Abstract：As the demand for flexibility and efficiency in modern industrial equipment increases, motors often operate under variable speed conditions in real-world industrial applications. This poses challenges for traditional time-domain and frequency-domain fault diagnosis methods. These challenges arise primarily due to the non-linear and non-stationary characteristics of signals under variable speed conditions, which can affect fault feature extraction. Single deep learning models generally require training and test data to follow the same distribution, and domain adaptation or multi-source domain generalization methods are difficult to apply in the absence of target domain and multi-source domain data, limiting their ability to enhance the generalization of single-source domain models. To address these challenges, this study proposes a motor rolling bearing fault transfer diagnosis method that integrates angular domain resampling and feature enhancement. First, to mitigate the issue of time-frequency characteristic offsets in vibration signals under different rotational speeds, angular domain resampling is employed. This technique processes vibration signals at varying speeds, obtaining angular domain vibration signals to minimize the offsets caused by speed changes. Second, to address the generalization limitations of deep learning models, fault data from constant speed conditions are used as the source domain for training the neural network. Covariance loss is introduced to amplify the feature differences among various classes in the source domain data. This allows the network to focus on more informative features for the classification task, thereby improving its generalization capability. Finally, the angular domain vibration signals under variable speed conditions are input into the trained model for fault classification. The effectiveness of the proposed method is validated through several experiments. Initially, the time-frequency characteristics of vibration signals from an actual bearing inner ring fault are examined before and after angular domain resampling. Before resampling, the vibration signal intervals under variable speed conditions show significant variability. However, after resampling, the variability in the vibration intervals is significantly reduced. Furthermore, using t-SNE visualization, the study observes that networks without feature enhancement show slow gradient updates and minimal changes in feature distribution. In contrast, networks with feature enhancement exhibit continuous changes in feature distribution, even as the classification loss decreases, with increasing feature distances. The study also conducts four cross-working condition fault diagnosis experiments, comparing the proposed method with other methods. The results demonstrate that the proposed method improves fault identification accuracy by 35.04% compared to methods without angular domain resampling, especially in rolling element fault identification. When compared to methods without feature enhancement, the proposed method improves accuracy by 7.45%. Additionally, in transfer diagnosis tasks under different load conditions, the proposed method demonstrates high accuracy, recall, and F1 scores. In conclusion, the study finds that: (1) Angular domain resampling effectively reduces time-frequency distribution differences caused by speed variations, proving its applicability and rationality in data preprocessing at different speeds. (2) The feature enhancement strategy, by increasing covariance loss between different class features, amplifies feature differences between various health status signals, enabling the network to capture more distinctive features and significantly improving generalization capability. (3) The proposed method, without requiring target domain data, achieves fault identification accuracy of up to 97.29% under variable speed conditions, demonstrating good robustness under variable load conditions.
王攀攀, 李兴宇, 张成, 韩丽. 基于角域重采样和特征强化的电机滚动轴承故障迁移诊断方法[J]. 电工技术学报, 2025, 40(12): 3905-3916.
Wang Panpan, Li Xingyu, Zhang Cheng, Han Li. Fault Transfer Diagnosis Method for Motor Rolling Bearings Based on Angular Domain Resampling and Feature Enhancement. Transactions of China Electrotechnical Society, 2025, 40(12): 3905-3916.
[1] 迟连强, 张殿海, 赵俊清, 等. 旋转电机轴承电蚀损伤机理与缓解措施研究进展[J]. 电工技术学报, 2024, 39(20): 6409-6430. Chi Lianqiang, Zhang Dianhai, Zhao Junqing, et al.Research progress on the mechanism and mitigation measure of electrical corrosion damage in rotating motor bearings[J]. Transactions of China Electro-technical Society, 2024, 39(20): 6409-6430. [2] 宋向金, 赵文祥. 交流电机信号特征分析的滚动轴承故障诊断方法综述[J]. 中国电机工程学报, 2022, 42(4): 1582-1595. Song Xiangjin, Zhao Wenxiang.A review of rolling bearing fault diagnosis approaches using AC motor signature analysis[J]. Proceedings of the CSEE, 2022, 42(4): 1582-1595. [3] 党永亮, 张玉焜, 祝令瑜, 等. 基于麦克斯韦力-振动耦合的高压油浸式并联电抗器铁心多倍频振动机理研究[J]. 电工技术学报, 2024, 39(增刊1): 117-126. Dang Yongliang, Zhang Yukun, Zhu Lingyu, et al.Study on multi-harmonic vibration mechanism of high-voltage shunt reactor core based on coupling between Maxwell force and vibration[J]. Transactions of China Electrotechnical Society, 2024, 39(S1): 117-126. [4] 郑毅, 王承民, 刘保良, 等. 基于多层级时空图神经网络的风电机组在线异常检测[J]. 电力系统自动化, 2024, 48(5): 107-119. Zheng Yi, Wang Chengmin, Liu Baoliang, et al.Online anomaly detection of wind turbines based on hierarchical spatio-temporal graph neural network[J]. Automation of Electric Power Systems, 2024, 48(5): 107-119. [5] Jahagirdar A C, Gupta K K.Cumulative distribution sharpness profiling based bearing fault diagnosis framework under variable speed conditions[J]. IEEE Sensors Journal, 2021, 21(13): 15124-15132. [6] 唐贵基, 邓飞跃, 张超, 等. 基于倒谱预白化和奇异值分解的滚动轴承故障特征提取方法[J]. 中国电机工程学报, 2014, 34(35): 6355-6361. Tang Guiji, Deng Feiyue, Zhang Chao, et al.Extraction method of rolling bearing fault feature based on cepstrum pre-whitening and singular value decomposition[J]. Proceedings of the CSEE, 2014, 34(35): 6355-6361. [7] Wang Teng, Liu Zheng, Lu Guoliang, et al.Temporal-spatio graph based spectrum analysis for bearing fault detection and diagnosis[J]. IEEE Transactions on Industrial Electronics, 2021, 68(3): 2598-2607. [8] 赵一楠, 剡昌锋, 孟佳东, 等. 自适应窗口旋转优化短时傅里叶变换的变转速滚动轴承故障诊断[J]. 振动工程学报, 2024, 37(6): 1064-1076. Zhao Yinan, Yan Changfeng, Meng Jiadong, et al.Fault diagnosis of rolling bearings under variable speed conditions based on adaptive window rotation optimization short-time Fourier transform[J]. Journal of Vibration Engineering, 2024, 37(6): 1064-1076. [9] 卞文彬, 邓艾东, 刘东川, 等. 基于改进深度残差收缩网络的风电机组滚动轴承故障诊断方法[J]. 机械工程学报, 2023, 59(12): 202-214. Bian Wenbin, Deng Aidong, Liu Dongchuan, et al.Fault diagnosis method of wind turbine rolling bearing based on improved deep residual shrinkage network[J]. Journal of Mechanical Engineering, 2023, 59(12): 202-214. [10] Chen Xiaohan, Yang Rui, Xue Yihao, et al.Deep transfer learning for bearing fault diagnosis: a systematic review since 2016[J]. IEEE Transactions on Instrumentation and Measurement, 2016, 72: 3508221. [11] 杨洁, 万安平, 王景霖, 等. 基于多传感器融合卷积神经网络的航空发动机轴承故障诊断[J]. 中国电机工程学报, 2022, 42(13): 4933-4942. Yang Jie, Wan Anping, Wang Jinglin, et al.Aeroengine bearing fault diagnosis based on con-volutional neural network for multi-sensor infor-mation fusion[J]. Proceedings of the CSEE, 2022, 42(13): 4933-4942. [12] 郑一珍, 牛蔺楷, 熊晓燕, 等. 基于一维卷积神经网络的圆柱滚子轴承保持架故障诊断[J]. 振动与冲击, 2021, 40(19): 230-238, 285. Zheng Yizhen, Niu Linkai, Xiong Xiaoyan, et al.Fault diagnosis of cylindrical roller bearing cage based on 1D convolution neural network[J]. Journal of Vibration and Shock, 2021, 40(19): 230-238, 285. [13] 宫文峰, 陈辉, 张美玲, 等. 基于深度学习的电机轴承微小故障智能诊断方法[J]. 仪器仪表学报, 2020, 41(1): 195-205. Gong Wenfeng, Chen Hui, Zhang Meiling, et al.Intelligent diagnosis method for incipient fault of motor bearing based on deep learning[J]. Chinese Journal of Scientific Instrument, 2020, 41(1): 195-205. [14] 张辉, 戈宝军, 韩斌, 等. 基于GAF-CapsNet的电机轴承故障诊断方法[J]. 电工技术学报, 2023, 38(10): 2675-2685. Zhang Hui, Ge Baojun, Han Bin, et al.Fault diagnosis method of motor bearing based on GAF-CapsNet[J]. Transactions of China Electrotechnical Society, 2023, 38(10): 2675-2685. [15] 宁方立, 王珂, 郝明阳. 融合CNN和ViT的声信号轴承故障诊断方法[J]. 振动与冲击, 2024, 43(3): 158-163, 170. Ning Fangli, Wang Ke, Hao Mingyang.Fault diagnosis method for bearing based on fusing CNN and ViT[J]. Journal of Vibration and Shock, 2024, 43(3): 158-163, 170. [16] 仝钰, 庞新宇, 魏子涵. 基于GADF-CNN的滚动轴承故障诊断方法[J]. 振动与冲击, 2021, 40(5): 247-253, 260. Tong Yu, Pang Xinyu, Wei Zihan.Fault diagnosis method of rolling bearing based on GADF-CNN[J]. Journal of Vibration and Shock, 2021, 40(5): 247-253, 260. [17] Yang Bin, Xu Songci, Lei Yaguo, et al.Multi-source transfer learning network to complement knowledge for intelligent diagnosis of machines with unseen faults[J]. Mechanical Systems and Signal Processing, 2022, 162: 108095. [18] Xiao Dengyu, Huang Yixiang, Zhao Lujie, et al.Domain adaptive motor fault diagnosis using deep transfer learning[J]. IEEE Access, 2019, 7: 80937-80949. [19] 金亮, 闫银刚, 杨庆新, 等. 小样本条件下永磁同步电机深度迁移学习性能预测方法[J]. 电工技术学报, 2023, 38(18): 4921-4931. Jin Liang, Yan Yingang, Yang Qingxin, et al.Prediction method of deep transfer learning per-formance of permanent magnet synchronous motor under the condition of few-shot[J]. Transactions of China Electrotechnical Society, 2023, 38(18): 4921-4931. [20] 罗宏林, 柏林, 侯东明, 等. 有限变工况特征迁移学习方法及其在高速列车轴箱轴承故障诊断中的应用[J]. 仪器仪表学报, 2022, 43(3): 132-145. Luo Honglin, Bo Lin, Hou Dongming, et al.A transfer learning method for bearing fault diagnosis under finite variable working conditions and its application in train axle-box bearings fault diag-nosis[J]. Chinese Journal of Scientific Instrument, 2022, 43(3): 132-145. [21] Tian Jing, Wang Dong, Chen Liang, et al.A stable adaptive adversarial network with exponential adversarial strategy for bearing fault diagnosis[J]. IEEE Sensors Journal, 2022, 22(10): 9754-9762. [22] 宋向金, 孙文举, 刘国海, 等. 深度子领域自适应网络电机滚动轴承跨工况故障诊断[J]. 电工技术学报, 2024, 39(1): 182-193. Song Xiangjin, Sun Wenju, Liu Guohai, et al.Across working conditions fault diagnosis for motor rolling bearing based on deep subdomain adaption network[J]. Transactions of China Electrotechnical Society, 2024, 39(1): 182-193. [23] Chen Liang, Li Qi, Shen Changqing, et al.Adversarial domain-invariant generalization: a generic domain-regressive framework for bearing fault diagnosis under unseen conditions[J]. IEEE Transactions on Industrial Informatics, 2022, 18(3): 1790-1800. [24] Li Jingde, Shen Changqing, Kong Lin, et al.A new adversarial domain generalization network based on class boundary feature detection for bearing fault diagnosis[J]. IEEE Transactions on Instrumentation and Measurement, 2022, 71: 2506909. [25] 王玉静, 夏林, 康守强, 等. 基于多源域异构模型迁移的滚动轴承故障诊断方法[J]. 振动与冲击, 2023, 42(24): 257-266. Wang Yujing, Xia Lin, Kang Shouqiang, et al.A fault diagnosis method of rolling bearings based on multi-source domain heterogeneous model transfer[J]. Journal of Vibration and Shock, 2023, 42(24): 257-266. [26] Lu Siliang, Guo Jie, He Qingbo, et al.A novel contactless angular resampling method for motor bearing fault diagnosis under variable speed[J]. IEEE Transactions on Instrumentation and Measurement, 2016, 65(11): 2538-2550. [27] 褚旭, 鲍泽宏, 许立强, 等. 基于时序卷积残差网络的主动配电系统线路短路故障诊断方案[J]. 电工技术学报, 2023, 38(8): 2178-2190. Chu Xu, Bao Zehong, Xu Liqiang, et al.Fault line diagnosis scheme of active distribution system based on time-sequence convolution residual network[J]. Transactions of China Electrotechnical Society, 2023, 38(8): 2178-2190.
2025, Vol. 40 
