Fast and accurate two-dimensional modelling of high-current, high- voltage air-cored transformers[J]. Journal of Physics D: Applied Physics, 2005, 38(6): 955-963. [17] Paese E, Geier M, Homrich R P, et al.A coupled electric-magnetic numerical procedure for deter- mining the electromagnetic force from the interaction of thin metal sheets and spiral coils in the electromagnetic forming process[J]. Applied Mathe- matical Modelling, 2015, 39(1): 309-321. [18] Zhang Xiao, Cao Quanliang, Han Xiaotao, et al.Application of triple-coil system for improving deformation depth of tube in electromagnetic forming[J]. IEEE Transactions on Applied Super- conductivity, 2016, 26(4): 3701204. [19] Lai Zhipeng, Cao Quanliang, Han Xiaotao, et al.Investigation on plastic deformation behavior of sheet workpiece during radial Lorentz force augmented deep drawing process[J]. Journal of Materials Processing Technology, 2017, 245: 193-206. [20] 刘守豹, 阮江军, 彭迎, 等. 改进型电流丝法及其在感应线圈炮场路结合分析中的应用[J]. 中国电机工程学报, 2010, 30(30): 128-134. Liu Shoubao, Ruan Jiangjun, Peng Ying, et al.Improvement of current filament method and its application in performance analysis of induction coil gun[J]. Proceedings of the CSEE, 2010, 30(30): 128-134. [21] 肖后秀, 李亮. 脉冲磁体的电感计算[J]. 电工技术学报,2010, 25(1): 14-18 Xiao Houxiu, Li Liang.Inductance calculation for pulsed magnets[J]. Transactions on China Electro- technical Society, 2010, 25(1): 14-18. [22] Cao Quanliang, Han Xiaotao, Lai Zhipeng, et al.Analysis and reduction of coil temperature rise in electromagnetic forming[J]. Journal of Materials Processing Technology, 2015, 225: 185-194.