基于双层凹型集磁器的管件电磁胀形电磁力特性及变形行为研究

doi:10.19595/j.cnki.1000-6753.tces.222324

摘要
图/表
参考文献
相关文章 (15)

全文: PDF (2458 KB)
输出: BibTeX | EndNote (RIS)

摘要

针对传统管件电磁胀形存在管件壁厚减薄严重和变形不均匀等问题,本文提出基于双层凹型集磁器结构的单线圈管件电磁成形方法,通过径向电磁力场分布的调控和轴向电磁力的协同加载,为同时抑制管件减薄和改善变形均匀性提供了新的技术途径。为验证该方法的有效性,基于电磁-结构场耦合数值模型,对比探究了有无双层凹型集磁器下轴径电磁力分布特性、管件壁厚减薄量以及轴向变形均匀性等关键物理量的变化规律,并研究了集磁器的内凹高度对管件成形行为的影响。仿真结果表明,与传统管件电磁胀形方法相比,新方法下管件壁厚减薄量可从22.07%降低至8.30%,且轴向均匀性提高2.31倍。

	服务

	把本文推荐给朋友
	加入我的书架
	加入引用管理器
	E-mail Alert
	RSS
	作者相关文章
	邵子豪
	吴伟业
	汪晨鑫
	邱立

关键词 ：电磁成形, 电磁力, 集磁器, 变形行为

Abstract：

Electromagnetic forming technology has significant advantages over mechanical processing technology in the processing of light alloy materials and is an important way to realize energy saving and emission reduction in aerospace, automobile manufacturing and other fields. However, the traditional electromagnetic tube expansion process has the defects of serious wall thinning and uneven axial deformation. Based on the traditional electromagnetic tube expansion system, this paper proposed a novel type of double-layer field shaper to regulate the distribution of magnetic field and electromagnetic force.
The new field shaper structure can adjust the radial electromagnetic force distribution characteristic from “small at the ends, large in the middle” mode to “large at the ends, small in the middle” mode. And the smaller axial electromagnetic force at the end of the tube can be adjusted to a larger electromagnetic force. The adjustment of the radial electromagnetic force field distribution can weaken the radial electromagnetic force in the middle of the formed tube, thus changing the deformation shape of the tube and improving the characteristics of uneven axial deformation of the tube; the adjustment of the axial electromagnetic force field distribution can promote the flow of the material at the end of the tube to the middle area, compensating for the reduction of the wall thickness of the tube due to radial expansion, thus suppressing the wall thickness thinning phenomenon of the tube. To verify the effectiveness of the double-layer field shaper, the finite element model of electromagnetic coupling structure for the electromagnetic tube expansion system was established by using COMSOL software. In this paper, the change laws of the key physical quantities, such as, the electromagnetic force distribution, the axial deformation uniformity and the wall thickness thinning amount were compared and studied under the condition with or without field shaper. On this basis, the influence of the inner cavity depth of the field shaper on the forming effect of tubes was further explored.
The simulation results show that the new field shaper structure improves the axial uniformity by 2.31 times compared with the traditional expansion process, and reduces the wall thickness thinning from 22.07% to 8.30%. The effectiveness of the new field shaper structure in improving the wall thickness thinning and uneven axial deformation of tubes was verified. In addition, increasing the concave height of field shaper is helpful to restrain the wall thinning of tubes, and increase the axial uniformity in a certain range. However, with the further increase of the concave height of field shaper, the radial and axial force fields in the tube forming area are further regulated, the axial uniformity will slightly decrease, but it is still significantly better than the traditional tube expansion effect. It is worth mentioning that the bulging method proposed in this paper adopts single drive coil with simple structure and convenient toolingcompared to multi-coil electromagnetic forming systems. The actual effect of the bulging method will be further verified from the experimental level in the future.

Key words： Electromagnetic forming electromagnetic force magneticfield shaper deformation behavior

收稿日期: 2022-12-12

PACS:

TM154

基金资助:

国家自然科学基金资助项目（51877122）

通讯作者: 邱立, 男,1984年生,博士,副教授,研究方向电磁成形。E-mail：Doctor_QiuL@163.com

作者简介: 邵子豪, 男,1999年生,硕士研究生,研究方向电磁成形。E-mail：shaozihao1999@163.com

引用本文:

邵子豪, 吴伟业, 汪晨鑫, 邱立. 基于双层凹型集磁器的管件电磁胀形电磁力特性及变形行为研究[J]. 电工技术学报, 0, (): 9004-4. Shao Zihao, Wu Weiye, Wang Chenxin, Qiu Li. Electromagnetic Force and Formability Analysis of Tube Electromagnetic Bulging Based on Double-LayerConcave Magnetic Field Shaper. Transactions of China Electrotechnical Society, 0, (): 9004-4.

链接本文:

https://dgjsxb.ces-transaction.com/CN/10.19595/j.cnki.1000-6753.tces.222324 https://dgjsxb.ces-transaction.com/CN/Y0/V/I/9004

[1] Zhou Bo, Liu Bo, Zhang Shengen.The advancement of 7XXX series aluminum alloys for aircraft structures: a review[J]. Metals, 2021, 11(5): 718.
[2] Psyk V, Risch D, Kinsey B L, et al.Electromagnetic forming—a review[J]. Journal of Materials Processing Technology, 2011, 211(5): 787-829.
[3] Li Xiaoxiang, Cao Quanliang, Lai Zhipeng, et al.Bulging behavior of metallic tubes during the electromagnetic forming process in the presence of a background magnetic field[J]. Journal of Materials Processing Technology, 2020, 276: 116411.
[4] Ouyang Shaowei, Li Changxing, Du Limeng, et al.Electromagnetic forming of aluminum alloy sheet metal utilizing a low-frequency discharge: a new method for attractive forming[J]. Journal of Materials Processing Technology, 2021, 291: 117001.
[5] 邱立, 李彦涛, 苏攀, 等. 电磁成形中电磁技术问题研究进展[J]. 电工技术学报, 2019, 34(11): 2247-2259.
Qiu Li, Li Yantao, Su Pan, et al.Research on electromagnetic problems in electromagnetic forming process[J]. Transactions of China Electrotechnical Society, 2019, 34(11): 2247-2259.
[6] Tang Yinghao, Li Xiaoxiang, Zhang Yi, et al.Design of pulsed magnet for adjusting the residual stress field in large-size aluminum alloy rings[J]. IEEE Transactions on Applied Superconductivity, 2022, 32(6): 1-5.
[7] Pawar S, Kore S D.Electromagnetic forming and perforation of Al tubes[J].Journal of Mechanical Science and Technology, 2019, 33(12): 5999-6007.
[8] Qiu Li, Yu Yijie, Wang Ziwei, et al.Analysis of electromagnetic force and deformation behavior in electromagnetic forming with different coil systems[J]. International Journal of Applied Electromagnetics and Mechanics, 2018, 57(3): 337-345.
[9] Li Zhangzhe, Han Xiaotao, Cao Quanliang, et al.Design, fabrication, and test of a high-strength uniform pressure actuator[J]. IEEE Transactions on Applied Superconductivity, 2016, 26(4): 1-5.
[10] Li Xiaoxiang, Cao Quanliang, Lai Zhipeng, et al.Bulging behavior of metallic tubes during the electromagnetic forming process in the presence of a background magnetic field[J]. Journal of Materials Processing Technology, 2020, 276: 116411.
[11] 熊奇, 周丽君, 杨猛, 等. 单脉冲电磁成形中洛伦兹力在时间上的双向竞争关系及其对成形效果的影响[J]. 电工技术学报, 2022, 37(14):3453-3463
Xiong Qi, Zhou Lijun, Yang Meng, et al.The two-way competitive relationship of Lorentz force in time in single pulse electromagnetic forming and its influence on forming effect[J]. Transactions of China Electrotechnical Society, 2022, 37(14):3453-3463
[12] Yu Haiping, Xu Zhidan, Fan Zhisong, et al.Mechanical property and microstructure of aluminum alloy-steel tubes joint by magnetic pulse welding[J]. Materials Science and Engineering: A, 2013, 561: 259-265.
[13] 熊奇, 朱鑫辉, 赵翔, 等. AZ31镁合金管件电磁吸引式成形动态特性研究[J]. 电工技术学报, 2023, 38(10): 2577-2588, 2636.
Xiong Qi, Zhu Xinhui, Zhao Xiang, et al.Research of dynamic characteristics in electromagnetic attraction forming of AZ31 magnesium alloy tube[J]. Transactions of China Electrotechnical Society, 2023, 38(10): 2577-2588, 2636.
[14] 张望, 王于東, 李彦涛, 等. 基于双向电磁力加载的管件电磁翻边理论与实验[J]. 电工技术学报, 2021, 36(14): 2904-2911
Zhang Wang, Wang Yudong, Li Yantao, et al.Theory and experiment of tube electromagnetic flanging based on bidirectional electromagnetic force loading[J]. Transactions of China Electrotechnical Society, 2021, 36(14): 2904-2911
[15] Ouyang Shaowei, Wang Chen, Li Changxing, et al.Improving the uniformity and controllability of tube deformation via a three-coil forming system[J].The International Journal of Advanced Manufacturing Technology, 2021, 114(5/6): 1533-1544.
[16] Qiu Li, Li Yantao, Yu Yijie, et al.Electromagnetic force distribution and deformation homogeneity of electromagnetic tube expansion with a new concave coil structure[J]. IEEE Access, 2019, 7: 117107-117114.
[17] Zhang Xiao, Ouyang Shaowei, Li Xiaoxiang, et al.Effect of pulse width of middle-coil current on deformation behavior in electromagnetic tube forming under two-stage coils system[J].The International Journal of Advanced Manufacturing Technology, 2020, 110(5/6): 1139-1152.
[18] 邱立, 杨新森, 常鹏, 等. 双线圈轴向压缩式管件电磁胀形电磁力分布规律与管件成形性能研究[J]. 电工技术学报, 2019, 34(14): 2855-2862.
Qiu Li, Yang Xinsen, Chang Peng, et al.Electromagnetic force distribution and forming performance in electromagnetic tube expansion process with two coils[J]. Transactions of China Electrotechnical Society, 2019, 34(14): 2855-2862.
[19] 邱立, 余一杰, 聂小鹏, 等. 管件电磁胀形过程中的材料变形性能问题与电磁力加载方案[J]. 电工技术学报, 2019, 34(2): 212-218.
Qiu Li, Yu Yijie, Nie Xiaopeng, et al.Study on material deformation performance and electromagnetic force loading in electromagnetic tube expansion process[J]. Transactions of China Electrotechnical Society, 2019, 34(2): 212-218.
[20] Cao Quanliang, Li Liang, Lai Zhipeng, et al.Dynamic analysis of electromagnetic sheet metal forming process using finite element method[J]. The International Journal of Advanced Manufacturing Technology, 2014, 74(1): 361-368.
[21] Ouyang Shaowei, Li Xiaoxiang, Li Changxing, et al.Investigation of the electromagnetic attractive forming utilizing a dual-coil system for tube bulging[J]. Journal of Manufacturing Processes, 2020, 49: 102-115.