氮化铝/氮化硼复配改性间位芳纶绝缘纸的使役性能及机理分析

doi:10.19595/j.cnki.1000-6753.tces.240796

Abstract
Figure/Table
References (0)
Related Citation (14)

Download: PDF (2881 KB) HTML (1 KB)
Export: BibTeX | EndNote (RIS)

Abstract

Meta-aramid (PMIA) is a unique fiber that possesses exceptional insulation strength and thermodynamic stability. It is widely regarded as an ideal material for the development of the next generation of insulation paper. However, its intrinsic thermal conductivity of 0.21 W/(m·K) is relatively low and may not meet the long-term service requirements in high-temperature environments. To enhance the thermal conductivity and insulation of the PMIA paper, AlN and BN fillers are selected for composite doping modification of PMIA paper. The surfaces of the two fillers are coated with polydopamine (PDA) and modified with a KH550 silane coupling agent to improve the dispersibility of the two fillers. By adjusting the doping ratio, AlN-BN/PMIA composite insulation paper with different concentrations was prepared. The microstructure was characterized and the breakdown strength, conductivity, and thermal conductivity were tested. The effect of two different filler ratios on the insulation and thermal conductivity of the material was studied.
Firstly, the surfaces of the two fillers are coated with polydopamine (PDA) and modified with a KH550 silane coupling agent to enhance their dispersibility. By adjusting the doping ratio, AlN-BN/PMIA composite insulation paper with different concentrations is prepared. Secondly, the microstructure of samples is characterized and the breakdown voltage, conductivity, and thermal conductivity are tested. The influence of the ratio of two fillers on the insulation and thermal conductivity of the material was studied. Thirdly, based on density functional theory, band structure calculation and analysis are conducted, and a design concept of a “stepped charge trap” is proposed. In addition, the composite breakdown model is constructed using the phase field method, explaining the inherent mechanism of performance improvement.
According to the test results, adding BN to the AlN filler can further improve the matrix structure and fix the damage caused by the high concentration aggregation of AlN. The surface of the composite material appears relatively dense when the AlN/BN ratio is 3:7, with only a small amount of PMIA fibers and fillers precipitated. At a mass fraction of 40%, the breakdown strength of the composite gradually increases as the BN doping ratio increases. At a ratio of AlN/BN of 3:7, the composite paper exhibits its maximum breakdown strength of 186 kV/mm, which is 66.1% higher than that of the pure PMIA sample. Additionally, the conductivity of the composite is at its lowest value during this ratio. On the other hand, at an AlN/BN ratio of 7:3, the thermal conductivity of the composite is optimal, increasing by 213.5% compared to pure PMIA samples. The high aspect ratio structure of BN links it with AlN fillers to form an “thermal conductivity network”, which increases the thermal conductivity.
Energy band structure analysis based on density functional theory suggests that the wide bandgap properties of AlN and BN result in the formation of “stepped traps” at the PMIA interface. This leads to an increased energy barrier for charge transitions and limits the migration of charge carriers. In addition, a phase field simulation model indicates that the introduction of BN can further homogenize the electric field distribution, reduce the degree of local polarization, and thus enhance the insulation performance of the composite system.

Key words： Meta-aramid boron nitride aluminum nitride breakdown strength thermal conductivity

Received: 16 May 2024

PACS:

TM215.6

	Service

	E-mail this article
	Add to my bookshelf
	Add to citation manager
	E-mail Alert
	RSS
	Articles by authors
	Wang Qibin
	Fan Xiaozhou
	Gao Yuxuan
	Yu Xiang
	Liu Yunpeng

Cite this article:

Wang Qibin,Fan Xiaozhou,Gao Yuxuan等. Service Performance and Mechanism of Aluminum Nitride/Boron Nitride Co-Modified Meta-Aramid Insulation Papers[J]. Transactions of China Electrotechnical Society, 0, (): 2492946-2492946.

URL:

https://dgjsxb.ces-transaction.com/EN/10.19595/j.cnki.1000-6753.tces.240796 OR https://dgjsxb.ces-transaction.com/EN/Y0/V/I/2492946

[1] 刘云鹏, 来庭煜, 刘嘉硕, 等. 特高压直流换流阀饱和电抗器振动声纹特性与松动程度声纹检测方法[J]. 电工技术学报, 2023, 38(5): 1375-1389.
Liu Yunpeng, Lai Tingyu, Liu Jiashuo, et al.Vibration voiceprint characteristics and looseness detection method of UHVDC converter valve saturable reactor[J]. Transactions of China Electrotechnical Society, 2023, 38(5): 1375-1389.
[2] 刘道生, 周春华, 丁金, 等. 变压器纳米改性油纸复合绝缘研究综述[J]. 电工技术学报, 2023, 38(9): 2464-2479, 2490.
Liu Daosheng, Zhou Chunhua, Ding Jin, et al.Research overview of oil-paper composite insulation modified by nano particles for transformer[J]. Transactions of China Electrotechnical Society, 2023, 38(9): 2464-2479, 2490.
[3] 张文琦, 范晓舟, 李宇轩, 等. 基于分子动力学的芳纶/功能化碳纳米管复合材料体系热力学性能模拟[J]. 电工技术学报, 2024, 39(5): 1510-1523.
Zhang Wenqi, Fan Xiaozhou, Li Yuxuan, et al.Simulation of thermodynamic properties of aramid/functionalized carbon nanotubes composites based on molecular dynamics[J]. Transactions of China Electrotechnical Society, 2024, 39(5): 1510-1523.
[4] 陈学军, 方亚楠, 聂文鹏, 等. 牵引变压器油纸绝缘热老化及仿真模拟研究[J]. 电气工程学报, 2023, 18(3): 109-116.
Chen Xuejun, Fang Yanan, Nie Wenpeng, et al.Study on thermal aging and simulation of oil-paper insulation for traction transformers[J]. Journal of Electrical Engineering, 2023, 18(3): 109-116.
[5] 刘琦, 付楚珺, 于鲜莉, 等. 基于变压器绝缘劣化降级时间预测的绝缘老化评估方法[J]. 高压电器, 2023, 59(3): 116-122.
Liu Qi, Fu Chujun, Yu Xianli, et al.Predicted insulation aging assessment method based on insulation deterioration degradation time of transformer[J]. High Voltage Apparatus, 2023, 59(3): 116-122.
[6] 律方成, 杨瑞, 宋景萱, 等. 极不均匀电场中叠层间位芳纶纸和纤维素纸的局部放电特性对比分析[J/OL]. 华北电力大学学报(自然科学版), 2022: 1-9[2024-05-10]. http://kns.cnki.net/kcms/detail/13.1212.TM.20221226.1751.002.html.
Lü Fangcheng, Yang Rui, Song Jingxuan, et al. Comparison of insulation and partial discharge characteristics of PMIA paper and cellulose paper[J/OL]. Journal of North China Electric Power University (Natural Science Edition), 2022: 1-9[2024-05-10]. http://kns.cnki.net/kcms/detail/13.1212.TM.20221226.1751.002.html.
[7] 律方成, 路修权, 刘贵林, 等. 纳米Al₂O₃-STPP@HACC核壳填料的制备及其对间位芳纶绝缘纸性能的影响[J]. 华北电力大学学报(自然科学版), 2024, 51(2): 112-122.
Lü Fangcheng, Lu Xiuquan, Liu Guilin, et al.Preparation of nano-Al₂O₃-STPP@HACC core-shell filler and its effect on properties of meta-aramid insulating paper[J]. Journal of North China Electric Power University, 2024, 51(2): 112-122.
[8] 李亚莎, 孟凡强, 章小彬, 等. 纳米SiO₂掺杂对有水环境下间位芳纶绝缘纸性能影响的研究[J]. 原子与分子物理学报, 2020, 37(3): 371-377.
Li Yasha, Meng Fanqiang, Zhang Xiaobin, et al.Study on theinfluence of nano-SiO₂ doping on the performance of meta-aramid insulation paper in water environment[J]. Journal of Atomic and Molecular Physics, 2020, 37(3): 371-377.
[9] 张重远, 范名琳, 赵涛, 等. 纤维素颗粒和水分对天然酯绝缘性能影响试验研究[J]. 华北电力大学学报(自然科学版), 2020, 47(3): 41-48.
Zhang Zhongyuan, Fan Minglin, Zhao Tao, et al.Effect of cellulose particle and moisture content on insulation characteristics of natural ester[J]. Journal of North China Electric Power University (Natural Science Edition), 2020, 47(3): 41-48.
[10] Ruan Haoou, Lü Fangcheng, Song Jingxuan, et al.Enhanced thermal conductance and electrical insulation of AlN/PMIA composite paper via nano splitting of matrix and size grading of fillers[J]. Composites Science and Technology, 2022, 224: 109477.
[11] 方立军, 王绪成. 纳米复合掺杂对高温二元熔融盐传热性能影响[J]. 华北电力大学学报(自然科学版), 2022, 49(5): 118-126.
Fang Lijun, Wang Xucheng.Effect of nano-composite doping on heat transfer performance of binary molten salt at high temperature[J]. Journal of North China Electric Power University (Natural Science Edition), 2022, 49(5): 118-126.
[12] 陈向荣, 王启隆, 黄小凡, 等. 硅烷偶联剂改性纳米AlN对碳化硅器件封装用有机硅弹体耐电及老化特性的影响[J]. 电工技术学报, 2022, 37(16): 4235-4249.
Chen Xiangrong, Wang Qilong, Huang Xiaofan, et al.Effect of silane coupling agent modified nano-AlN on electrical and aging properties of silicone elastomer for SiC device packaging[J]. Transactions of China Electrotechnical Society, 2022, 37(16): 4235-4249.
[13] Wu Guanglei, Wang Yiqun, Wang Kuikui, et al.The effect of modified AlN on the thermal conductivity, mechanical and thermal properties of AlN/polystyrene composites[J]. RSC Advances, 2016, 6(104): 102542-102548.
[14] Lü Fangcheng, Yang Rui, Ruan Haoou, et al.Effect of anti-hydrolysis AlN microspheres on the electrical insulation and thermal conductivity of PMIA paper[J]. IEEE Transactions on Dielectrics and Electrical Insulation, 2023, 30(4): 1674-1680.
[15] Yang Rui, Ruan Haoou, Fan Sidi, et al.High thermal conductivity insulating AlN/poly(m-phenylenedi-carbonyl-m-phenylenediamine) paper realized by enhanced compatibility: a selection of appropriate coupling agent[J]. Journal of Physics D: Applied Physics, 2023, 56(44): 445501.
[16] 范勇, 韩笑笑, 陈昊, 等. 氧化锆复配纳米氧化铝杂化聚酰亚胺薄膜的介电性能研究[J]. 绝缘材料, 2013, 46(4): 63-66.
Fan Yong, Han Xiaoxiao, Chen Hao, et al.Dielectric property study of zirconia/nano-alumina hybrid polyimide film[J]. Insulating Materials, 2013, 46(4): 63-66.
[17] 杜伯学, 孔晓晓, 肖萌, 等. 高导热聚合物基复合材料研究进展[J]. 电工技术学报, 2018, 33(14): 3149-3159.
Du Boxue, Kong Xiaoxiao, Xiao Meng, et al.Advances in thermal performance of polymer-based composites[J]. Transactions of China Electrotechnical Society, 2018, 33(14): 3149-3159.
[18] 律方成, 宋景萱, 宋曼青, 等. C₄F₇N/CO₂混合气体中粗糙度对环氧树脂表面闪络特性的影响[J]. 华北电力大学学报(自然科学版), 2023, 50(1): 1-8.
Lü Fangcheng, Song Jingxuan, Song Manqing, et al.Influence of roughness on epoxy resin surface flashover characteristics in C₄F₇N/CO₂ mixed gas[J]. Journal of North China Electric Power University (Natural Science Edition), 2023, 50(1): 1-8.
[19] 倪艳荣, 郭永亮, 李承斌, 等. 纳米掺杂交联聚乙烯复合材料的空间电荷特性研究[J]. 绝缘材料, 2023, 56(3): 33-40.
Ni Yanrong, Guo Yongliang, Li Chengbin, et al.Study on space charge characteristics of nano-doped cross-linked polyethylene composites[J]. Insulating Materials, 2023, 56(3): 33-40.
[20] Guerra V, Wan Chaoying, McNally T. Thermal conductivity of 2D nano-structured boron nitride (BN) and its composites with polymers[J]. Progress in Materials Science, 2019, 100: 170-186.
[21] Liu Zhan, Li Junhui, Liu Xiaohe.Novel functionalized BN nanosheets/epoxy composites with advanced thermal conductivity and mechanical properties[J]. ACS Applied Materials & Interfaces, 2020, 12(5): 6503-6515.
[22] Yang Dan, Kong Xinxin, Ni Yufeng, et al.Novel nitrile-butadiene rubber composites with enhanced thermal conductivity and high dielectric constant[J]. Composites Part A: Applied Science and Manufacturing, 2019, 124: 105447.
[23] Li Gang, Liu Xiaonan, Zhang Daohai, et al.Preparation and properties of polylactide/hydroxyapatite/polydopamine composites[J]. Polymer Engineering & Science, 2018, 58(12): 2256-2263.
[24] Wang Huaiyuan, Sun Liyuan, Wang Rui, et al.Dopamine modification of multiwalled carbon nanotubes and its influences on the thermal, mechanical, and tribological properties of epoxy resin composites[J]. Polymer Composites, 2017, 38(1): 116-125.
[25] 何金秀, 胡继林, 陈博, 等. AlN粉体水解行为及其抗水解改性的研究进展[J]. 中国陶瓷工业, 2022, 29(2): 39-43.
He Jinxiu, Hu Jilin, Chen Bo, et al.Research progress on hydrolysis behavior and hydrolysis resistance modification of AlN powder[J]. China Ceramic Industry, 2022, 29(2): 39-43.
[26] Ruan Haoou, Xie Qing, Lü Fangcheng, et al.Enhanced breakdown strength of BN/ER by the 2D ordinal tiled structure of fillers[J]. IEEE Transactions on Dielectrics and Electrical Insulation, 2021, 28(2): 423-430.
[27] Ruan Haoou, Xie Qing, Song Jingxuan, et al.Effect of organophilic group of coupling agent on the electrical performance of Boron Nitride/meta-aramid composite paper[J]. High Voltage, 2023, 8(4): 760-771.
[28] Ruan Haoou, Yu Xiang, Liu Yunpeng, et al.Fluorinated interface engineering targeting high-performance multifunctional composites of BN/aramid nanofibers[J]. Composites Part A: Applied Science and Manufacturing, 2024, 178: 107975.
[29] Yang Kerong, Chen Weijiang, Zhao Yushun, et al.Enhancing dielectric strength of epoxy polymers by constructing interface charge traps[J]. ACS Applied Materials & Interfaces, 2021, 13(22): 25850-25857.
[30] Zhao Yushun, Xu Yufan, Shen Hao, et al.Introducing chlorine into epoxy resin to modulate charge trap depth in the material[J]. IEEE Transactions on Dielectrics and Electrical Insulation, 2022, 29(5): 1666-1674.
[31] Cai Ziming, Wang Xiaohui, Luo Bingcheng, et al.Nanocomposites with enhanced dielectric permittivity and breakdown strength by microstructure design of nanofillers[J]. Composites Science and Technology, 2017, 151: 109-114.
[32] Shen Zhonghui, Wang Jianjun, Jiang Jianyong, et al.Phase-field modeling and machine learning of electric-thermal-mechanical breakdown of polymer-based dielectrics[J]. Nature Communications, 2019, 10: 1843.
[33] Shen Zhonghui, Wang Jianjun, Lin Yuanhua, et al.High-throughput phase-field design of high-energy-density polymer nanocomposites[J]. Advanced Materials, 2018, 30(2): 1704380.