高压器件封装用有机硅凝胶内气泡对其正极性方波电压下放电特性的影响

doi:10.19595/j.cnki.1000-6753.tces.221798

Abstract
Figure/Table
References
Related Citation (15)

Download: PDF (13368 KB) HTML (1 KB)
Export: BibTeX | EndNote (RIS)

Abstract With the increasing voltage level of high-voltage IGBT modules, the package insulation of modules requires higher reliability. Therefore, the silicone gel with excellent insulation performance and low elastic modulus is widely used in the packaging of high-voltage IGBT modules. However, the bubble defect in silicone gel is the weak insulation link of package insulation. In this paper, the effect of bubble defect on the discharge characteristics of silicone gel under positive square wave voltage is investigated.
Firstly, the needle plate electrode structure is selected to form a local high field area to prevent the direct breakdown of the sample. The silicone gel samples containing bubbles in the specified position are prepared by layered potting. By analyzing the area of bright white spots in the high-definition images of the samples taken by the microscope, the amount of bubbles in the samples is estimated, and the content of bubbles in the prepared samples is determined to be 0%, 32%, 55%, and 74%, respectively. An experimental platform for partial discharge characteristics of silicone gel based on the partial discharge current pulse measurement method is established for the positive repeated square wave voltage consistent with the module operation condition.
Secondly, partial discharge experiments with different bubble contents are carried out under positive repeated square wave voltage. The statistical characteristics of PDIV and PDEV of each sample are analyzed by Weibull distribution. It is found that with the increase of bubble content, the partial discharge inception voltage(PDIV) and partial discharge extinction voltage (PDEV) of silicone gel samples are significantly decreased, especially the PDIV and PDEV of 74% bubble content samples are decreased by 42% and 46%, respectively.
Thirdly, a method to extract the discharge current pulse from the displacement current is proposed, and the obtained discharge current pulse has no distortion and no high-frequency noise. By analyzing the discharge pulses of samples with different bubble content for at least 50 cycles, it is found that with the increase of bubble content in silicone gel from 0% to 74%, the charge amount of a single local discharge in the sample shows an overall increasing trend, the proportion of forward discharge decreases from 55% to 37%, the rising and falling rate of the pulse increase by 3~5 times, and the rise time and fall time of the pulse decrease about 50%.
Finally, the discharge process with air bubbles in the silicone gel and the mechanical explanation of the effect of air bubbles on the discharge characteristics are analyzed. The simulation results show that the field strength in the bubble is larger than that in the silicone gel under the square wave voltage, while the breakdown field strength of the air is smaller. Therefore, the bubble is more prone to discharge than the silicone gel. In addition, part of the gas molecules will diffuse to the high field strength region through the silicone oil, which will also reduce the overall insulation strength of the silicone gel. In the process of partial discharge development, the electric tree inside the silicone gel will pass through the bubble, and the air components will enter the electric tree airway to participate in the discharge process, resulting in the improvement of the carrier mobility inside the electric tree airway, and then lead to the change of the partial discharge pulse waveform. The results of this paper can guide the improvement of silicone gel encapsulation technology and lay a foundation for the detection of bubble amounts in silicone gel.

Key words： IGBT module insulation silicone gel void positive repetitive square wave voltage partial discharge

Received: 23 September 2022

PACS:

TM211

	Service

	E-mail this article
	Add to my bookshelf
	Add to citation manager
	E-mail Alert
	RSS
	Articles by authors
	Li Xuebao
	Liu Xiangchen
	Liu Sijia
	Zhao Zhibin
	Cui Xiang

Cite this article:

Li Xuebao,Liu Xiangchen,Liu Sijia等. Influence of Bubbles on the Discharge Characteristics of Silicone Gel for High Voltage Module Encapsulation under Positive Square Wave Voltage[J]. Transactions of China Electrotechnical Society, 2023, 38(15): 3999-4009.

URL:

https://dgjsxb.ces-transaction.com/EN/10.19595/j.cnki.1000-6753.tces.221798 OR https://dgjsxb.ces-transaction.com/EN/Y2023/V38/I15/3999

[1] 赵子轩, 陈杰, 邓二平, 等. 负载电流对IGBT器件中键合线的寿命影响和机理分析[J]. 电工技术学报, 2022, 37(1): 244-253.
Zhao Zixuan, Chen Jie, Deng Erping, et al.The influence and failure mechanism analysis of the load current on the IGBT lifetime with bond wire failure[J]. Transactions of China Electrotechnical Society, 2022, 37(1): 244-253.
[2] 李辉, 刘人宽, 王晓, 等. 压接型IGBT器件封装退化监测方法综述[J]. 电工技术学报, 2021, 36(12): 2505-2521.
Li Hui, Liu Renkuan, Wang Xiao, et al.Review on package degradation monitoring methods of press-pack IGBT modules[J]. Transactions of China Electrotechnical Society, 2021, 36(12): 2505-2521.
[3] 贺之渊, 陆晶晶, 刘天琪, 等. 柔性直流电网故障电流抑制关键技术与展望[J]. 电力系统自动化, 2021, 45(2): 173-183.
He Zhiyuan, Lu Jingjing, Liu Tianqi, et al.Key technologies and prospect of fault current suppression in flexible DC power grid[J]. Automation of Electric Power Systems, 2021, 45(2): 173-183.
[4] 拓超群, 贺之渊, 徐千鸣, 等. 直流电网潮流控制器研究与应用综述[J]. 电力系统自动化, 2022, 46(6): 173-183.
Tuo Chaoqun, He Zhiyuan, Xu Qianming, et al.Review on research and application of power flow controller of DC grid[J]. Automation of Electric Power Systems, 2022, 46(6): 173-183.
[5] Zhang Jianjia, Shao Shuai, Li Yucen, et al.Arm voltage balancing control of modular multilevel resonant converter[J]. CES Transactions on Electrical Machines and Systems, 2020, 4(4): 303-308.
[6] Koguchi H, Arai T, Kushima T, et al.A 6.5 kV 1000 A IGBT module with side gate HiGT[C]//PCIM Europe 2018; International Exhibition and Conference for Power Electronics, Intelligent Motion, Renewable Energy and Energy Management, Nuremberg, Germany, 2018: 1-7.
[7] van Brunt E, Cheng Lin, O'loughlin M J, et al.27 kV,20 A 4H-SiC n-IGBTs[J]. Materials Science Forum, 2015, 821-823: 847-850.
[8] 李俊杰, 梅云辉, 梁玉, 等. 功率器件高电压封装用复合电介质灌封材料研究[J]. 电工技术学报, 2022, 37(3): 786-792.
Li Junjie, Mei Yunhui, Liang Yu, et al.Study on composite dielectric encapsulation materials for high voltage power device packaging[J]. Transactions of China Electrotechnical Society, 2022, 37(3): 786-792.
[9] 丁娉, 陈磊, 唐毅平, 等. 新型大功率IGBT用硅凝胶的制备及其应用性研究[J]. 绝缘材料, 2014, 47(2): 52-55.
Ding Ping, Chen Lei, Tang Yiping, et al.Preparation and application research of novel silicone gel for high-power IGBT[J]. Insulating Materials, 2014, 47(2): 52-55.
[10] 顼佳宇, 李学宝, 崔翔, 等. 高压大功率IGBT器件封装用有机硅凝胶的制备工艺及耐电性[J]. 电工技术学报, 2021, 36(2): 352-361.
Xu Jiayu, Li Xuebao, Cui Xiang, et al.Preparation process and breakdown properties of silicone gel used for the encapsulation of IGBT power modules[J]. Transactions of China Electrotechnical Society, 2021, 36(2): 352-361.
[11] Semenov I, Gunheim I F, Niayesh K, et al.Investigation of partial discharges in AlN substrates under fast transient voltages[J]. IEEE Transactions on Dielectrics and Electrical Insulation, 2022, 29(2): 745-752.
[12] You Haoyang, Wei Zhuo, Hu Boxue, et al.Partial discharge behaviors in power modules under square pulses with ultrafast dv/dt[J]. IEEE Transactions on Power Electronics, 2021, 36(3): 2611-2620.
[13] Sato M, Kumada A, Hidaka K, et al.Void-free encapsulation technique for semiconductor devices using silicone gel[C]//2013 Annual Report Conference on Electrical Insulation and Dielectric Phenomena, Chenzhen, China, 2014: 921-924.
[14] 冯传均, 王传伟, 戴文峰, 等. 高压模块的有机硅凝胶灌封工艺设计与改进[J]. 电子工艺技术, 2015, 36(1): 51-54.
Feng Chuanjun, Wang Chuanwei, Dai Wenfeng, et al.Silicone gel encapsulation process design and improvement of high-voltage module[J]. Electronics Process Technology, 2015, 36(1): 51-54.
[15] 顼佳宇. 高压大功率IGBT器件封装用有机硅凝胶电气特性的研究与应用[D]. 北京: 华北电力大学(北京), 2021.
[16] Ebke T, Khaddour A, Peier D.Degradation of silicone gel by partial discharges due to different defects[C]// 2000 Eighth International Conference on Dielectric Materials, Measurements and Applications (IEE Conf. Publ. No. 473), Edinburgh, UK, 2002: 202-207.
[17] Finis G, Claudi A.On the electric breakdown behavior of silicone gel at interfaces[J]. IEEE Transactions on Dielectrics and Electrical Insulation, 2008, 15(2): 366-373.
[18] Borghei M, Ghassemi M.Investigation of low-pressure condition impact on partial discharge in micro-voids using finite-element analysis[C]//2020 IEEE Energy Conversion Congress and Exposition (ECCE), Detroit, MI, USA, 2020: 3293-3298.
[19] Li Kaixuan, Zhang Boya, Li Xingwen, et al.The influence of degassing time and curing time on insulation behaviours of silicone gel in IGBT modules[C]//22nd International Symposium on High Voltage Engineering (ISH 2021), Hybrid Conference, Xi'an, China, 2022: 1537-1541.
[20] Li Ye, Li Xuebao, Meng Wei, et al.Influence of N2 pressure on surface discharge characteristics of PEEK under positive repetitive square voltage[J]. High Voltage, 2021, 6(5): 793-804.
[21] 王鹏, 周婉亚, 王科镜, 等. 正弦和重复方波电压下变频电机绝缘局部放电特性对比[J]. 高电压技术, 2016, 42(12): 3895-3900.
Wang Peng, Zhou Wanya, Wang Kejing, et al.Comparison of PD characteristics for inverter-fed motor insulation under inusoidal and repetitive square wave voltage conditions[J]. High Voltage Engineering, 2016, 42(12): 3895-3900.
[22] 王鹏. 方波脉冲电压对局部放电特性及电机绝缘寿命影响机理研究[D]. 成都: 西南交通大学, 2013.
[23] Rizzo G, Romano P, Ala G, et al.Deformation of bubbles in silicon gel insulation under an alternating electric field[C]//2019 IEEE Conference on Electrical Insulation and Dielectric Phenomena (CEIDP), Richland, WA, USA, 2020: 536-539.
[24] 王壮. 真空脱气原理和技术[J]. 真空, 1999, 36(4): 37-41.
Wang Zhuang.Principle and technique of vacuum gas-seperation[J]. Vacuum, 1999, 36(4): 37-41.
[25] DS/IEC 60664-1 Insulation coordination for equipment within low-voltage systems-part 1: principles, requirements and tests[S]. DS, 2002.
[26] Guastavino F, Dardano A, Torello E.Measuring partial discharges under pulsed voltage conditions[J]. IEEE Transactions on Dielectrics and Electrical Insulation, 2008, 15(6): 1640-1648.
[27] Sargazi R, Akbari A, Werle P, et al.A novel wideband partial discharge measuring circuit under fast repetitive impulses of static converters[J]. Measure-ment, 2021, 178: 109353.
[28] 杨昊, 李学宝, 赵志斌, 等. 正极性重复脉冲电压下有机硅凝胶-PI界面的沿面放电特性[J]. 高电压技术, 2022, 48(2): 724-735.
Yang Hao, Li Xuebao, Zhao Zhibin, et al.Surface discharge characteristics of interface between silicone gel and PI under positive repetitive pulse voltage[J]. High Voltage Engineering, 2022, 48(2): 724-735.
[29] Okubo H, Hayakawa N.A novel technique for partial discharge and breakdown investigation based on current pulse waveform analysis[J]. IEEE Transactions on Dielectrics and Electrical Insulation, 2005, 12(4): 736-744.
[30] Fu Pengyu, Zhao Zhibin, Cui Xiang, et al.Partial discharge measurement and analysis in high voltage IGBT modules under DC voltage[J]. CSEE Journal of Power and Energy Systems, 2018, 4(4): 513-523.
[31] Dodd S J, Salvatierra L, Dissado L A, et al.Electrical trees in silicone gel: a combination of liquid and solid behaviour patterns[C]//2013 Annual Report Conference on Electrical Insulation and Dielectric Phenomena, Shenzhen, China, 2014: 1018-1021.
[32] Fu Pengyu, Zhao Zhibin, Li Xuebao, et al.Surface discharge characteristics and initiation mechanism of PEEK in nitrogen under semi-square voltage[J]. AIP Advances, 2018, 8(7): 075322.
[33] Merkel T C, Bondar V I, Nagai K, et al.Gas sorption, diffusion, and permeation in poly(dimethylsiloxane)[J]. Journal of Polymer Science Part B: Polymer Physics, 2000, 38(3): 415-434.
[34] 杜伯学, 张莹, 孔晓晓, 等. 环氧树脂绝缘电树枝劣化研究进展[J]. 电工技术学报, 2022, 37(5): 1128-1135, 1157.
Du Boxue, Zhang Ying, Kong Xiaoxiao, et al.Research progress on electrical tree in epoxy resin insulation[J]. Transactions of China Electrotechnical Society, 2022, 37(5): 1128-1135, 1157.
[35] Yabuuchi W, Wada A, Sasaki S, et al.Electric field strength and tree propagation speed for electrical treeing in silicone gel[C]//International Symposium on Electrical Insulating Materials (ISEIM), Tokyo, Japan, 2020: 474-477.
[36] Nakamura S, Kumada A, Hidaka K, et al.Electrical treeing in silicone gel under repetitive voltage impulses[J]. IEEE Transactions on Dielectrics and Electrical Insulation, 2019, 26(6): 1919-1925.
[37] 顼佳宇, 崔翔, 李学宝, 等. 工频电压下有机硅凝胶的电树枝发展规律及其局部放电特性[J]. 高电压技术, 2021, 47(5): 1796-1804.
Xu Jiayu, Cui Xiang, Li Xuebao, et al.Propagation of electrical tree and characteristic of partial discharge in silicone gel used for the encapsulation in power module[J]. High Voltage Engineering, 2021, 47(5): 1796-1804.
[38] Okubo H, Hayakawa N, Matsushita A.The relationship between partial discharge current pulse waveforms and physical mechanisms[J]. IEEE Electrical Insulation Magazine, 2002, 18(3): 38-45.
[39] Li Xuebao, Cui Xiang, Lu Tiebing, et al.Influence of air pressure on the detailed characteristics of corona current pulse due to positive corona discharge[J]. Physics of Plasmas, 2016, 23(12): 123516.