电工技术学报  2018, Vol. 33 Issue (17): 4069-4077    DOI: 10.19595/j.cnki.1000-6753.tces.171145
电机与电器 |
基于有取向硅钢的 轴向磁通开关磁阻电机准三维解析分析与设计
马霁旻1, 王杜1, 曲荣海2, 李健2, 李新华1
1. 湖北工业大学电气与电子工程学院 武汉 430068;
2. 强电磁工程与新技术国家重点实验室(华中科技大学) 武汉 430074
Quasi-Three-Dimensional Analysis and Design of an Axial Flux Switched Reluctance Motor Based on Grain Oriented Silicon Steel
Ma Jimin1, Wang Du1, Qu Ronghai2, Li Jian2, Li Xinhua1
1. School of Electrical & Electronic Engineering Hubei University of Technology Wuhan 430068 China;
2. State Key Laboratory of Advanced Electromagnetic Engineering and Technology Huazhong University of Science and Technology Wuhan 430074 China
全文: PDF (17569 KB)  
输出: BibTeX | EndNote (RIS)      
摘要 轴向磁通开关磁阻电机定、转子齿形在不同圆周半径上极弧角度变化不一致,利用二维解析法分析该类电机会带来较大误差。该文利用准三维解析法对轴向磁通电机展开径向分层计算,确定电机转子关键位置处的磁链特性。在准三维解析法分析的基础上,利用准三维有限元方法对基于不同铁磁材料的模型进行了比较分析。研究结果和样机测试数据表明:基于有取向硅钢材料的轴向磁通开关磁阻电机定、转子磁极轴线对齐位置处的磁链值可以提高15%,准三维解析法的分层计算精度较高,对于电机初期设计而言,该方法的磁链分析误差从工程上认为是可以接受的。
服务
把本文推荐给朋友
加入我的书架
加入引用管理器
E-mail Alert
RSS
作者相关文章
马霁旻
王杜
曲荣海
李健
李新华
关键词 轴向磁通开关磁阻电机极弧角度准三维解析法有取向硅钢材料电磁性能    
Abstract:According to the different change ratio between the pole arc of the stator tooth and that of rotor tooth at the different circumferential in the axial flux switched reluctance motor (AFSRM), the quasi- three-dimensional (Q-3-D) analytical method is used to study the AFSRM in the different radial delamination, and the accuracy of the Q-3-D analysis is improved to determine the initial electromagnetic design scheme compared with the result of the two dimensional analysis method. On the basis of Q-3-D analytical method, Q-3-D finite element method is employed to optimize the main design parameters with the different electrical steel material. Research results and prototype test data show that, the electromagnetic performance of the AFSRM with the grain oriented electrical steel is superior to the traditional non oriented material motor. Q-3-D analysis method has a high accuracy, for the initial design of the motor, the analysis error is considered acceptable.
Key wordsAxial flux switched reluctance motor    pole arc    quasi-three-dimensional analytical method    grain oriented electrical steel    electromagnetic performance   
收稿日期: 2017-08-14      出版日期: 2018-09-14
PACS: TM352  
基金资助:国家自然科学基金(51407082,51337004)、湖北工业大学博士科研启动基金(BSQD2017011)和太阳能高效利用及储能运行控制湖北省重点实验室开放研究基金(HBSEES201711)资助项目
通讯作者: 马霁旻 男,1980年生,博士,硕士生导师,研究方向为磁阻电机以及新型永磁电机设计和驱动控制。E-mail:yuwen026@sina.com   
作者简介: 王杜 男,1993年生,硕士研究生,研究方向为磁阻电机以及新型永磁电机的本体设计。E-mail:1187223665@qq.com
引用本文:   
马霁旻, 王杜, 曲荣海, 李健, 李新华. 基于有取向硅钢的 轴向磁通开关磁阻电机准三维解析分析与设计[J]. 电工技术学报, 2018, 33(17): 4069-4077. Ma Jimin, Wang Du, Qu Ronghai, Li Jian, Li Xinhua. Quasi-Three-Dimensional Analysis and Design of an Axial Flux Switched Reluctance Motor Based on Grain Oriented Silicon Steel. Transactions of China Electrotechnical Society, 2018, 33(17): 4069-4077.
链接本文:  
https://dgjsxb.ces-transaction.com/CN/10.19595/j.cnki.1000-6753.tces.171145          https://dgjsxb.ces-transaction.com/CN/Y2018/V33/I17/4069