The Key Dielectric Properties and Performance Evaluation Method of High-Density Pressboard for Electrical Purposes
Gao Chunjia1, Qi Bo1, Li Chengrong1, Lu Licheng2, Zhang Shuqi3
1. State Key Laboratory of Alternate Electrical Power System with Renewable Energy Sources North China Electric Power University Beijing 102206 China; 2. State Grid Corporation of China Beijing 100031 China; 3. China Electric Power Research Institute Beijing 100192 China
Abstract The high-density electrical pressboard, as the main insulating material for large-scale power equipment such as power/converter transformers, plays an important role in the safe and stable operation of power equipment and power grid systems. However, the high-density pressboard has practical problems, such as varying insulation properties among different types, lack of performance evaluation and selection method. This paper sets up a measurement platform for three key dielectric properties of electrical pressboard, namely the relative permittivity, volume resistivity and surface resistivity. Five kinds of pressboards come from five representative insulating material manufacturers at home and abroad were adopted as the test samples. The influence of external conditions such as temperature and water-content on the dielectric properties was analyzed, and the fitting quantitative relationship and the influencing mechanism were explained. The following conclusions can be drawn through the experimental results. ①With the increase of temperature and water-content of pressboard, the relative permittivity has an obvious increase with a maximum growth percentage of 55.85%. The relative permittivity of different pressboards is greatly affected by temperature or water-content, and the deviation is up to 22.05%. ②The higher the temperature or water-content of pressboard is, the lower the volume and surface resistivity of pressboard, and the maximum resistivity reduction can reach 98.25%. The difference of the resistivity among different pressboards affected by temperature and water-content can reach 94.32%. ③The dielectric properties among different batches of the same type of pressboard are significantly different. ④The test results of conventional physical and chemical properties of pressboard demonstrate the differences in dielectric properties between different types of pressboards. Finally, a performance evaluation method for the dielectric properties of pressboard was proposed. The dielectric properties of different insulating pressboard products were compared horizontally, which could provide data support and technical references for the design of insulation structure and the application selection of insulation materials.
Gao Chunjia,Qi Bo,Li Chengrong等. The Key Dielectric Properties and Performance Evaluation Method of High-Density Pressboard for Electrical Purposes[J]. Transactions of China Electrotechnical Society, 2020, 35(14): 3075-3086.
[1] 杜伯学, 朱闻博, 李进, 等. 换流变压器阀侧套管油纸绝缘研究现状[J]. 电工技术学报, 2019, 34(6): 1300-1309. Du Boxue, Zhu Wenbo, Li Jin, et al.Research status of oil-paper insulation for valve side bushing of converter transformer[J]. Transactions of China Elec- trotechnical Society, 2019, 34(6): 1300-1309. [2] 杨志淳, 沈煜, 杨帆, 等. 考虑多元因素态势演变的配电变压器迁移学习故障诊断模型[J]. 电工技术学报, 2019, 34(7): 1505-1515. Yang Zhichun, Shen Yu, Yang Fan, et al.A transfer learning fault diagnosis model of distribution trans- former considering multi-factor situation evolution[J]. Transactions of China Electrotechnical Society, 2019, 34(7): 1505-1515. [3] 张明泽, 刘骥, 齐朋帅, 等. 基于介电响应技术的变压器油纸绝缘含水率数值评估方法[J]. 电工技术学报, 2018, 33(18): 4397-4407. Zhang Mingze, Liu Ji, Qi Pengshuai, et al.Numerical evaluation method for moisture content of trans- former oil-paper insulation based on dielectric response technique[J]. Transactions of China Electro- technical Society, 2018, 33(18): 4397-4407. [4] 王建宁, 宣白云. 变压器绝缘纸板及出线装置等成型绝缘件国产化现状及展望[J]. 电工技术学报, 2011, 26(5): 192-198. Wang Jianning, Xuan Baiyun.Domestic situation and prospect of pressboards and outlet device insulation components[J]. Transactions of China Electro- technical Society, 2011, 26(5): 192-198. [5] 廖瑞金, 王季宇, 袁媛, 等. 换流变压器下新型纤维素绝缘纸特性综述[J]. 电工技术学报, 2016, 31(10): 1-15. Liao Ruijin, Wang Jiyu, Yuan Yuan, et al.Review on the characteristic of new cellulose insulation paper used in the converter transformer[J]. Transactions of China Electrotechnical Society, 2016, 31(10): 1-15. [6] 廖瑞金, 唐超, 杨丽君, 等. 电力变压器用绝缘纸热老化的微观结构及形貌研究[J]. 中国电机工程学报, 2007, 27(33): 59-64. Liao Ruijin, Tang Chao, Yang Lijun, et al.Research on the microstructure and morphology of power transformer insulation paper after thermal aging[J]. Proceedings of the CSEE, 2007, 27(33): 59-64. [7] 燕飞东. 特高压变压器用绝缘材料性能研究[D]. 济南: 山东大学, 2017. [8] 詹绪海, 于钦学, 刘光祺, 等. 变压器油体积电阻率随温度和电压变化的研究[C]//第十三届全国工程电介质学术会议, 西安, 中国, 2011: 303-306. [9] 陈庆国, 池明赫, 王刚, 等. 含水率对复合电场下油纸绝缘电场分布的影响[J]. 电机与控制学报, 2013, 17(7): 54-60. Chen Qingguo, Chi Minghe, Wang Gang, et al.Moisture influence on the electric field distribution of oil-pressboard insulation under compound electric field[J]. Electric Machines and Control, 2013, 17(7): 54-60. [10] 徐征宇, 程涣超, 遇心如, 等. 不同吸油率油浸纸板介电特性及电导特性研究[J]. 电机与控制学报, 2015, 19(12): 82-87. Xu Zhengyu, Cheng Huanchao, Yu Xinru, et al.Dielectric and conducive properties of oil-impregnated pressboard under different oil absorption[J]. Electric Machines and Control, 2015, 19(12): 82-87. [11] Blennow J, Ekanayake C, Walczak K, et al.Field experience with measurements of dielectric response in frequency domain for power transformer diag- nostics[J]. IEEE Transactions on Power Delivery, 2006, 21(2): 681-688. [12] Hasegawa T, Yamaji K.Dielectric strength of transformer insulation at DC polarity reversal[J]. IEEE Transactions on Power Delivery, 1997, 12(7): 1526-1531. [13] Tulasi Ram S S T, Kamaraju M, Singh B P. Flashover behaviour of converter transformer insulation sub- jected to superimposed ac and dc voltages[J]. Annals of Physical & Rehabilitation Medicine, 2012, 55(S1): e81. [14] Wen Kaicheng, Zhou Youbin, Fu Jun, et al.A calculation method and some features of transient field under polarity reversal voltage in HVDC insulation[J]. IEEE Transactions on Power Delivery, 1993, 8(1): 223-230. [15] 刘泽洪, 郭贤珊. 特高压变压器绝缘结构[J]. 高电压技术, 2010, 36(1): 7-12. Liu Zehong, Guo Xianshan.Insulation structure of UHV power translormer[J]. High Voltage Engineering, 2010, 36(1): 7-12. [16] Fofana I, Wasserberg V, Borsi H, et al.Challenge of mixed insulating liquids for use in high-voltage transformers. II. Investigations of mixed liquid impregnated paper insulation[J]. Electrical Insulation Magazine IEEE, 2002, 18(4): 5-16. [17] Koch, Kruger.Measuring and analyzing the dielectric response of power transformers[J]. High Voltage Engineering, 2009, 35(8): 1933-1939. [18] 张大宁, 刘孝为, 詹江杨, 等. 变压器油纸绝缘频域介电谱的虚部分析[J]. 电工技术学报, 2019, 34(4): 847-854. Zhang Daning, Liu Xiaowei, Zhan Jiangyang, et al.Analysis of imaginary part of frequency domain spectroscopy for oil-paper insulation transformer[J]. Transactions of China Electrotechnical Society, 2019, 34(4): 847-854. [19] GB/T 1409—2006 固体绝缘材料在工频、音频、高频下相对介电常数和介质损耗因数的测试方法[S]B/T 1409—2006 固体绝缘材料在工频、音频、高频下相对介电常数和介质损耗因数的测试方法[S]. 北京: 中国标准出版社, 2006. [20] GB/T 1410—2006 固体绝缘材料体积电阻率和表面电阻率试验方法[S]B/T 1410—2006 固体绝缘材料体积电阻率和表面电阻率试验方法[S]. 北京: 中国标准出版社, 2006. [21] IEC 60243—1: 2013 Electrical strength of insulating materials test methods Part 1: Tests at power frequencies[S]. IEC Standard Association, 2013. [22] 王伟, 周冰, 徐剑峰, 等. 油纸绝缘系统中含高水分绝缘纸板的沿面爬电特性[J]. 高电压技术, 2011, 37(8): 1924-1929. Wang Wei, Zhou Bing, Xu Jianfeng, et al.Creepage discharge performance of high moisture pressboard in oil-paper insulation system[J]. High Voltage Engineering, 2011, 37(8): 1924-1929. [23] 于会民, 王会娟, 张绮, 等. 变压器油纸绝缘体系中水分和气体含量研究[J]. 绝缘材料, 2019, 52(3): 86-90. Yu Huimin, Wang Huijuan, Zhang Qi, et al.Study on water and gas content in oil-paper insulation system of transformer[J]. Insulating Materials, 2019, 52(3): 86-90. [24] 赵建设. 高密度电工纸板水分迁移特性的研究[D]. 北京: 华北电力大学, 2018. [25] 池明赫. 运行条件对复合电场下油纸绝缘击穿特性的影响[D]. 哈尔滨: 哈尔滨理工大学, 2015. [26] 金维芳. 电介质物理学[M]. 2版. 北京: 科学出版社, 2003. [27] 周远翔, 沙彦超, 陈维江, 等. 变压器油与绝缘纸板电导特性研究[J]. 电网技术, 2013, 37(9): 2527-2533. Zhou Yuanxiang, Sha Yanchao, Chen Weijiang, et al.Conduction characteristics in transformer oil and electrical insulation paper[J]. Power System Techno- logy, 2013, 37(9): 2527-2533. [28] 鲁莽, 李亚飞, 何清, 等. 水分对植物绝缘油浸纸板击穿特性的影响[J]. 绝缘材料, 2018, 51(4): 12-17. Lu Mang, Li Yafei, He Qing, et al.Effect of moisture on breakdown characteristics of vegetable insulating oil-impregnated pressboard[J]. Insulating Materials, 2018, 51(4): 12-17. [29] 甄东. 基于理化特性和介电特性的高密度绝缘纸板性能评价方法[D]. 北京: 华北电力大学, 2018. [30] 张欲晓, 李胜利, 王梦君, 等. 变压器绝缘纸的聚合度变化规律[J]. 高电压技术, 2011, 37(10): 2458-2463. Zhang Yuxiao, Li Shengli, Wang Mengjun, et al.Degree of polymerization of insulation paper in the transformer[J]. High Voltage Engineering, 2011, 37(10): 2458-2463. [31] GB/T 19264.3—2013 电气用压纸板和薄纸板[S]. 北京:中国标准出版社, 2013. [32] GB/T 450—2008 纸和纸板试样的采取及试样纵横向、正反面的测定[S]GB/T 450—2008 纸和纸板试样的采取及试样纵横向、正反面的测定[S]. 北京: 中国标准出版社, 2008. [33] GB/T 462—2008 纸、纸板和纸浆分析试样水分的测定[S]GB/T 462—2008 纸、纸板和纸浆分析试样水分的测定[S]. 北京: 中国标准出版社, 2008. [34] GB/T 451B/T 451.2—2002 纸和纸板定量的测定[S]. 北京: 中国标准出版社, 2002. [35] GB/T 1548—2016 纸浆铜乙二胺(CED)溶液中特性粘度值的测定[S]B/T 1548—2016 纸浆铜乙二胺(CED)溶液中特性粘度值的测定[S]. 北京: 中国标准出版社, 2016. [36] GB/T 29305—2012 新的和老化后的纤维素电气绝缘材料粘均聚合度的测量[S]B/T 29305—2012 新的和老化后的纤维素电气绝缘材料粘均聚合度的测量[S]. 北京: 中国标准出版社, 2012. [37] 宋玉侠, 罗传勇, 阎雪梅, 等. 粘度法测定电工用纸/纸板聚合度的研究及应用[J]. 绝缘材料, 2012, 45(1): 65-68. Song Yuxia, Luo Chuanyong, Yan Xuemei, et al.Measurement of polymerization degree of paper/ paperboard by viscometry for electrical engin- eering[J]. Insulating Materials, 2012, 45(1): 65-68. [38] 张天云. 工程材料综合评价系统研究与实现[D]. 兰州: 兰州理工大学, 2008. [39] 张天云, 杨瑞成, 陈奎. 基于层次分析法确定工程材料评价指标的权重[J]. 兰州理工大学学报, 2007, 33(2): 17-19. Zhang Tianyun, Yang Ruicheng, Chen Kui.Deter- mination of weighing values for assessment indexes of engineering materials based on analytic hierarchy procedure[J]. Journal of Lanzhou University of Technology, 2007, 33(2): 17-19.
2020, Vol. 35 
