电工技术学报
论文 |
特高压交流GIS/GIL拔孔型陷阱优化设计与协同布置方法研究
耿秋钰1, 胡智莹1, 李庆民1, 庄添鑫2, 刘焱3
1.华北电力大学新能源电力系统国家重点实验室 北京 102206;
2.江苏电力科学研究院 南京 210036;
3.中国电力科学研究院 北京 100192
Research on Optimal Design and Synergism Arrangement Methodology of Convex-Shaped Traps for Ultra High Voltage AC GIS/GIL Applications
Geng Qiuyu1, Hu Zhiying1, Li Qingmin1, Zhuang Tianxin2, Liu Yan3
1. State Key Laboratory of Alternate Electrical Power System with Renewable Energy Sources North China Electric Power University Beijing 102206 China;
2. Jiangsu Electric Power Research Institute Nanjing 210036 China;
3. China Electric Power Research Institute Beijing 100192 China
全文: PDF (1663 KB)  
输出: BibTeX | EndNote (RIS)      
摘要 

交流气体绝缘组合电器和输电管道内的运动金属微粒是诱发设备绝缘故障的重要因素,且在特高压下的运动金属微粒引发设备绝缘故障的概率更大,而微粒陷阱可抑制金属微粒的运动,但实际工程中的微粒陷阱仍缺乏主动捕获微粒的能力。该文首先基于GIS/GIL内金属微粒动力学模型,分析了拔孔型陷阱的微粒主动捕获机制。进而根据金属微粒荷电运动与碰撞动力学特性,建立了拔孔型陷阱捕获概率计算模型,考虑陷阱的捕获能力对拔孔型陷阱的结构参数进行优化设计。具体结果表明,针对苏通工程中交流1 000 kV GIL,当陷阱直径为60 cm、深度为30 cm时,拔孔型陷阱抑制微粒效果达到最佳。进一步考虑微粒碰撞反射角的随机性,将拔孔型陷阱附近捕获率大于90%的区域定义为有效捕获范围,优化的拔孔型陷阱的有效捕获范围为32 cm。最后,通过分析栅格型陷阱与拔孔型陷阱轴向电场分布,表明栅格型陷阱能够增强拔孔型陷阱的有效捕获范围,并以提高绝缘子附近的微粒抑制效果为目标,提出了绝缘子附近栅格型与拔孔型陷阱的协同布置方法。

服务
把本文推荐给朋友
加入我的书架
加入引用管理器
E-mail Alert
RSS
作者相关文章
耿秋钰
胡智莹
李庆民
庄添鑫
刘焱
关键词 特高压GIS/GIL拔孔型陷阱栅格型陷阱优化设计协同布置方法    
Abstract

AC gas insulated switchgear and transmission lines faces critical insulation failure challenges caused by metal particles inside, and the probability of insulation failure caused by metal particles under UHV increases. However, the particle traps in practical engineering, the key devices available to inhibit the movement of particles, lack the ability to proactively capture particles. Firstly, in this paper, the proactively capture particle mechanism of the convex-shaped trap is analyzed basing on the dynamic model of metal particle in GIS/GIL.
By analyzing the force of particles and the axial electric field distribution of the convex-shaped trap, this paper considers that the axial electric field distribution near the convex-shaped traps is an important factor leading to the active trapping of metal particles. The external voltage is applied to the starting voltage. Considering the applied voltage is AC voltage, the initial time should be set. Due to the electrostatic induction, the metal particles are negatively charged, and the metal particles on both sides of the trap move towards the trap direction. At the same time, the maximum movement height of the trapped particles under AC voltage is 2-8 cm, so the particles inside the trap cannot escape the trap. Based on the force analysis of particles, it can not only analyze the active capture mechanism of the convex-shaped trap, but also provide a theoretical basis for the subsequent establishment of the capture range calculation model of the convex-shaped trap. On this basis, this paper realizes the performance test and optimization design of the convex-shaped trap.
According to the charged motion and collision dynamics characteristics of metal particles, the model for calculating the capture probability of the convex-shaped trap is established, and the structural parameters of the convex-shaped trap should be optimized considering the capture ability of trap. The results illustrate when the diameter of trap is 60 cm and the depth of trap is 30 cm in the 1000 kV GIS/GIL of Sutong GIL Comprehensive Pipe Corridor, the particle suppression effect of the convex-shaped trap is optimal. Further, the area near the convex-shaped trap with capture rate over 90 % is defined as the effective capture range considering the randomness of particle collision reflection angle, and the effective capture range of the convex-shaped trap reaches 32 cm. In this paper, a general optimization design method for convex-shaped traps is proposed, which is also suiTab.for optimizing other voltage levels of convex-shaped traps.
Finally, by analyzing the axial electric field distribution of the grid trap and the convex-shaped trap, it is shown that the grid trap can enhance the effective capture range of the convex-shaped trap. To improve the particle suppression effect near the insulator, a synergism arrangement methodology of the grid trap and the convex-shaped trap near the convex surface of basin insulator is proposed.
The grid trap can effectively suppress the metal particles below the insulator. Since the grid trap can increase the capture range of the convex-shaped trap, the convex-shaped trap can be arranged far from the insulator. By optimizing the synergism arrangement of two traps, defining the optimal arrangement methodology. Length of the grid trap arranged near the insulator cannot be less than 40 cm, and the effective capture range of the convex-shaped trap matched with it reaches up to 65 cm. The protection range of the trap combination for insulators can reach up to 225 cm. Based on the theoretical analysis, the trap combination can not only effectively protect the basin insulator, but also improve the insulation level of the three-pillar insulator.
In this paper, the theoretical analysis about the active capture mechanism of the convex-shaped traps, the design scheme of the convex-shaped traps for UHV GIS/GIL and the synergism arrangement methodology of the grid and convex-shaped traps are proposed. This methodology provides a reliable technical mean for capturing the metal particles in UHV GIS / GIL.

Key wordsUltra High Voltage    GIS/GIL    convex-shaped trap    grid trap    optimal design    synergism arrangement methodology   
收稿日期: 2022-09-01     
PACS: TM85  
基金资助:

国家电网有限公司科技项目资助(5500-202155109A-0-0-00)

通讯作者: 李庆民 男,1968年生,教授,博士生导师,研究方向为高电压与绝缘技术、放电物理等。E-mail:lqmeee@ncepu.edu.cn   
作者简介: 耿秋钰 男,1998年生,硕士研究生,研究方向为气体绝缘输电管道微粒运动、放电与抑制。E-mail:gengqiuyu19981123@163.com
引用本文:   
耿秋钰, 胡智莹, 李庆民, 庄添鑫, 刘焱. 特高压交流GIS/GIL拔孔型陷阱优化设计与协同布置方法研究[J]. 电工技术学报, 0, (): 221680-221680. Geng Qiuyu, Hu Zhiying, Li Qingmin, Zhuang Tianxin, Liu Yan. Research on Optimal Design and Synergism Arrangement Methodology of Convex-Shaped Traps for Ultra High Voltage AC GIS/GIL Applications. Transactions of China Electrotechnical Society, 0, (): 221680-221680.
链接本文:  
https://dgjsxb.ces-transaction.com/CN/10.19595/j.cnki.1000-6753.tces.221680          https://dgjsxb.ces-transaction.com/CN/Y0/V/I/221680