Study on Electrical Properties of Zinc Oxide-Polytetrafluoroethylene-Based Composite Ceramic Materials by Cold Sintering Process
Hou Xinyuan1, Xiao Yongjian1, Yang Yang1, Ren Chengjun2, Zhao Xuetong1
1. State Key Laboratory of Power Transmission Equipment Technology Chongqing University Chongqing 400044 China 2. Southwest Branch State Grid Corporation of China Chengdu 610041 China
Abstract：ZnO-based functional ceramics are widely used in the fields of varistor, thermistor, and gas-sensing. However, the temperature required for the preparation of ZnO-based functional ceramic is still high (>1 000℃). As a result, the additives that lead to modulating the properties of ceramic materials are limited to inorganic fillers. Conventional sintering leads to excessive growth of ZnO grains, which makes it difficult to achieve the miniaturization requirements of ZnO-based functional ceramic devices. Cold sintering process (CSP) enables the densification of ceramic materials at temperatures of below 300°C, thus providing the possibility for grain boundary engineering using ceramic materials as the matrix with organic polymer fillers or organic/inorganic composite fillers. In this paper, zinc oxide (ZnO)-polytetrafluoroethylene (PTFE)-based ceramic composites were prepared by CSP. Based on the above cold sintering conditions, high-density (>97%) ZnO-PTFE composite ceramics were prepared with ZnO as the matrix and polytetrafluoroethylene (PTFE) as the filler. The electrical properties of the ZnO-PTFE specimens showed better non-ohmic characteristics at the polymer content of 15%, the breakdown field and nonlinear coefficient of the composites can reach 933.68 V/mm and 5.74. The breakdown field is 6.92 times higher than the classical five-element formulation of ZnO varistor (135 V/mm), but the nonlinear coefficient is low. Microstructure observation and impedance performance testing showed that the PTFE phase limits the grain growth and increases the ceramic grain boundary impedance. PTFE at grain boundaries can induce the formation of varistor properties of ZnO-based composite ceramics, and improve the flexibility of ZnO ceramics. Further, the effects of metal oxides and PTFE on the microstructures and electrical properties of ZnO-PTFE based composites were investigated. The results indicate that a high relative density of over 97% was achieved for ZnO-PTFE-based composites doped with PTFE or co-doped with PTFE and metal oxides (CoO, Mn2O3). It is found that the electrical properties of ZnO-PTFE-based composites were significantly enhanced with the co-doping of PTFE, CoO, and Mn2O3. Specifically, the breakdown field and nonlinear coefficient of the composites were improved to 3 555.56 V/mm and 13.55, respectively. The J-E results show that the electrical conduction of the ceramic composites were dominated by the thermionic field emission at grain boundary. Moreover, the elastic modulus of the ceramic composites decreases greatly with the addition of PTFE and then increases after doping metal oxides (CoO, Mn2O3). This study demonstrates that CSP provides a new route to fabricate ceramic-polymer-based composites and modulate their properties.
[1] 孟鹏飞, 郭敬科, 张恒志, 等. ZnO压敏电阻微观结构参数与宏观电气性能的关联机制[J]. 电工技术学报, 2024, 39(5): 1454-1463. Meng Pengfei, Guo Jingke, Zhang Hengzhi, et al.The correlation mechanism that micro-structure parameters of ZnO varistor to the macroscopic electrical characteristics[J]. Transactions of China Electrotechnical Society, 2024, 39(5): 1454-1463. [2] Cherumannil Karumuthil S, Singh K, Valiyaneerilakkal U, et al.Fabrication of poly(vinylidene fluoride-trifluoroethylene)-zinc oxide based piezoelectric pressure sensor[J]. Sensors and Actuators A: Physical, 2020, 303: 111677. [3] 李海涛, 鞠平, 须雷, 等. 一种高可靠性智能型避雷器在线监测系统的设计[J]. 电力工程技术, 2019, 38(4): 159-164. Li Haitao, Ju Ping, Xu Lei, et al.Design of a high reliable intelligent on-line monitoring system for metal oxide arrester[J]. Electric Power Engineering Technology, 2019, 38(4): 159-164. [4] 王继来, 王朋成, 张威振, 等. 隧道牵引分区所雷击暂态特性及其二次设备电磁兼容研究[J]. 高压电器, 2024, 60(1): 108-117. Wang Jilai, Wang Pengcheng, Zhang Weizhen, et al.Study on lightning transient characteristic of tunnel traction sectioning post and electromagnetic compatibility of its secondary equipment[J]. High Voltage Apparatus, 2024, 60(1): 108-117. [5] 谢从珍, 李彦丞, 杜岩, 等. 基于磁流体动力学的35 kV自脱离防雷装置灭弧仿真[J]. 电力工程技术, 2023, 42(1): 61-69. Xie Congzhen, Li Yancheng, Du Yan, et al.Simulation research on arc extinguishing characteristics of 35 kV self-detaching lightning protection device based on magnetohydrodynamics[J]. Electric Power Engineering Technology, 2023, 42(1): 61-69. [6] Matsuoka M.Nonohmic properties of zinc oxide ceramics[J]. Japanese Journal of Applied Physics, 1971, 10(6): 736. [7] Badev A, Marinel S, Heuguet R, et al.Sintering behavior and non-linear properties of ZnO varistors processed in microwave electric and magnetic fields at 2.45GHz[J]. Acta Materialia, 2013, 61(20): 7849-7858. [8] Bernik S.Low-temperature sintering of ZnO-Bi2O3-based varistor ceramics for enhanced microstructure development and current-voltage characteristics[J]. Ceramics - Silikaty, 2018, 62(1): 8-14. [9] Beynet Y, Izoulet A, Guillemet-Fritsch S, et al.ZnO-based varistors prepared by spark plasma sintering[J]. Journal of the European Ceramic Society, 2015, 35(4): 1199-1208. [10] Wu Angxuan, Zhu Zhixiang, Wang Xilin, et al.High-performance ZnO varistor ceramics prepared by arc-induced flash sintering with low energy consumption at room temperature[J]. High Voltage, 2022, 7(2): 222-232. [11] Liu Wenfeng, Zhang Lei, Kong Fanyi, et al.Enhanced voltage gradient and energy absorption capability in ZnO varistor ceramics by using nano-sized ZnO powders[J]. Journal of Alloys and Compounds, 2020, 828: 154252. [12] 崔秀琪, 杨方兴, 滕雅娣. SiAlCN型PDC陶瓷的研究进展[J]. 现代技术陶瓷, 2022, 43(3): 173-186. Cui Xiuqi, Yang Fangxing, Teng Yadi.Research progress of SiAlCN PDC ceramics[J]. Advanced Ceramics, 2022, 43(3): 173-186. [13] Takano Y, Takeya H, Fujii H, et al.Superconducting properties of MgB2 bulk materials prepared by high-pressure sintering[J]. Applied Physics Letters, 2001, 78(19): 2914-2916. [14] Valdez-Nava Z, Guillemet-Fritsch S, Tenailleau C, et al.Colossal dielectric permittivity of BaTiO3-based nanocrystalline ceramics sintered by spark plasma sintering[J]. Journal of Electroceramics, 2009, 22(1): 238-244. [15] Zhao Zhe, Buscaglia V, Bowen P, et al. Spark plasma sintering of nano-crystalline ceramics[J]. Key Engineering Materials, 2004, 264-268: 2297-2300. [16] Katz J D.Microwave sintering of ceramics[J]. Annual Review of Materials Science, 1992, 22: 153-170. [17] Chen I W, Wang X H.Sintering dense nanocrystalline ceramics without final-stage grain growth[J]. Nature, 2000, 404(6774): 168-171. [18] Guo Jing, Guo Hanzheng, Baker A L, et al.Cold sintering: a paradigm shift for processing and integration of ceramics[J]. Angewandte Chemie (International Ed in English), 2016, 55(38): 11457-11461. [19] 陆雪萍, 陆晓芳, 范宇驰, 等. n型Bi2Te2.7Se0.3热电材料的冷烧结制备及其性能研究[J]. 现代技术陶瓷, 2023, 44(1): 67-76. Lu Xueping, Lu Xiaofang, Fan Yuchi, et al.Thermoelectric properties of cold sintered n-type Bi2Te2.7Se0.3[J]. Advanced Ceramics, 2023, 44(1): 67-76. [20] 康晟淋, 赵学童, 张洁心, 等. 冷烧结技术的研究进展及其在电工领域的潜在应用[J]. 电工技术学报, 2022, 37(5): 1098-1114. Kang Shenglin, Zhao Xuetong, Zhang Jiexin, et al.Recent research progress of cold sintering process and its potential application in electrotechnical fields[J]. Transactions of China Electrotechnical Society, 2022, 37(5): 1098-1114. [21] Ndayishimiye A, Tsuji K, Wang Ke, et al.Sintering mechanisms and dielectric properties of cold sintered (1-x)SiO2-xPTFE composites[J]. Journal of the European Ceramic Society, 2019, 39(15): 4743-4751. [22] Ndayishimiye A, Grady Z A, Tsuji K, et al.Thermosetting polymers in cold sintering: the fabrication of ZnO-polydimethylsiloxane composites[J]. Journal of the American Ceramic Society, 2020, 103(5): 3039-3050. [23] Si Mingming, Hao Jianyu, Zhao Enda, et al.Preparation of zinc oxide/poly-ether-ether-ketone (PEEK) composites via the cold sintering process[J]. Acta Materialia, 2021, 215: 117036. [24] Hérisson de Beauvoir T, Tsuji K, Zhao Xuetong, et al. Cold sintering of ZnO-PTFE: utilizing polymer phase to promote ceramic anisotropic grain growth[J]. Acta Materialia, 2020, 186: 511-516. [25] Mena-Garcia J, Dursun S, Tsuji K, et al.Integration and characterization of a ferroelectric polymer PVDF-TrFE into the grain boundary structure of ZnO via cold sintering[J]. Journal of the European Ceramic Society, 2022, 42(6): 2789-2797. [26] Si Mingming, Guo Jing, Hao Jianyu, et al.Cold sintered composites consisting of PEEK and metal oxides with improved electrical properties via the hybrid interfaces[J]. Composites Part B: Engineering, 2021, 226: 109349. [27] Vinoth S, Wang S F.Cold sintering process for a BaTiO3/poly(vinylidene difluoride) ceramic-polymer composite: evaluation of the structural and microwave dielectric properties[J]. Inorganic Chemistry, 2023, 62(21): 8326-8333. [28] 冯宇, 程伟晔, 岳东, 等. 含有氮化硼势垒层的三明治结构聚合物基复合介质储能特性研究[J]. 电工技术学报, 2024, 39(1): 121-134. Feng Yu, Cheng Weiye, Yue Dong, et al.Energy storage performance of sandwich structure polymer-based composite dielectric with boron nitride barrier layer[J]. Transactions of China Electrotechnical Society, 2024, 39(1): 121-134. [29] 董冰冰, 孟岩, 郭志远. 气体间隙开关触发失效分析及寿命提升方法[J]. 电工技术学报, 2025, 40(1): 264-272. Dong Bingbing, Meng Yan, Guo Zhiyuan.Trigger failure analysis and life extension methods of gas gap switch[J]. Transactions of China Electrotechnical Society, 2025, 40(1): 264-272. [30] Sada Takao, Tsuji K, Ndayishimiye A, et al.High permittivity BaTiO3 and BaTiO3-polymer nanocomposites enabled by cold sintering with a new transient chemistry: Ba(OH)2∙8H2O[J]. Journal of the European Ceramic Society, 2021, 41(1): 409-417. [31] 邓凯. 钛酸铜钙巨介电性能掺杂改性实验研究[D].成都: 电子科技大学, 2018. Deng Kai.Experimental study on doping performance modification of CaCu3Ti4O12 giant dielectrics[J]. Chengdu: University of Electronic Science and Technology of China, 2018. [32] 何俊佳, 宋丽, 周本正, 等. ZnO压敏电阻微观结构调控与性能提升研究综述[J]. 电工技术学报, 2023, 38(20): 5605-5619. He Junjia, Song Li, Zhou Benzheng, et al.Review on microstructure control and performance improvement of ZnO varistors[J]. Transactions of China Electro-technical Society, 2023, 38(20): 5605-5619. [33] Arshad M, Ahmed A S, Azam A, et al.Exploring the dielectric behavior of Co doped ZnO nanoparticles synthesized by wet chemical route using impedance spectroscopy[J]. Journal of Alloys and Compounds, 2013, 577: 469-474. [34] Han J, Mantas P Q, Senos A M R. Grain growth in Mn-doped ZnO[J]. Journal of the European Ceramic Society, 2000, 20(16): 2753-2758. [35] 牛舒楠, 郑丽君, 罗旭东, 等. Al2O3-SiC复合陶瓷材料的研究进展[J]. 现代技术陶瓷, 2024, 45(3): 231-246. Niu Shunan, Zheng Lijun, Luo Xudong, et al.Research progress of Al2O3-SiC composite ceramics[J]. Advanced Ceramics, 2024, 45(3): 231-246. [36] Evans A G.Structural reliability: a processing-dependent phenomenon[J]. Journal of the American Ceramic Society, 1982, 65(3): 127-137.
2025, Vol. 40 
