基于调制波分解的Vienna整流器的调制方法

doi:10.19595/j.cnki.1000-6753.tces.221055

Abstract
Figure/Table
References
Related Citation (15)

Download: PDF (5760 KB) HTML (1 KB)
Export: BibTeX | EndNote (RIS)

Abstract As a three-phase power factor corrector, the Vienna rectifier has the advantages of high reliability and simple control. It is widely used and plays an important role in power unidirectional flow fields, such as communication power supply, electric vehicle, wind power, and aeronautical power supply. Carrier-based pulse width modulation (CB-PWM) and space vector modulation (SVM) are usually used to achieve unity power factor and neutral point voltage balance. However, these modulation methods have the problem of current zero-crossing point distortion, which is also one of the characteristics of Vienna rectifier topology. Different symbols of modulation voltage and current cause current distortion. Many modulation strategies have been proposed to solve the zero-crossing distortion. However, only some can perfectly applied to the full modulation range or the modulation strategy to overmodulate the modulation voltage. This paper presents a modulation method that can minimize the current zero-crossing distortion while maintaining the neutral point voltage balance on the DC side. Because the Vienna output level is limited by the current symbol, this paper uses the dual modulation wave decomposition method to deal with neutral point voltage balance and zero-crossing distortion.
Neutral point voltage balance is an important indicator of the stable operation of the Vienna rectifier. An unbalanced neutral point voltage can cause serious DC side offset, leading to over-voltage of power devices and causing danger. In order to balance the neutral point voltage, this paper calculates the average current to be extracted or injected during a carrier cycle by detecting the difference in capacitance voltage between the upper and lower DC sides obtained from the feedback. Combined with the expression of the duty cycle of each level, the zero-sequence voltage to be injected is calculated to balance the neutral point voltage.
In order to deal with the current zero crossing distortion, the modulation wave is divided into fixed modulation and free modulation waves. The fixed modulation wave is affected by the current symbol. In the current zero crossing area, a zero-sequence voltage is injected to clamp its zero-crossing phase voltage to 0. Injecting zero sequence voltage in high regulation will over-modulate, changing the relationship between line voltage and causing current distortion. The current zero crossing distortion cannot be wholly suppressed in high modulation. This paper uses a minimum synthetic error method in high modulation to minimize the change of line voltage. When the current zero crossing, the modulation voltage is obtained by calculation, instead of injecting zero-sequence voltage. Thus, the current zero crossing distortion can be alleviated to the greatest extent when injecting zero sequence voltage over modulation.
The steady-state experimental results of SVPWM, ZCC-SVM (Zero-Crossing Clamped SVPWM), and the proposed method are compared. When the modulation index is 0.5, the distortion of the SVPWM modulation strategy in the current zero crossing region is obvious, while the input current of ZCC-SVM and the proposed modulation method has no obvious zero crossing distortion. When the modulation index is low, the suppression effect of current zero crossing distortion of ZCC-SVM and the proposed modulation method is almost the same, because in the region of current zero crossing, the injection of zero sequence voltage will not cause over-modulation. When the modulation index is 0.9, the zero-sequence voltage injected by the ZCC-SVM method to suppress zero crossing distortion will be over-modulated. Compared with ZCC-SVM, since the proposed modulation algorithm adopts the minimum synthesis error method, the low-frequency THD (Total Harmonic Distortion) is reduced from 3.64% to 3.04%, the high-frequency THD is reduced from 5.34% to 4.56%, and the 5th and 7th harmonics of the input current are significantly reduced.

Key words： Vienna rectifier modulation method neutral point voltage balance current zero crossing distortion

Received: 06 June 2022

PACS:

TM461

	Service

	E-mail this article
	Add to my bookshelf
	Add to citation manager
	E-mail Alert
	RSS
	Articles by authors
	Jiang Weidong
	Hu Yebo
	Zhang Qingyan
	Wang Jinping
	Gao Liang

Cite this article:

Jiang Weidong,Hu Yebo,Zhang Qingyan等. Modulation Method of Vienna Rectifier Based on Modulation Wave Decomposition[J]. Transactions of China Electrotechnical Society, 2023, 38(16): 4339-4352.

URL:

https://dgjsxb.ces-transaction.com/EN/10.19595/j.cnki.1000-6753.tces.221055 OR https://dgjsxb.ces-transaction.com/EN/Y2023/V38/I16/4339

[1] 周运红, 张爱民, 黄晶晶, 等. 基于动态事件触发的Vienna整流器模型预测控制[J]. 电工技术学报, 2022, 37(8): 2040-2050.
Zhou Yunhong, Zhang Aimin, Huang Jingjing, et al.Dynamic event-triggered model predictive control for Vienna rectifier[J]. Transactions of China Electro- technical Society, 2022, 37(8): 2040-2050.
[2] 肖蕙蕙, 苏新柱, 郭强, 等. 三相Vienna整流器无网压传感器预测电流控制策略[J]. 电工技术学报, 2021, 36(6): 1304-1312.
Xiao Huihui, Su Xinzhu, Guo Qiang, et al.Predi- ctive current control of three-phase Vienna rectifier without grid voltage sensors[J]. Transactions of China Electrotechnical Society, 2021, 36(6): 1304-1312.
[3] 党超亮, 王飞, 刘丁, 等. 基于优选矢量合成的Vienna整流器滑模预测控制[J]. 中国电机工程学报, 2022, 42(23): 8699-8708.
Dang Chaoliang, Wang Fei, Liu Ding, et al.Sliding mode predictive control of Vienna rectifier based on optimal vector synthesis[J]. Proceedings of the CSEE, 2022, 42(23): 8699-8708.
[4] Satpathy A S, Kastha D, Kishore N K.Vienna rectifier-fed squirrel cage induction generator based stand-alone wind energy conversion system[J]. IEEE Transactions on Power Electronics, 2021, 36(9): 10186-10198.
[5] Monteiro A P, Jacobina C B, Bahia F A C, et al. Dual Vienna rectifiers with a single DC-link for wind energy conversion system applications[C]//IEEE Energy Conversion Congress and Exposition (ECCE), Detroit, 2020: 2189-2195.
[6] 郝振洋, 徐子梁, 陈宇, 等. 航空Vienna整流器故障诊断与容错控制[J]. 电工技术学报, 2020, 35(24): 5152-5163.
Hao Zhenyang, Xu Ziliang, Chen Yu, et al.Fault diagnosis and fault tolerant control for aviation Vienna rectifier[J]. Transactions of China Electro- technical Society, 2020, 35(24): 5152-5163.
[7] Adhikari J, Iv P, Panda S K.Reduction of input current harmonic distortions and balancing of output voltages of the Vienna rectifier under supply voltage disturbances[J]. IEEE Transactions on Power Elec- tronic, 2017, 32(7): 5802-5812.
[8] Rajendran G, Vaithilingam C A, Misron N, et al.Voltage oriented controller based Vienna rectifier for electric vehicle charging stations[J]. IEEE Access, 2021, 9: 50798-50809.
[9] Pandey R, Singh B.An electric vehicle charger based on Vienna rectifier and resonant LLC converter[C]// IEEE International Conference on Power Electronics, Drives and Energy Systems (PEDES), Jaipur, India, 2021: 1-6.
[10] 朱文杰, 陈昌松, 段善旭. 一种改善Vienna整流器输入电流品质的载波钳位调制方法[J]. 电工技术学报, 2019, 34(8): 1677-1688.
Zhu Wenjie, Chen Changsong, Duan Shanxu.A carrier-based modulation method with clamped area for input current performance of Vienna rectifier[J]. Transactions of China Electrotechnical Society, 2019, 34(8): 1677-1688.
[11] 杨青松, 石健将. 带中点电位波动的Vienna整流器改进SVPWM策略[J]. 电力电子技术, 2021, 55(7): 130-133.
Yang Qingsong, Shi Jianjiang.Improved SVPWM strategy for Vienna rectifier with midpoint potential fluctuation[J]. Power Electronics, 2021, 55(7): 130-133.
[12] 陈杰, 沈禹廷, 沈佳茜, 等. 三相VIENNA整流器的混合空间矢量脉宽调制策略[J]. 电工技术学报, 2021, 36(增刊2): 665-675.
Chen Jie, Shen Yuting, Shen Jiaqian, et al.Hybrid space vector pulse width modulation strategy for three-phase VIENNA rectifier[J]. Transactions of China Electrotechnical Society, 2021, 36(S2): 665-675.
[13] Hang Lijun, Li Bin, Zhang Ming, et al.Equivalence of SVM and carrier-based PWM in three-phase/ wire/level Vienna rectiﬁer and capability of unbalanced- load control[J]. IEEE Transactions on Industrial Elec- tronics, 2014, 61(1): 20-28.
[14] 李洪亮, 姜建国, 乔树通. 三电平SVPWM与SPWM本质联系及对输出电压谐波的分析[J]. 电力系统自动化, 2015, 39(12): 130-137.
Li Hongliang, Jiang Jianguo, Qiao Shutong.Essential relationship between three-level SVPWM and SPWM and analysis on output voltage harmonic[J]. Auto- mation of Electric Power Systems, 2015, 39(12): 130-137.
[15] Xu Houjian, Yao Wenxin, Shao Shuai.Improved SVPWM schemes for Vienna rectifiers without current distortion[C]//IEEE Energy Conversion Con- gress and Exposition (ECCE), Cincinnati, OH, 2017: 3410-3414.
[16] 王涛, 陈昌松, 段善旭, 等. 用于改善电流过零点畸变的Vienna整流器空间矢量调制策略[J]. 电工技术学报, 2019, 34(18): 3854-3864.
Wang Tao, Chen Changsong, Duan Shanxu, et al.An improved space-vector modulation for Vienna recti- fier to eliminating current distortion around zero crossing point[J]. Transactions of China Electro- technical Society, 2019, 34(18): 3854-3864.
[17] Ding Wenlong, Zhang Chenghui, Gao Feng, et al.A zero-sequence component injection modulation method with compensation for current harmonic mitigation of a Vienna rectifier[J]. IEEE Transactions on Power Electronics, 2019, 34(1): 801-814.
[18] Lee J S, Lee K B.A novel carrier-based PWM method for Vienna rectifier with a variable power factor[J]. IEEE Transactions on Industrial Electronics, 2016, 63(1): 3-12.
[19] Molligoda D, Ceballos S, Pou J, et al.Hybrid modulation strategy for the Vienna rectifier[J]. IEEE Transactions on Power Electronics, 2022, 37(2): 1283-1295.
[20] Wang Tao, Chen Changsong, Liu Peng, et al.A hybrid space-vector modulation method for harmonics and current ripple reduction of interleaved Vienna rectifier[J]. IEEE Transactions on Industrial Elec- tronics, 2020, 67(10): 8088-8099.
[21] Jiang Weidong, Wang Lei, Wang Jinping, et al.A carrier-based virtual space vector modulation with active neutral-point voltage control for a neutral- point-clamped three-level inverter[J]. IEEE Transa- ctions Industrial Electronics, 2018, 65(11): 8687-8696.
[22] 谢路耀, 金新民, 吴学智, 等. 基于零序电压注入与调制波分解的三电平脉宽调制策略[J]. 电工技术学报, 2014, 29(10): 27-37.
Xie Luyao, Jin Xinmin, Wu Xuezhi, et al.Three-level pulse width modulation strategy based on zero- sequence voltage injection and modulation-waves decomposition[J]. Transactions of China Electro- technical Society, 2014, 29(10): 27-37.
[23] 陈鹏飞, 唐芬, 吴学智, 等. 三电平并网变流器中点电位自平衡特性分析及拓扑改进[J]. 电力系统自动化, 2019, 43(24): 171-180.
Chen Pengfei, Tang Fen, Wu Xuezhi, et al.Self- balancing characteristic analysis of neutral point potential and improved topology of three-level grid- connected converter[J]. Automation of Electric Power Systems, 2019, 43(24): 171-180.
[24] 石祥花, 许津铭, 谢少军. 三电平中点钳位变换器电容电压自平衡机理与均压控制策略[J]. 电力系统自动化, 2014, 38(7): 95-100, 111.
Shi Xianghua, Xu Jinming, Xie Shaojun.Natural- capacitor voltage balancing mechanism and voltage balance trategies for 3L-NPC inverters[J]. Auto- mation of Electric Power Systems, 2014, 38(7): 95-100, 111.
[25] Ding Wenlong, Qiu Han, Duan Bin, et al.A novel segmented component injection scheme to minimize the oscillation of DC-link voltage under balanced and unbalanced conditions for Vienna rectifier[J]. IEEE Transactions on Power Electronics, 2019, 34(10): 9536-9551.
[26] Li Xing, Han Jian, Sun Yao, et al.A generalized design framework for neutral point voltage balance of three-phase Vienna rectifiers[J]. IEEE Transactions on Power Electronics, 2019, 34(10): 10221-10232.
[27] 丁文龙, 刘家君, 段彬, 等. VIENNA整流器中点电位振荡抑制与平衡控制研究[J]. 中国电机工程学报, 2017, 37(24): 7284-7293, 7443.
Ding Wenlong, Liu Jiajun, Duan Bin, et al.Investi- gation of neutral-point voltage oscillation suppression and balancing control in VIENNA rectifiers[J]. Pro- ceedings of the CSEE, 2017, 37(24): 7284-7293, 7443.
[28] 赵志宏, 吴佳衡, 冯义龙, 等. Vienna整流器输入电流畸变与中点电位振荡综合优化调制策略研究[J]. 中国电机工程学报, 2022, 42(15): 5685-5697.
Zhao Zhihong, Wu Jiaheng, Feng Yilong, et al.Com- prehensive study on modulation strategy for Vienna rectifier input current distortion and midpoint potential oscillation[J]. Proceedings of the CSEE, 2022, 42(15): 5685-5697.