Review on Development and Design of High Speed Machines
Zhang Fengge1, Du Guanghui1, Wang Tianyu2, Liu Guangwei1
1.School of Electrical Engineering Shenyang University of Technology Shenyang 110870 China 2.School of Mechanical Engineering Shenyang Institute of Engineering Shenyang 110136 China
Abstract：This paper analyzes the development state of high speed motors, and sums up the limit affordable values of different high speed machines.The structures and design feathers of high speed machines are analyzed in detail, including stator design, different rotor structure designs, rotor dynamics analysis, bearings selection, as well as cooling system design.At last, the problems faced by high speed machines development are summarized and development trends are prospected.
张凤阁, 杜光辉, 王天煜, 刘光伟. 高速电机发展与设计综述[J]. 电工技术学报, 2016, 31(7): 1-18.
Zhang Fengge, Du Guanghui, Wang Tianyu, Liu Guangwei. Review on Development and Design of High Speed Machines. Transactions of China Electrotechnical Society, 2016, 31(7): 1-18.
[1] 王凤翔.高速电机的设计特点及相关技术研究[J].沈阳工业大学学报,2006,28(3):258-263. Wang Fengxiang.Study on design feature and related technology of high speed electrical machines[J].Journal of Shenyang University of Technology,2006,28(3):258-263. [2] Gieras J F.Design of permanent magnet brushless motors for high speed applications[C]//17th International Conference on Electrical Machines and Systems (ICEMS),Hangzhou,2014:1-16. [3] Moghaddam R R.High speed operation of electrical machines,a review on technology,benefits and challenges[C]//IEEE Energy Conversion Congress and Exposition (ECCE),Pittsburgh,PA,2014:5539-5546. [4] Bianchi N,Bolognani S,Luise F.Potentials and limits of high-speed PM motors[J].IEEE Transactions on Industry Applications,2004,40(6):1570-1578. [5] 董剑宁,黄允凯,金龙,等.高速永磁电机设计与分析技术综述[J].中国电机工程学报,2014,34(27):4640-4653. Dong Jianning,Huang Yunkai,Jin Long,et al.Review on high speed permanent magnet machines including design and analysis technologies[J].Proceedings of the CSEE,2014,34(27):4640-4653. [6] Tenconi A,Vaschetto S,Vigliani A.Electrical machines for high-speed applications:design considerations and tradeoffs[J].IEEE Transactions on Industrial Electronics,2014,61(6):3022-3029. [7] Boglietti A,Cavagnino A,Tenconi A,et al.Key design aspects of electrical machines for high-speed spindle applications[C]//36th Annual Conference of the IEEE Industrial Electronics Society,Glendale,AZ,2010:1735-1740. [8] Kolondzovski Z,Arkkio A,Larjola J,et al.Power limits of high-speed permanent-magnet electrical machines for compressor applications[J].IEEE Transactions on Energy Conversion,2011,26(1):73-82. [9] 沈建新,李鹏,郝鹤,等.高速永磁无刷电机电磁损耗的研究概况[J].中国电机工程学报,2012,33(3):62-74. Shen Jianxin,Li Peng,Hao He,et al.Study on electromagnetic losses in high-speed permanent magnet brushless machines-the state of the art[J].Proceedings of the CSEE,2012,33(3):62-74. [10]Borisavljevic A,Polinder H,Ferreira J A.On the speed limits of permanent-magnet machines[J].IEEE Transactions on Industrial Electronics,2010,57(1):220-227. [11]江善林.高速永磁同步电机的损耗分析与温度场计算[D].哈尔滨:哈尔滨工业大学,2010. [12]Dong Jianning,Huang Yunkai,Jin Long,et al.Thermal optimization of a high-speed permanent magnet motor[J].IEEE Transactions on Magnetics,2014,50(2):749-752. [13]Danilevich J B,Kruchinina I Y,Antipov V N,et al.Some problems of the high-speed permanent magnet miniturbogenerators development[C]//18th International Conference on Electrical Machines,Vilamoura,2008:1-4. [14]Ede J D,Zhu Z Q,Howe D.Rotor resonances of high-speed permanent magnet brushless machines[J].IEEE Transactions on Industry Applications,2002,38(6):1542-1548. [15]Gerada D,Mebarki A,Brown N L,et al.Design aspects of high-speed high-power-density laminated-rotor induction machines[J].IEEE Transactions on Industrial Electronics,2011,58(9):4039-4047. [16]Cho H W,Ko K J,Choi J Y,et al.Rotor natural frequency in high-speed permanent-magnet synchronous motor for turbo-compressor application[J].IEEE Transactions on Magnetic,2011,47(10):4258-4261. [17]Gerada D,Mebarki A,Brown N L,et al.High-speed electrical machines:technologies,trends,and developments[J].IEEE Transactions on Industrial Electronics,2014,61(6):2946-2959. [18]Ahrens M,Bikle U,Gottkehaskamp R,et al.Electrical design of high-speed induction motors of up to 15 MW and 20 000 RPM[C]//International Conference on Power Electronics,Machines and Drives,Bath,United Kingdom,2002:381-386. [19]Pyrhonen J,Nerg J,Kurronen P,et al.High-speed,high output,solid-rotor induction motor technology for gas compression[J].IEEE Transactions on Industrial Electronics,2010,57(1):272-280. [20]Gieras J F,Saari J.Performance calculation for a high-speed solid-rotor induction motor[J].IEEE Transactions on Industrial Electronics,2012,59(6):2689-2700. [21]James O,Samotyj M,Ferrier R.Applications of high speed horsepower ASD controlled induction motors to gas pipeline[C]//Fifth European Conference on Power Electronics and Applications,Brighton,1993,5:430-435. [22]Saari J,Arkkio A.Losses in high speed asynchronous motors[C]//Proceedings of ICEM,1994,3:704-708. [23]Rahman M A,Chiba A,Fukao T.Super high speed electrical machines-summary[C]//IEEE Power Engineering Society General Meeting,Denver,CO,2004,2:272-1275. [24]Caprio M,Lelos V,Herbst J,et al.Advanced induction motor endring design features for high speed applications[C]//IEEE International Conference on Electric Machines and Drives,San Antonio,TX,2005,1:993-998. [25]Wood B M,Olsen C L,Hartzo G D,et al.Development of an 11 000 r/min 3 500 HP induction motor and adjustable speed drive for refinery service[J].IEEE Transactions on Industry Applications,1997,33(3):815-825. [26]Lahteenmaki J.Design and voltage supply of high-speed induction machines[D].Espoo,Finland,Helsinki University of Technology,2002. [27]重庆德马电机有限公司.上海鼓风机厂大功率压缩机高速电机[EB/OL].http://www.dmbp.com/news.asp?id=1777,2014-8-8. [28]Papini L,Gerada C,Gerada D,et al.High speed solid rotor induction machine:analysis and performances[C]//17th International Conference on Electrical Machines and Systems,Hangzhou,2014:2759-2765. [29]Bumby J R,Spooner E,Jagiela M.Equivalent circuit analysis of solid-rotor induction machines with reference to turbocharger accelerator applications[J]//IEE Proceedings:Electric Power Applications,2006,153(1):31-39. [30]Viggiano F,Schweitzer G.Active magnetic support and design of high speed rotors for powerful electric drives[C]//International Symposium on Magnetic Bearings,1992,1:549-558. [31]Gerada D,Mebarki A,Brown N L,et al.Design,modelling and testing of a high speed induction machine drive[C]//IEEE Energy Conversion Congress and Exposition,Raleigh,NC,2012:4649-4655. [32]Popa D C,Fodorean D.Design and performances evaluation of a high speed induction motor used for the propulsion of an electric vehicle[C]//2014 International Symposium on Power Electronics,Electrical Drives,Automation and Motion (SPEEDAM),Ischia,2014:88-93. [33]重庆德马电机有限公司.重庆通用公司制冷压缩机高速电机[EB/OL].http://www.dmbp.com/news. asp?id=1772,2014-8-8. [34]Siegwart R,Larsonneur R,Traxler A.Design and performance of high speed milling spindle in digitally controlled AMB’s[C]//International Symposium on Magnetic Bearings,1990,1:197-204. [35]Soong W L,Kliman G B,Johnson R N,et al.Novel high-speed induction motor for a commercial centrifugal compressor[J].IEEE Transactions on Industry Applications,2000,36(3):706-713. [36]Mekhiche M,Kirtley J L,Tolikas M,et al.High speed motor drive development for industrial applications[C]//International Conference IEMD ′99 Electric Machines and Drives,Seattle,WA,1999,1:244-248. [37]李玉超.280kW高速感应电动机的设计与分析[D].沈阳:沈阳工业大学,2015. [38]Huppunen J.High-speed solid-rotor induction machine-electromagnetic calculation and design[D].Finland,Lappeenranta:Lappeenranta University of Technology, 2004. [39]Kim Y K,Choi M C,Suh K H,et al.High-speed induction motor development for small centrifugal compressor[C]//5th International Conference on Electrical Machines and Systems,Shenyang,2001,2:891-894. [40]Ikeda M,Sakabe S,Higashi K.Experimental study of high speed induction motor varying rotor core construction[J].IEEE Transactions on Energy Conversion,1990,5(1):98-103. [41]Aho T.Electromagnetic design of a solid steel rotor motor for demanding operation environments[D].Finland,Lappeenranta:Lappeenranta University of Technology, 2007. [42]Hong D K,Choi J H,Han P W,et al.Analysis of high speed induction motor for spindle made by copper die casting process[J].Internationl Journal of Precision Engineering and Manufacturing,2012,13(12):2251-2257. [43]Centner M,Hanitsch R,Schafer U.Comparison of high-speed induction motors employing cobalt-iron and silicon electrical steel[C]//18th International Conference on Electrical Machines,Vilamoura,2008:1-6. [44]江虹.高速感应电动机电磁设计方法的研究[D].哈尔滨:哈尔滨工业大学,2006. [45]Larsson M,Johansson M,Naslund L,et al.Design and evalution of high-speed induction machine[C]//IEEE International Electric Machines and Drives Conference,2003,1:77-82. [46]Klma J,Vitek O.Analysis of high-speed induction motor[C]//Proceedings of the 16th International Conference on Mechatronics-Mechatronika,Brno,2014:85-91. [47]Anbarasu R,Gupta R K,Sharma N D,et al.Design and experimental investigation of high speed squirrel cage induction motor[C]//Proceedings of the 1996 International Conference on Power Electronics,Drives and Energy Systems for Industrial Growth (PEDES),New Delhi,1996,2:920-926. [48]Bailey C,Saban D M,Guedes Pinto P.Design of high-speed direct-connected permanent-magnet motors and generators for the petrochemical industry[J].IEEE Transactions on Industry Applications,2009,45(3):1159-1165. [49]Gonzalez D A,Saban D M.Study of the copper losses in a high-speed permanent-magnet machine with form-wound windings[J].IEEE Transactions on Industrial Electronics,2014,61(6):3038-3045. [50]Huynh C,Hawkins L,Farahani A,et al.Design and development of a two-megawatt,high speed permanent magnet alternator for shipboard application[J].Naval Engineers Journal,2005,17(4):23-29. [51]Shelley T.Direct coupled turbines power the future[J].Eureka,1995,15(9):35-36. [52]Paulides J J H,Jewell G W,Howe D.An evaluation of alternative stator lamination materials for a high-speed,1.5 MW permanent-magnet generator[J].IEEE Transactions on Magnetics,2004,40(4):2041-2043. [53]Huynh C,Zheng L P,Acharya D.Losses in high speed permanent magnet machines used in microturbine applications[J].Journal of Engineering for Gas Turbines and Power,2009,131(2):1-6. [54]Aglen O,Andersson A.Thermal analysis of a high-speed generator[C]//38th IAS Annual Meeting: Conference Record of the Industry Applications Conference,Salt Lake,United States,2003,1:547-554. [55]邱洪波.高速永磁发电机转子涡流损耗优化及对温度分布影响的研究[D].哈尔滨:哈尔滨理工大学,2014. [56]张凤阁,杜光辉,王天煜,等.1.12 MW 高速永磁电机不同冷却方案的温度场分析[J].电工技术学报,2014,29(S):66-72. Zhang Fengge,Du Guanghui,Wang Tianyu,et al.Temperature field analysis of 1.12 MW high speed permanent magnet machine with different cooling schemes[J].Transactions of China Electrotechnical Society,2014,29(S):66-72. [57]Wang K,Jin M J,Shen J X,et al.Study on rotor structure with different magnet assembly in high-speed sensorless brushless DC motors[J].IET Electric Power Applications,2010,4(4):241-248. [58]Shigematsu K,Oyama J,Higuchi T,et al.The study of eddy current in rotor and circuit coupling analysis for small size and ulta high speed motor[C]//The 4th International Power Electronics and Motion Control Conference,Xi’an,2004,1:275-279. [59]Zhang Xiaochen,Li Weili,Kou Baoquan,et al.Electrothermal combined optimization on notch in air-cooled high-speed permanent-magnet generator[J].IEEE Transactions on Magnetics,2015,51(1):1-10. [60]邢军强.高速永磁电机转子涡流损耗及通风散热研究[D].沈阳:沈阳工业大学,2011. [61]Zwyssig C,Duerr M,Hassler D,et al.An ultra-high speed,500 000 r/min,1 kW electrical drive system[C]//Power Conversion Conference,Nagoya,2007:1577-1583. [62]Cho H,Jang S.The influence of operating mode on rotor losses in high speed permanent magnet synchronous motor/generator for micro-gas turbine[C]//IEEE International Magnetics Conference,San Diego,CA,2006:983-986. [63]Hong D K,Woo B C,Koo D H.Rotordynamics of 120 000 r/min 15 kW ultra high speed motor[J].IEEE Transactions on Magnetic,2009,45(6):2831-2834. [64]田野,孙岩桦,杨利花,等.带弹性支撑和挤压油膜阻尼器的高速电机支撑系统实验研究[J].中国电机工程学报,2012,32 (27):79-86. Tian Ye,Sun Yanhua,Yang Lihua,et al.Experimental studies on support systems of high speed motors with flexible squirrel-cage support and squeeze film dampers[J].Proceedings of the CSEE,2012,32(27):79-86. [65]Xu Longya,Wang Changjiang.Implementation and experimental investigation of sensorless control schemes for PMSM in super-high variable speed operation[C]//Proceedings of the 33rd IAS Annual Meeting,St.Louis,MO,USA,1998,1:483-489. [66]鲍海静.飞轮储能用高速永磁同步电机设计及关键技术研究[D].哈尔滨:哈尔滨工业大学,2014. [67]高义冬.飞轮储能用高速永磁同步电机的设计与分析[D].镇江:江苏科技大学,2014. [68]Takahashi I,Koganezawa T,Su G,et al.A super high speed PM motor drive system by a quasi-current source inverter[J].IEEE Transactions on Industry Applications,1994,30(3):683-690. [69]Riemer B,Lessmann M,Hameyer K.Rotor design of a high-speed permanent magnet synchronous machine rating 100 000 rpm at 10 kW[C]//IEEE Energy Conversion Congress and Exposition (ECCE),Atlanta,GA,2010:3978-3985. [70]Noguchi T,Takata Y,Yamashita Y,et al.220 000 r/min 2 kW PM motor drive for turbocharger[J].Electrical Engineering in Japan,2007,161(3):31-40. [71]Borisavljevic A,Polinder H,Ferreira J A.Enclosure design for a high-speed permanent magnet rotor[C]//5th IET Conference on Power Electronics,Machines and Drives,Brighton,UK,2010:1-6. [72]Smith D J B,Mecrow B C,Atkinson G J,et al.Shear stress concentrations in permanent magnet rotor sleeves[C]//International Conference on Electrical Machines (ICEM),Rome,2010:1-6. [73]Dong Jianning,Huang Yunkai,Jin Long,et al.Development of an air-cooled 150kW high speed permanent magnet motor with gramme ring windings for turbo blowers[C]//17th International Conference on Electrical Machines and Systems,Hangzhou,2014:3534-3538. [74]田拥胜,孙岩桦,虞烈.高速永磁电机电磁轴承转子系统的动力学及实验研究[J].中国电机工程学报,2012,32(9):116-123. Tian Yongsheng,Sun Yanhua,Yu Lie.Dynamical and experimental researches of active magnetic bearing rotor systems for high-speed pm machines[J].Proceedings of the CSEE,2012,32(9):116-123. [75]Pfitser P D,Perriard Y.Very high speed slotless PM motors:analytical modelling,optimization,design and torque measurement methods[J].IEEE Transactions on Industrial Electronics,2010,57(1):296-303. [76]Hong D K,Joo D,Woo B C,et al.Performance verification of a high speed motor-generator for a microturbine generator[J].Internationl Journal of Precision Engineering and Manufacturing,2013,14(7):1237-1244. [77]Hu Y,Wu T,Chow L,et al.Design of a 3 kW 150k RPM super high-speed permanent magnet synchronous motor[C]//International Conference on Electrical Machines,Berlin,2014:2543-2548. [78]Binder A,Schneider T,Klohr M.Fixation of buried and surface-mounted magnets in high-speed permanent-magnet synchronous machines[J].IEEE Transactions on Industry Applications,2006,42(4):1031-1037. [79]Luise F,Tessarolo A,Agnolet F,et al.A high-performance 640 kW 10 000 r/min halbach-array PM slotless motor with active magnetic bearings,part II:manufacturing and testing[C]//International Symposium on Power Electronics,Electrical Drives,Automation and Motion,Ischia,2014:1245-1250. [80]Luise F,Tessarolo A,Agnolet F,et al.A high-performance 640 kW 10 000 r/min halbach-array PM slotless motor with active magnetic bearings,part I:preliminary and detailed design[C]//International Symposium on Power Electronics,Electrical Drives,Automation and Motion,Ischia,2014:1237-1244. [81]南车电机公司成功研制高速永磁变频电机系统[EB/OL].新华网.http://www.hn.xinhuanet.com/2015-04/29/c_1115134170.htm,2015-4-29. [82]沈建新,郝鹤,袁承.高速永磁无刷电机转子护套周向开槽的有限元分析[J].中国电机工程学报,2012,32(36):53-60. Shen Jianxin,Hao He,Yuan Cheng.FEA study on circumferential grooves on rotor retaining sleeve of high-speed PM brushless motors[J].Proceedings of the CSEE,2012,32(36):53-60. [83]郝鹤.高速永磁无刷电机多场综合分析及无位置传感器控制[D].杭州:浙江大学,2014. [84]Fernando W U N,Gerada C.High speed permanent magnet machine design with minimized stack-length under electromagnetic and mechanical constraints[J].International Journal of Applied Electromagnetics and Mechanics,2014,46(1):95-109. [85]El-Hasan T.Rotor eddy current determination using finite element analysis for high-speed permanent magnet machines[C]//IEEE 23rd International Symposium on Industrial Electronics,Istanbul,2014:885-889. [86]陈亮亮,祝长生,王萌.碳纤维护套高速永磁电机热态转子强度[J].浙江大学学报(工学版),2015,49(1):162-172. Chen Liangliang,Zhu Changsheng,Wang Meng.Strength analysis for thermal carbon-fiber retaining rotor in high-speed permanent magnet machine[J].Journal of Zhejiang University:Engineering Science,2015,49(1):162-172. [87]Lin S,Wu T X,Zhou L,et al.Modeling and design of super high speed permanent magnet synchronous motor (PMSM)[C]//IEEE National Aerospace and Electronics Conference,Dayton,OH,2008:41-44. [88]沈建新,陈利根.永磁无刷电机中平行充磁2极气隙磁场的解析计算[J].电机与控制应用,2006,33(1):7-10. Shen Jianxin,Chen Ligen.Analytical calculation of air gap field in 2-pole permanent magnet brushless motor with parallel-magnetisation[J].Machines and Control Application,2006,33(1):7-10. [89]Honda Y,Yokote S,Higaki T,et al.Using the halbach magnet array to develop an ultrahigh-speed spindle motor for machine tools[C]//Conference Record of the 1997 IEEE Industry Applications Conference, New Orleans,LA,1997,1:56-60. [90]Zwyssig C,Kolar J W,Thaler W.Design of a 100 W,500 000 rpm permanent-magnet generator for mesoscale as turbines[C]//Conference Record of the 2005 Industry Applications Conference,2005,1:253-260. [91]陈小军.高速永磁无刷直流电机磁热耦合分析与效率优化研究[D].广州:广东工业大学,2013. [92]Nagorny A S,Dravid N V,Jansen R H,et al.Design aspects of a high speed permanent magnet synchronous motor/generator for flywheel applications[C]//IEEE International Conference on Electric Machines and Drives,San Antonio,TX,2005:635-641. [93]次元平.高速电主轴永磁电机结构的研究[D].沈阳:沈阳工业大学,2015. [94]Hsu J S,Burress A,Lee S T,et al.16 000 rpm Interior permanent magnet reluctance machine with brushless field excitation[C]//IEEE Industry Application Society Annual Meeting,Edmonton,Alta,2008:l-6. [95]Kim S I,Kim Y K,Lee G H,et al.A novel rotor configuration and experimental verification of interior PM synchronous motor for high-speed applications[J].IEEE Transactions on Magnetics,2012,48(2):843-846. [96]Luca P,Tsarafidy R,David G,et al.A high-speed permanent-magnet machine for fault-tolerant drivetrains[J].IEEE Transactions on Industrial Electronics,2014,61(6):3071-3080. [97]Jang S M,Cho H W,Lee S H,et al.Analysis of cogging torque for high speed motor/generator[C]//Sixth International Conference on Electrical Machines and Systems,Beijing,China,2003,1:205-207. [98]薛劭申.高速永磁无刷电机设计与控制系统研究[D].北京:北京交通大学,2011. [99]Boubaker N,Matt D,Enrici P,et al.Study of banding techniques with a view to reduce the rotor eddy-current loss in a high-speed actuator dedicated to an aeronautical application[C]//International Conference on Electrical Machines,Berlin,2014:2583-2587. [100]Hwang C C,Hung S S,Liu C T,et al.Optimal design of a high speed SPM motor for machine tool applications[J].IEEE Transactions on Magnetics,2014,50(1):2276092. [101]Xu Jianchun,Liu Chuang.Research on high-speed permanent magnet generator for a miniature turbojet[C]//Proceedings of 6th IEEE Conference on Industrial Electronics and Applications,Beijing,2011:2783-2786. [102]Schneider T,Petersen J,Binder A.Influence of pole pair combinations on high-speed bearingless permanent magnet motor performance[C]//4th IET Conference on Power Electronics,Machines and Drives,York,2008:707-711. [103]Upadhyay P,Mohan N.Design and FE analysis of surface mounted permanent magnet motor/generator for high-speed modular flywheel energy storage systems[C]//IEEE Energy Conversion Congress and Exposition,San Jose,CA,2009:3630-3633. [104]Cho H W,Jang S M,Choi S K.A design approach to reduce rotor losses in high-speed permanent magnet machine for turbo-compressor[J].IEEE Transactions on Magnetics,2006,42(10):3521-3523. [105]Zhu Z Q,Ng K,Howe D.Design and analysis of high-speed brushless permanent magnet motors[C]//Eighth International Conference on Electrical Machines and Drives,Cambridge,UK,1997:381-385. [106]余莉,胡虔生,崔杨,等.高速永磁无刷直流电动机铁耗的分析计算及实验[J].微特电机,2008(3):11-13. Yu Li,Hu Qiansheng,Cui Yang,et al.Analysis and calculation of the iron losses of high speed permanet motor[J].Micro Motor,2008(3):11-13. [107]Richter E,Ferreira C.Performance evaluation of a 250 kW switched reluctance starter generator[C]//Conference Record of the 1995 IEEE Industry Applications Conference,Orlando,FL,1997,1:434-440. [108]Ferreira C A,Jones S R,Heglund W S,et al.Detailed design of a 30 kW switched reluctance S/G system for a gas turbine application[J]//IEEE Transactions on Industry Applications,1995,31(3):553-561. [109]Bartolo J B,Geradal C.The electromagnetic design of a high speed 45 kW switched reluctance machine having a novel rotor geometry for aerospace application[C]//International Conference on Electrical Machines and Systems (ICEMS),Berlin,2014:2513-2519. [110]Ikaheimo J,Kolehmainen J,Kansakangas T,et al.Synchronous high-speed reluctance machine with novel rotor construction[J].IEEE Transactions on Industrial Electronics,2014,61(6):2969-2975. [111]Morel L,Fayard H,Fos R V,et al.Study of ultra high speed switched reluctance motor drive[C]//Conference Record of the 2000 IEEE Industry Applications Conference,Rome,2000,1:87-92. [112]周强,刘闯,朱学忠,等.超高速开关磁阻电动机设计[J].中国电机工程学报,2009,29(9):87-92. Zhou Qiang,Liu Chuang,Zhu Xuezhong,et al.Design of super high speed switched reluctance motor[J].Proceedings of the CSEE,2009,29(9):87-92. [113]裴丽娜.超高速开关磁阻电机电磁分析与设计[D].北京:北京交通大学,2010. [114]金坚.6/4结构高速开关磁阻电机的研究[D].南京:南京航空航天大学,2009. [115]周强.高速开关磁阻电机的关键技术研究与实践[D].南京:南京航空航天大学,2008. [116]Brauer H J,De Doncker R W.Thermal modeling of a high speed SRM for vacuum cleaners[J].European Power Electronics and Drives Journal,2012,22(2):22-29. [117]范冬,杨艳,邓智泉,等.无轴承高速开关磁阻电机设计中的关键问题[J].电机与控制学报,2006,10(6):547-552. Fan Dong,Yang Yan,Deng Zhiquan,et al.The key technology on designing a high-speed bearingless switched reluctance motor[J].Electric Machines and Control,2006,10(6):547-552. [118]孙健.6/2结构高速开关磁阻电机的研究与实现[D].南京,南京航空航天大学,2007. [119]Kim J,Krishnan R.High efficiency single-pulse controlled switched reluctance motor drive for high speed (48 krpm) application:analysis,design,and experimental verification[C]//IEEE Industry Applications Society Annual Meeting,Edmonton,Alta,2008,1:1-8. [120]Kunz J,Cheng S,Duan Y,et al.Design of a 750 000 r/min switched reluctance motor for micro machining[C]//IEEE Energy Conversion Congress and Exposition (ECCE),Atlanta,GA,2010:3986-3992. [121]Lee D H,Pham T H,Ahn J W.Design and operation characteristics of four-two pole high speed SRM for torque ripple reduction[J].IEEE Transactions on Industrial,2013,60(9):3637-3643. [122]朱宏基.电动工具用高速开关磁阻电机的设计与实现[D].株洲:湖南工业大学,2014. [123]张珍.小功率高速开关磁阻电机驱动系统的设计与应用[D].武汉:华中科技大学,2012. [124]Howe D,Mason P,Mellor P H,et al.Flywheel peak power buffer for electric hybrid vehicles[C]//International Conference IEMD ′99 Electric Machines and Drives,Seattle,WA,1999:508-510. [125]李杏.飞轮储能用外转子高速永磁同步电机研究[D].哈尔滨:哈尔滨工业大学,2013. [126]Kohari Z.Test results of a compact superconducting flywheel energy storage with disk-type,permanent magnet motor/generator unit[J].IEEE Transactions on Application Superconductivity,2009,3(19):2095-2098. [127]Nguyen T D,Tseng K J,Zhang S,et al.A flywheel cell for energy storage system[C]//IEEE International Conference on Sustainable Energy Technologies,Singapore,2008:214-219. [128]Seok M J,Dae J Y,Kyoung J K,et al.Design and experimental evaluation of synchronous machine without iron loss using double-sided halbach magnetized PM rotor in high power FESS[J].IEEE Transactions on Magnetics,2008,44(11):4337-4340. [129]刘光伟,赵新刚,张凤阁,等.高速永磁爪极电机铁耗与空气摩擦损耗计算[J].电工技术学报,2015,30(2):148-154. Liu Guangwei,Zhao Xingang,Zhang Fengge,et al.Iron loss and air friction loss for high speed permanent magnet claw pole machines[J].Transactions of China Electrotechnical Society,2015,30(2):148-154. [130]徐衍亮,赵建辉,房建成.高速储能飞轮用无铁心永磁无刷直流电动机的分析与设计[J].电工技术学报,2004,19(12):24-28. Xu Yanliang,Zhao Jianhui,Fang Jiancheng.Analysis and design of coreless permanent magnet brushless DC machine in high-speed energy storage flywheel application[J].Transactions of China Electrotechnical Society,2004,19(12):24-28. [131]黄允凯,胡虔生,朱建国.顾及旋转铁耗的高速爪极电机三维磁热耦合分析[J].电工技术学报,2010,25(5):54-60. Huang Yunkai,Hu Qiansheng,Zhu Jianguo.Magneto-thermal analysis of a high-speed claw pole motor considering rotational core loss[J].Transactions of China Electrotechnical Society,2010,25(5):54-60. [132]Ignat M,Haraguta I C.The asyncronous high speed motor for an axial compressor application[C]//International Aegean Conference on Electrical Machines and Power Electronics and 2011 Electromotion Joint Conference ,Istanbul,2013:211-215. [133]Zhang C,Tseng K J,Nguyen T D,et al.Design and loss analysis of a high speed flywheel energy storage system based on axial-flux flywheel-rotor electric machines[C]//9th International Power and Energy Conference,Singapore,2010:886-891. [134]Fodorean D,Popa D C,Minciunescu P,et al.Study of a high-speed motorization for electric vehicle based on PMSM,IM and VRSM[C]//International Conference on Electrical Machines (ICEM),Berlin,2014:2577-2582. [135]Bartolo J B,Zhang H,Gerada D,et al.High speed electrical generators,application,materials and design[C]//IEEE Workshop on Electrical Machines Design Control and Diagnosis,Paris,2013:47-59. [136]Lateb R,Enon J,Durantay L.High speed,high power electrical induction motor technologies for integrated compressors[C]//International Conference on Electrical Machines and Systems,Tokyo,2009:1-5. [137]Zhou Hao,Wang Fengxiang.Comparative study on high speed induction machine with different rotor structures[C]//International Conference on Electrical Machines and Systems,Seoul,2007:1009-1012. [138]周凤争.高速永磁无刷直流电机转子涡流损耗的研究[D].杭州:浙江大学,2008. [139]Yon J M,Mellor P H,Wrobel R,et al.Analysis of semipermeable containment sleeve technology for high-speed permanent magnet machines[J].IEEE Transactions on Energy Conversion,2012,27(3):646-653. [140]张凤阁,杜光辉,王天煜,等.基于多物理场的高速永磁电机转子护套研究[J].电机与控制学报,2014,18(6):15-21. Zhang Fengge,Du Guanghui,Wang Tianyu,et al.Rotor containment sleeve study of high-speed PM machine based on multi-physics fields[J].Electric Machines and Control,2014,18(6):15-21. [141]Zhang Fengge,Du Guanghui,Wang Tianyu,et al.Rotor retaining sleeve design of a 1.12 MW high-speed PM machine[J].IEEE Transactions on Industry Applications,2015,51(5):3675-2685. [142]张凤阁,杜光辉,王天煜,等.高速永磁电机转子不同保护措施的强度分析[J].中国电机工程学报,2013,33(增):195-202. Zhang Fengge,Du Guanghui,Wang Tianyu,et al.Rotor strength analysis of high-speed permanent magnet under different protection measures[J].Proceedings of the CSEE,2013,33(S):195-202. [143]王天煜.高速永磁电机转子综合设计方法及动力学特性的研究[D].沈阳:沈阳工业大学,2010. [144]李艳明,郭宏,谢清明,等.充磁导致的超高速永磁同步电机不平衡磁拉力[J].北京航空航天大学学报,2013,39(6):771-775. Li Yanming,Guo Hong,Xie Qingming,et al.Unbalanced magnetic pull due to the magnetizing in super high speed permanent magnet synchronous machine[J].Journal of Beijing University of Aeronautics and Astronautics,2013,39(6):771-775. [145]张治平,钟瑞兴,谢蓉,等.空调器及其制冷机的电机的冷却结构[P].201110282627.7,2011-09-21. [146]Arkkio A,Jokinen T,Lantto E.Induction and permanent-magnet synchronous machines for high-speed applications[C]//8th International Conference on Electrical Machines and Systems,Nanjing,2005:871-876. [147]张凤阁,杜光辉,王天煜,等.1.12 MW高速永磁电机多物理场综合设计[J].电工技术学报,2015,30(12):171-180. Zhang Fengge,Du Guanghui,Wang Tianyu,et al.Integrated design of 1.12 MW high speed PM machine based on multi-physics fields[J].Transactions of China Electrotechnical Society,2015,30(12):171-180. [148]Zhang Fengge,Du Guanghui,Wang Tianyu,et al.Electromagnetic design and loss calculations of a 1.12 MW high-speed permanent-magnet motor for compressor applications[J].IEEE Transactions on Energy Conversion,2016,31(1):132-140.
2016, Vol. 31 
