Optimization of Insulation Material Performance Parameters for Medium Frequency Transformers Based on Thermosolid Coupling
Zhao Yushun1, Dai Yixian1, Zhuang Jiacai2, Cai Guoqing2, Chen Zhiwei1, Liu Xin1,3
1. School of Electrical Engineering and Automation Hefei University of Technology Hefei 230009 China; 2. Sungrow Power Supply Co. Ltd Hefei 230088 China; 3. State Grid Anhui Electric Power Co. Ltd Hefei 230061 China
Abstract:Power electronic transformers are the core equipment in the future smart grid and energy internet. In order to meet the needs of the grid, the voltage level of power electronic transformers will be increased to 35 kV, and the capacity will also reach 200 MW and above. Working in a high frequency, high voltage, and high temperature environment, the core component of a power electronic transformer, a medium frequency (MF) transformer, becomes the weakest link. Insulation of MF-transformers by casting epoxy resin is one of the most competitive solutions with small size, maintenance-free, clean, and environmentally friendly. However, there are still some problems with epoxy resin casting, such as heat dissipation difficulties, partial discharge, and insulation cracking. This paper optimizes the performance parameters of the insulation materials to match to improve the heat dissipation and mechanical performance of the MF-transformer. Firstly, a finite element model of resin-cast MF-transformer with forced air cooling is built in COMSOL. Simulations were performed according to the requirements of the transformer temperature rise test and thermal shock test. The temperature field during the rated operation and the stress field and displacement field during the thermal shock test were analyzed, and evaluation indexes were given according to the characteristics of insulation materials. The glass transition temperature of epoxy resin is generally lower than the permissible temperature of its heat-resistant grade. Thus, the glass transition temperature is used as the standard for evaluating the temperature rise of resin-cast IF transformers. In addition, the stress of the insulation layer in the thermal shock test needs to be less than the tensile strength of epoxy resin, and the offset of the insulation layer needs to be less than the elongation at the break of epoxy resin. The simulation results show that the pure epoxy resin cannot meet the temperature rise of the transformer in rated operation and the stress requirements in the thermal shock test. Then, the influence of insulation material performance and parameters on transformer temperature rise, stress, and deformation are investigated using Box-Benhnken central combined design tests and response surface analysis. The response surface model is solved when the temperature rise and stress requirements of the medium frequency transformer are met. The ideal range of insulation material performance parameters is obtained, and the optimized fit scheme is determined combined with the actual: thermal conductivity of 0.8 W·(m·K)-1, thermal expansion coefficient of 4.7×10-5 K-1, and Young's modulus of 3.5 GPa. By optimizing the fit of the parameters of the insulation material, the thermal and mechanical performance of the MF-transformer can be significantly improved. Compared with the pure epoxy resin, the optimized MF-transformer has 82.6 % lower maximum temperature rise, 37.7 % lower maximum stress, and 40.2 % lower maximum deformation, and all index levels meet the requirements. After applying the results of parameter optimization to a prototype MF-transformer, it successfully passed the temperature rise test and thermal shock test, which verified the rationality and reliability of the optimization of the insulation material parameters.
赵玉顺, 戴义贤, 庄加才, 蔡国庆, 陈志伟, 刘鑫. 基于热固耦合的中频变压器绝缘材料性能参数优化配合方法[J]. 电工技术学报, 2023, 38(4): 1051-1063.
Zhao Yushun, Dai Yixian, Zhuang Jiacai, Cai Guoqing, Chen Zhiwei, Liu Xin. Optimization of Insulation Material Performance Parameters for Medium Frequency Transformers Based on Thermosolid Coupling. Transactions of China Electrotechnical Society, 2023, 38(4): 1051-1063.
[1] 胡钰杰, 李子欣, 罗龙, 等. 串联谐振间接矩阵型电力电子变压器高频电流特性分析及开关频率设计[J]. 电工技术学报, 2022, 37(6): 1442-1454. Hu Yujie, Li Zixin, Luo Long, et al.Characteristic analysis of high-frequency-link current of series resonant indirect matrix type power electronics transformer and switching frequency design[J]. Transactions of China Electrotechnical Society, 2022, 37(6): 1442-1454. [2] 袁立强, 高深, 姬世奇, 等. 基于占空比同步的电力电子变压器低压交流端口模式切换控制[J]. 电工技术学报, 2022, 37(3): 729-738. Yuan Liqiang, Gao Shen, Ji Shiqi, et al.Mode transition for low voltage AC port of power electronic transformers based on duty cycle synchronization[J]. Transactions of China Electrotechnical Society, 2022, 37(3): 729-738. [3] Forouzesh M, Siwakoti Y P, Gorji S A, et al.Step-up DC-DC converters: a comprehensive review of voltage-boosting techniques, topologies, and applications[J]. IEEE Transactions on Power Electronics, 2017, 32(12): 9143-9178. [4] 高范强, 李子欣, 李耀华, 等. 面向交直流混合配电应用的10kV-3MV·A四端口电力电子变压器[J]. 电工技术学报, 2021, 36(16): 3331-3341. Gao Fanqiang, Li Zixin, Li Yaohua, et al.10kV-3MV·A four-port power electronic transformer for AC-DC hybrid power distribution applications[J]. Transa-ctions of China Electrotechnical Society, 2021, 36(16): 3331-3341. [5] 李子欣, 高范强, 赵聪, 等. 电力电子变压器技术研究综述[J]. 中国电机工程学报, 2018, 38(5): 1274-1289. Li Zixin, Gao Fanqiang, Zhao Cong, et al.Research review of power electronic transformer techno-logies[J]. Proceedings of the CSEE, 2018, 38(5): 1274-1289. [6] 杨景刚, 张珂, 陈武, 等. 大功率中频变压器研究综述[J]. 电源学报, 2020, 18(1): 4-17. Yang Jinggang, Zhang Ke, Chen Wu, et al.Review on researches of high-power medium-frequency trans-former[J]. Journal of Power Supply, 2020, 18(1): 4-17. [7] Tuncer E, Sauers I, James D R, et al.Electrical insulation characteristics of glass fiber reinforced resins[J]. IEEE Transactions on Applied Super-conductivity, 2009, 19(3): 2359-2362. [8] Mirza A, Chen Weiqiang, Nguyen H, et al.High-voltage high-frequency testing for medium-voltage motor insulation degradation[C]//2018 IEEE Energy Conversion Congress and Exposition (ECCE), Portland, OR, USA, 2018: 2444-2447. [9] 王威望, 刘莹, 何杰峰, 等. 高压大容量电力电子变压器中高频变压器研究现状和发展趋势[J]. 高电压技术, 2020, 46(10): 3362-3373. Wang Weiwang, Liu Ying, He Jiefeng, et al.Research status and development of high frequency transformer used in high voltage and large capacity power electronic transformer[J]. High Voltage Engineering, 2020, 46(10): 3362-3373. [10] 王佳宁, 邹强, 胡嘉汶, 等. 一种中压绝缘大功率中频变压器的优化设计方法[J]. 电工技术学报, 2022, 37(12): 3048-3060. Wang Jianing, Zou Qiang, Hu Jiawen, et al.An optimal design method for medium-voltage insulated high-power medium-frequency transformer[J]. Transa-ctions of China Electrotechnical Society, 2022, 37(12): 3048-3060. [11] Zhao Shishuo, Li Qiang, Lee F C.High frequency transformer design for modular power conversion from medium voltage AC to 400V DC[C]//2017 IEEE Applied Power Electronics Conference and Expo-sition (APEC), Tampa, FL, USA, 2017: 2894-2901. [12] Zhao Yikun, Zhang Guoqiang, Liao Zhenghai, et al.Optimal design of insulation structure of HV-HF transformer based on high-frequency insulation pro-perties of gas-solid system[C]//2020 IEEE Electrical Insulation Conference (EIC), Knoxville, TN, USA, 2020: 482-485. [13] 梁湘湘, 蔡明星, 任玉强, 等. 电力电子变压器中高频变压器损耗分析与设计[J]. 电力机车与城轨车辆, 2020, 43(3): 6-12. Liang Xiangxiang, Cai Mingxing, Ren Yuqiang, et al.Loss analysis and design of high-frequency trans-former in power electronic transformer[J]. Electric Locomotives & Mass Transit Vehicles, 2020, 43(3): 6-12. [14] 王佳宁, 邹强, 庄加才, 等. 大功率多绕组中频变压器的优化设计研究[J]. 电力电子技术, 2021, 55(8): 31-35. Wang Jianing, Zou Qiang, Zhuang Jiacai, et al.Research on optimization design for high-power-multi-winding mid-frequency transformer[J]. Power Electronics, 2021, 55(8): 31-35. [15] 张薷方. 基于有限元法的IGBT模块封装散热性能及热应力的仿真研究[D]. 重庆: 重庆大学, 2015. [16] 付可欣. 高压绝缘用环氧树脂交联网络结构设计与筛选[D]. 北京: 华北电力大学, 2020. [17] 陈海涛, 张晶, 丛大龙, 等. 电火花沉积钨涂层的温度场和残余应力有限元模拟[J]. 表面技术, 2022, 51(1): 140-149. Chen Haitao, Zhang Jing, Cong Dalong, et al.Finite element simulation of the temperature field and residual stress of tungsten coating deposited by electro-spark deposition[J]. Surface Technology, 2022, 51(1): 140-149. [18] 曹小鹏, 陈武, 宁光富, 等. 基于多目标遗传算法的大功率高频变压器优化设计[J]. 中国电机工程学报, 2018, 38(5): 1348-1355. Cao Xiaopeng, Chen Wu, Ning Guangfu, et al.Optimization design of high-power high-frequency transformer based on multi-objective genetic algo-rithm[J]. Proceedings of the CSEE, 2018, 38(5): 1348-1355. [19] 张晓星, 陈霄宇, 肖淞, 等. 改性SiO2增强环氧树脂热力学性能的分子动力学模拟[J]. 高电压技术, 2018, 44(3): 740-749. Zhang Xiaoxing, Chen Xiaoyu, Xiao Song, et al.Molecular dynamics simulation of thermal-mechanical properties of modified SiO2 reinforced epoxy resin[J]. High Voltage Engineering, 2018, 44(3): 740-749. [20] 沈小军, 孟令轩, 付绍云. 石墨烯-多壁碳纳米管协同增强环氧树脂复合材料的低温力学性能[J]. 复合材料学报, 2015, 32(1): 21-26. Shen Xiaojun, Meng Lingxuan, Fu Shaoyun.Cryogenic mechanical properties of epoxy composites synergistically reinforced by graphene-multi-walled carbon nanotubes[J]. Acta Materiae Compositae Sinica, 2015, 32(1): 21-26. [21] 张国仲, 李晶, 振玉民, 等. 干式变压器气候和环境试验[J]. 变压器, 2005, 42(7): 1-3. Zhang Guozhong, Li Jing, Zhen Yumin, et al.Climatic and environmental test for dry-type trans-former[J]. Transformer, 2005, 42(7): 1-3. [22] 王文俊, 王维玮, 洪旭辉. 纳米纤维素晶须的表面改性及其在环氧树脂中的应用[J]. 高分子学报, 2015(9): 1036-1043. Wang Wenjun, Wang Weiwei, Hong Xuhui.Surface modification of cellulose nanowhiskers and appli-cation in epoxy resin[J]. Acta Polymerica Sinica, 2015(9): 1036-1043. [23] Wang Kun, Yang Wei, Chen Yun, et al.The epoxy packaging materials modified by flexible mono-hydroxy polyether chain for high frequency power transformer[C]//IEEE 3rd International Con-ference on Automation, Electronics and Electrical Engin-eering (AUTEEE), Shenyang, China, 2021: 239-242. [24] Zhang Song.Surface NH2-functionalized by C doping of boron nitride nanotube to improve the thermal conductivity of epoxy composites[J]. Composites Part B: Engineering, 2021, 223: 109106. [25] 潘晓辉, 陈强. MATLAB 5.1全攻略宝典[M]. 北京: 中国水利水电出版社, 2000.