Abstract：Wireless charging technology is safer and more convenient than traditional wired charging, and has been widely used in the field of electric vehicles. However, wireless charging systems have the characteristic of separating the ground end and the vehicle end, and there are issues with the selection and measurement of power metering points. The mainstream approach is to set the measurement position of the wireless charging system on the transmitting coil. However, the current and voltage of the transmitting coil are relatively high, so that directly using sensors for measurement can lead to high sensor costs. To address the aforementioned issues, this paper proposed a non-contact measurement method for output power of transmitting coil of wireless charging systems using multi coil collaboration. This method did not require specialized high-power high-frequency current and voltage sensors, and adapted well to practical scenarios such as different power levels, horizontal and vertical ground displacement of cars, and shielding materials, and had high measurement accuracy. The paper utilized the law of electromagnetic induction to measure the output power of transmitting coil by setting sensing coils. Firstly, it was inferred that there was a relationship between the output power of transmitting coil and the voltage product of the sensing coil. Secondly, the fitting coefficient was used to fit this relationship, and it was derived that when the positions of detection coils and transmission coil were fixed, the fitting coefficient did not shift with the receiving coil. After obtaining the fitting coefficient, only the terminal voltage of the sensing coil needed to be measured. Finally, by constructing the voltage matrix of sensing coils and the standard output power of transmitting coil matrix, the fitting coefficients were obtained, and a coupling matrix model was established between the voltage phasor of each sensing coil and the output power of transmitting coil considering horizontal offset, vertical offset, and power variation. The experimental results show that under different power levels, the maximum measurement error of the proposed method is within 1.5% when the wireless charging system undergoes offset in both horizontal and vertical ground directions. Under the condition of 2 square sensing coils, the maximum error in power measurement was 47%. When the number of sensing coils increased to 6, the maximum error decreased to within 1.5%. This result indicates that as the number of sensing coils increases, the accuracy will further improve. Meanwhile, research has found that when the transmitting and receiving coil are square, using a square sensing coil results in more ideal accuracy. In addition, with the use of 6 detection coils, 3, 5, and 9 power sampling points were used within the measured power range. The maximum errors in power measurement were 7.8%, 3.6%, and 1.5%, respectively, indicating that the more sampling points are, the more accurate the model is. Finally, further exploration is conducted on the practical scenario of placing multiple sensing coils horizontally, which can avoid the problem of vertical stacking height affecting the short distance power measurement. This method has been proven to be effective through simulation and experimental analysis. Through comparative analysis of the results, the following conclusions can be drawn: (1) The size and quantity of detection coils are key to ensuring the accuracy of the model. A sufficient number of sensing coils will bring higher model accuracy, but at the same time, it will also increase the number of samples in the model solving process. Therefore, in practice, a reasonable selection can be made based on the measured power error requirements. (2) For coupling devices where both the transmitting and receiving coils are square coils, the measurement accuracy using square sensing coils is more ideal compared to circular sensing coils. (3) A sufficient number of sampling points in model solving can also affect the accuracy of the entire system model. In practice, a reasonable selection can be made based on the measured power error requirements. (4) Horizontal placement of multiple sensing coils can achieve high-precision power measurement, just like vertical stacking. In practical scenarios, placing multiple sensing coils horizontally can avoid the problem of vertical stacking height affecting the short distance measurement of the transmitting and receiving coils.
谭林林, 王嘉琦. 基于多感测线圈协同的无线充电系统发射线圈输出功率测量方法[J]. 电工技术学报, 2025, 40(12): 3727-3741.
Tan Linlin, Wang Jiaqi. Measurement Method for Output Power of Transmitting Coil in Wireless Charging System Based on Multi Sensing Coil Collaboration. Transactions of China Electrotechnical Society, 2025, 40(12): 3727-3741.
[1] 杨庆新, 张献, 章鹏程. 电动车智慧无线电能传输云网[J]. 电工技术学报, 2023, 38(1): 1-12. Yang Qingxin, Zhang Xian, Zhang Pengcheng.Intelligent wireless power transmission cloud network for electric vehicles[J]. Transactions of China Elec-trotechnical Society, 2023, 38(1): 1-12. [2] 荣灿灿, 严俐慧, 路聪慧, 等. 基于超材料与超表面的无线电能传输技术研究现状与进展综述[J]. 电工技术学报, 2023, 38(20): 5369-5384. Rong Cancan, Yan Lihui, Lu Conghui, et al.Overview on research status and progress of wireless power transfer technology based on metamaterials and metasurfaces[J]. Transactions of China Electrotech-nical Society, 2023, 38(20): 5369-5384. [3] 杨继鑫, 史黎明, 殷正刚, 等. 感应电能传输系统多并联拾取模块电流和输出功率均衡方法[J]. 电力系统自动化, 2024, 48(5): 120-127. Yang Jixin, Shi Liming, Yin Zhenggang, et al.Current and output power balancing method for multiple parallel pickup modules in inductive power transfer system[J]. Automation of Electric Power Systems, 2024, 48(5): 120-127. [4] 周少聪, 俞小明, 王骏, 等. 基于原副边协同控制的无线充电系统能效提升方法[J/OL]. 电源学报, 1-12[2025-03-07]. http://kns.cnki.net/kcms/detail/12.1420.tm.20241204.1536.010.html. Zhou Shaocong, Yu Xiaoming, Wang Jun, et al. Energy efficiency improvement method for wireless charging system based on primary and secondary edge collaborative control[J/OL]. Journal of Power Supply, 1-12[2025-03-07]. http://kns.cnki.net/kcms/detail/12.1420.tm.20241204.1536.010.html. [5] 孙天, 宋贝贝, 崔淑梅, 等. 电动汽车无线充电系统接收端位置大范围唯一性辨识系统设计[J]. 电工技术学报, 2024, 39(21): 6626-6635, 6792. Sun Tian, Song Beibei, Cui Shumei, et al.Design of wide range unique identification system for receiving terminal location of wireless charging system for electric vehicles[J]. Journal of Electrical Engineering, 2024, 39(21): 6626-6635, 6792. [6] 余庆昌, 李浩然, 朱玉玉. 磁耦合谐振式无线充电线圈的优化方法研究[J/OL]. 电源学报, 1-14[2025-03-07]. http://kns.cnki.net/kcms/detail/12.1420.TM.20240425.1639.002.html. Yu Qingchang, Li Haoran, Zhu Yuyu. Research on optimization method of magnetic coupling resonance wireless charging coil[J/OL]. Journal of Power Supply, 1-14[2025-03-07]. http://kns.cnki.net/kcms/detail/12.1420.TM.20240425.1639.002.html. [7] 范宏, 李嘉晖, 郭琦. 考虑用户充电决策行为的电动汽车充电引导策略[J]. 电力工程技术, 2023, 42(4): 23-30. Fan Hong, Li Jiahui, Guo Qi.Electric vehicle charging guidance strategy considering user charging decision behavior[J]. Electric Power Engineering Technology, 2023, 42(4): 23-30. [8] 夏鑫, 钟浩, 张磊, 等. 计及动态电价的电动汽车参与微电网调度双层优化策略[J]. 电力工程技术, 2024, 43(3): 140-150. Xia Xin, Zhong Hao, Zhang Lei, et al.Dual layer optimization strategy for electric vehicles participating in microgrid scheduling considering dynamic elec-tricity prices[J]. Electric Power Engineering Techno-logy, 2024, 43(3): 140-150. [9] González-González J M, Triviño-Cabrera A, Aguado J A. Assessment of the power losses in a SAE J2954-compliant wireless charger[J]. IEEE Access, 2022, 10: 54474-54483. [10] Nakutis Ž, Lukočius R, Girdenis V, et al.A measurement method of power transferred to an electric vehicle using wireless charging[J]. Sensors, 2023, 23(24): 9636. [11] Zhu Guodong, Gao Dawei.High-frequency voltage and current sense circuits for inductive power transfer systems[J]. IEEE Transactions on Power Electronics, 2020, 35(11): 11352-11362. [12] 袁瑞铭, 姜振宇, 易忠林, 等. 电动汽车无线充电电能计量关键技术研究与探讨[J]. 电测与仪表, 2018, 55(增刊1): 11-16. Yuan Ruiming, Jiang Zhenyu, Yi Zhonglin, et al.Research and discussion on key technologies of wireless charging electric energy metering for electric vehicles[J]. Electrical Measurement & Instrumentation, 2018, 55(S1): 11-16. [13] Jiang Zhenyu, Zhao Sixiang, Yuan Ruiming, et al.Research on the transmitting end billing mode and the receiving end billing mode for wirelessly charged electric vehicles[J]. Journal of Physics: Conference Series, 2019, 1176: 062035. [14] Chu S Y, Cui Xiaofan, Zan Xin, et al.Transfer-power measurement using a non-contact method for fair and accurate metering of wireless power transfer in electric vehicles[J]. IEEE Transactions on Power Electronics, 2022, 37(2): 1244-1271. [15] 张献, 邢子瑶, 薛明, 等. 无线电能传输系统异物检测技术研究综述[J]. 电工技术学报, 2022, 37(4): 793-807. Zhang Xian, Xing Ziyao, Xue Ming, et al.Overview of foreign object detection in wireless power transfer system[J]. Transactions of China Electrotechnical Society, 2022, 37(4): 793-807. [16] Cheng Bo, Lu Jianghua, Zhang Yiming, et al.A metal object detection system with multilayer detection coil layouts for electric vehicle wireless charging[J]. Energies, 2020, 13(11): 2960. [17] 张彬, 朱翀, 张希. 电动汽车无线充电系统金属异物检测灵敏度优化方法[J]. 电源学报, 2024, 22(4): 209-218. Zhang Bin, Zhu Chong, Zhang Xi.Sensitivity optimization method for metal object detection in electric vehicle wireless charging system[J]. Journal of Power Supply, 2024, 22(4): 209-218. [18] Zhang Ruihong, Yao Huawen, Li Jinyu, et al.A coordinate positioning technique based on region partitioning for EV wireless charging system[J]. IEEE Transactions on Industrial Electronics, 2024, 71(3): 2443-2453. [19] 项飞, 钟文兴. 基于垂直解耦线圈组的WPT系统金属异物检测方法[J/OL]. 电源学报, 1-12[2025-03-07]. http://kns.cnki.net/kcms/detail/12.1420.TM.20230628.1332.002.html. Xiang Fei, Zhong Wenxing. Metal foreign object detection method for WPT system based on vertical decoupling coil group[J/OL]. Journal of Power Supply, 1-12[2025-03-07]. http://kns.cnki.net/kcms/detail/12.1420.TM.20230628.1332.002.html. [20] 苏文博, 王维, 吕晓飞, 等. 含金属异物的无线充电系统场域等效建模分析[J]. 电力工程技术, 2023, 42(3): 226-232, 249. Su Wenbo, Wang Wei, Lü Xiaofei, et al.Equivalent modeling analysis of wireless charging system field containing metal foreign objects[J]. Electric Power Engineering Technology, 2023, 42(3): 226-232, 249. [21] 钟文兴, 张波. 电动汽车无线充电技术专辑主编述评[J]. 电源学报, 2022, 20(6): 1-3. Zhong Wenxing, Zhang Bo.Editorial for the special issue on EV wireless charging technology[J]. Journal of Power Supply, 2022, 20(6): 1-3. [22] Feng Hao, Tavakoli R, Onar O C, et al.Advances in high-power wireless charging systems: overview and design considerations[J]. IEEE Transactions on Transportation Electrification, 2020, 6(3): 886-919. [23] 吴理豪, 张波. 电动汽车静态无线充电技术研究综述(下篇)[J]. 电工技术学报, 2020, 35(8): 1662-1678. Wu Lihao, Zhang Bo.Overview of static wireless charging technology for electric vehicles: part Ⅱ[J]. Transactions of China Electrotechnical Society, 2020, 35(8): 1662-1678. [24] Wireless power transfer for light-duty plug-in/electric vehicles and alignment methodology:J2954_ 202208[S]. SAE International, 2022. [25] 钱尧, 孙运全, 朱伟. 基于双边LCC拓扑结构的无线充电系统集成线圈设计研究[J]. 电测与仪表, 2023, 60(10): 55-60. Qian Yao, Sun Yunquan, Zhu Wei.Design of inte-grated coil for EV wireless charging systems based on bilateral LCC topology[J]. Electrical Measurement & Instrumentation, 2023, 60(10): 55-60. [26] Delgado A, Salinas G, Oliver J A, et al.Equivalent conductor layer for fast 3-D finite element simu-lations of inductive power transfer coils[J]. IEEE Transactions on Power Electronics, 2020, 35(6): 6221-6230. [27] 国家市场监督管理总局, 国家标准化管理委员会. 电测量设备(交流) 特殊要求第21部分: 静止式有功电能表: GB/T 17215.321-2021[S]. 北京: 中国标准出版社, 2021. [28] 范兴明, 封浩, 张鑫. 最小二乘算法优化及其在锂离子电池参数辨识中的应用[J]. 电工技术学报, 2024, 39(5): 1577-1588. Fan Xingming, Feng Hao, Zhang Xin.Optimization of least squares method and its application in parameter identification of lithium-ion battery model[J]. Transa-ctions of China Electrotechnical Society, 2024, 39(5): 1577-1588. [29] 王雪平, 林甲祥, 巫建伟, 等. 基于可决系数的自适应关联规则挖掘算法[J]. 智能系统学报, 2020, 15(2): 352-359. Wang Xueping, Lin Jiaxiang, Wu Jianwei, et al.Adaptive-association-rule mining algorithm based on determination coefficient[J]. CAAI Transactions on Intelligent Systems, 2020, 15(2): 352-359. [30] 黄文聪, 饶天彪, 蒋煊焱, 等. 无线电能传输系统最大效率追踪及恒压输出复合控制方法[J]. 电工技术学报, 2024, 39(12): 3589-3601, 3615. Huang Wencong, Rao Tianbiao, Jiang Xuanyan, et al.Maximum efficiency tracking and constant voltage output compound control method for wireless power transfer system[J]. Transactions of China Electro-technical Society, 2024, 39(12): 3589-3601, 3615. [31] 杨阳, 王澍, 颜黎明, 等. 电动汽车无线充电系统双边LCC型谐振补偿网络及电磁安全性研究[J]. 西安交通大学学报, 2021, 55(5): 171-180. Yang Yang, Wang Shu, Yan Liming, et al.Research on double-sided LCC resonant topology and electromagnetic safety for wireless charging system of electric vehicles[J]. Journal of Xi’an Jiaotong University, 2021, 55(5): 171-180.
2025, Vol. 40 
