表嵌式交替极永磁电机拓扑演化及气隙磁场调制效应研究

doi:10.19595/j.cnki.1000-6753.tces.220984

Abstract
Figure/Table
References (27)
Related Citation (15)

Download: PDF (3426 KB) HTML (1 KB)
Export: BibTeX | EndNote (RIS)

Abstract

Compared with traditional surfaced-mounted permanent magnet (SPM) machine, the consequent- pole permanent magnet (CPM) structures show a higher permanent magnet (PM) utilization ratio and comparable torque capability. Thus, the various PM arrangements are developed and studied in recent years. However, the corresponding topology evolution and the underlying air-gap field modulation (AGFM) mechanism are unrevealed. To present an in-depth understanding of their torque production principle, the topology evaluation and their AGFM effect in the surface-inset CPM machines were investigated and compared.
Firstly, topology evaluation of the CPM machines with different PM arrangements was illustrated by adopting PM unit concept. According to their relationship of the rotor modulated teeth and PM pole-pair number, the CPM machines with different pole-pair PMs in a PM unit was developed. Different from conventional CPM configurations share with same PM pole-pair and rotor modulated teeth, the unconventional CPM machines have the unequal number of the PM pole-pair and rotor modulated teeth. Some topological evolution rules can be summarized as: (1) When n (≥2) pole-pair of PMs are included in a PM unit, n typical non-traditional CPM structures can be formed. (2) An unconventional CPM machine with n (≥2) pole-pair of PMs in a PM unit, the maximum number of the rotor modulated teeth is n-1. (3) Because the S pole (or N pole) and the adjacent N and S poles in a PM unit can be replaced by the rotor iron teeth, there are two types of non-traditional CPM structures can be formed when the rotor modulation tooth is 1 in a PM unit.
To identify the different PM arrangement on their air-gap magnetic field, torque contributions of the various air-gap field harmonics were quantified by Maxwell Stress Tensor method (MSTD). The simulation results show that various air-gap field modulated harmonics are responsible for torque generation in three typical CPM machines, which implies that the pronounced AGFM effect can be obtained in conventional and unconventional CPM cases. Besides, compared with other modulated field harmonics, the |Z_r-Z_s| (5^th), 2Z_r (8^th) and |Z_r+Z_s|(13^rd) contributes a relatively higher torque components in conventional CPM machine. However, apart from the |Z_r-Z_s| (5^th), 2Z_r (8^th) and |Z_r+Z_s|(13^rd), the Z_m (2^nd)、|Z_m+Z_s| (7^th) and |Z_m-2Z_s| (16^th) are also participating in torque production. Although more air-gap field harmonics are responsible for torque generation in unconventional CPM structure, its total torque proportion of the modulated field harmonics is lower than the conventional CPM case. This is mainly due to the relatively lower amplitudes of the Z_r (4^th) air-gap flux density in unconventional CPM machines. To confirm the abovementioned analysis, a CPM machine prototype was manufactured. Some tested results on the open-circuit back-EMF and electromagnetic torques were measured and compared with simulations, which verifies the effectiveness of the theoretical and simulated analyses.
Some conclusions can be drawn from the simulation and experimental analyses: (1) Because of the unequal number of the PM pole-pair and rotor modulated teeth, the unconventional CPM machines exhibits a relatively lower Z_r order air-gap flux density and hence resulting a lower torque capability. (2) Although various air-gap field harmonics can be modulated in unconventional CPM structure, the total torque proportion of the modulated field harmonics is less than 2 %, which indicates that the unconventional CPM machine can be seen as a typical traditional PM synchronous machine with only one working harmonic for torque generation. (3) Due to the higher torque proportion of the air-gap field modulation harmonics, the conventional CPM machines show a pronounced AGFM effect than unconventional counterparts.

Key words： Air-gap field modulation effect consequent-pole permanent magnet machine torque quanti- fication

Received: 31 May 2022

PACS:

TM351

	Service

	E-mail this article
	Add to my bookshelf
	Add to citation manager
	E-mail Alert
	RSS
	Articles by authors
	Li Ya
	Zhou Qinglin
	Ding Shichuan
	Li Wei
	Hang Jun

Cite this article:

Li Ya,Zhou Qinglin,Ding Shichuan等. Investigation of Topologies Evolution and Air-Gap Field Modulation Effect on Surface-Inset Consequent-Pole PM Machines[J]. Transactions of China Electrotechnical Society, 2023, 38(12): 3188-3198.

URL:

https://dgjsxb.ces-transaction.com/EN/10.19595/j.cnki.1000-6753.tces.220984 OR https://dgjsxb.ces-transaction.com/EN/Y2023/V38/I12/3188

[1] 黄海林, 李大伟, 曲荣海, 等. 磁齿轮复合永磁电机拓扑及应用综述[J]. 电工技术学报, 2022, 37(6): 1381-1397.
Huang Hailin, Li Dawei, Qu Ronghai, et al.A review of magnetic geared machines: topologies and appli-cations[J]. Transactions of China Electrotechnical Society, 2022, 37(6): 1381-1397.
[2] 罗俊, 寇宝泉, 杨小宝. 双交替极横向磁通直线电机的优化与设计[J]. 电工技术学报, 2020, 35(5): 991-1000.
Luo Jun, Kou Baoquan, Yang Xiaobao.Optimization and design of dual-consequent-pole transverse flux linear machine[J]. Transactions of China Electro-technical Society, 2020, 35(5): 991-1000.
[3] Li Ya, Yang Hui, Lin Heyun, et al.Investigation of double-side field modulation mechanism in consequent-pole PM machines with concentrated windings[J]. IEEE Transactions on Energy Conversion, 2021, 36(3): 1635-1648.
[4] Li J, Wang K, Liu C.Torque improvement and cost reduction of permanent magnet machines with a dovetailed consequent-pole rotor[J]. IEEE Transa-ctions on Energy Conversion, 2018, 33: 1628-1640.
[5] 许孝卓, 孙震, 汪旭东, 等. Halbach交替极永磁同步直线电机特性分析[J]. 电工技术学报, 2019, 34(9): 1825-1833.
Xu Xiaozhuo, Sun Zhen, Wang Xudong, et al.Characteristic of a novel permanent magnet linear synchronous motor with Halbach array consequent-pole[J]. Transactions of China Electrotechnical Society, 2019, 34(9): 1825-1833.
[6] Watahiki T, Toriumi Y, Miki I. A consequent pole motor with novel pole structure[C]//IEEE2018 Inter-national Symposium on Power Electronics, Electrical Drives, Automation and Motion (SPEEDAM), Amalfi, Italy: 1136-1140.
[7] Wu Leilei, Qu Ronghai. Comparison of conventional and consequent pole interior permanent magnet machines for electric vehicle application[C]//IEEE2014 17th International Conference on Electrical Machines and Systems (ICEMS), Hangzhou, China, 70-74.
[8] 樊英, 谭超. 内置式交替极永磁同步电机性能及机理研究[J]. 电工技术学报, 2018, 33(11): 2414-2422.
Fan Ying, Tan Chao.Analysis of electromagnetic performance and principles in inserted consequent-pole permanent magnet synchronous machines[J]. Transactions of China Electrotechnical Society, 2018, 33(11): 2414-2422.
[9] Chiu M T, Chiang J A, Lin C H.Design and optimi-zation of a novel V-type consequent-pole interior permanent magnet synchronous motor for applying to refrigerant compressor[C]//2018 21st International Conference on Electrical Machines and Systems (ICEMS), Jeju, Korea (South), DOI: 10.23919/ICEMS.2018.8549357.
[10] Kolehmainen J.Optimal dovetail permanent magnet rotor solutions for various pole numbers[J]. IEEE Transactions on Industrial Electronics, 2010, 57(1): 70-77.
[11] 许孝卓, 封海潮, 艾立旺, 等. U型永磁凸极直线电机结构及电磁特性[J]. 电工技术学报, 2021, 36(6): 1179-1189.
Xu Xiaozhuo, Feng Haichao, Ai Liwang, et al.Structure and electromagnetic characteristics of U-shaped permanent magnet salient pole linear motor[J]. Transactions of China Electrotechnical Society, 2021, 36(6): 1179-1189.
[12] Liu Wenbo, Lipo T A.Analysis of consequent pole spoke type vernier permanent magnet machine with alternating flux barrier design[J]. IEEE Transactions on Industry Applications, 2018, 54(6): 5918-5929.
[13] 梁子漪, 曲荣海, 李大伟, 等. 一种交替极切向励磁游标永磁电机的分析与设计[J]. 电工技术学报, 2020, 35(15): 3173-3181.
Liang Ziyi, Qu Ronghai, Li Dawei, et al.Analysis of a consequent-pole spoke-array vernier permanent magnet machine[J]. Transactions of China Elect-rotechnical Society, 2020, 35(15): 3173-3181.
[14] Palomo R E Q, Gwozdziewicz M. Effect of demag-netization on a consequent pole IPM synchronous generator[J]. Energies, 2020, 13(23): 6371.
[15] Zhang Lin, Wang Kai, Li Jian, et al.Comparison study of interior permanent magnet synchronous machine with conventional and consequent pole rotor[C]//2019 22nd International Conference on Electrical Machines and Systems (ICEMS), Harbin, 2019: 1-5.
[16] Wang K, Li J, Zhu S S, et al.Novel hybrid-pole rotors for consequent-pole PM machines without unipolar leakage flux[J]. IEEE Transactions on Industrial Electronics, 2019, 66(9): 6811-6823.
[17] Dajaku G.Open-circuit air-gap field calculation of a new PM machine having a combined SPM and spoke-type magnets[J]. IEEE Transactions on Magnetics, 2020, 56(6): 1-9.
[18] Xu Gaohong, Zhao Wenxiang, Liu Guohai, et al.Torque performance improvement of consequent-pole PM motors with hybrid rotor configuration[J]. IEEE Transactions on Transportation Electrification, 2021, 7(3): 1561-1572.
[19] Li Dawei, Qu Ronghai, Li Jian.Topologies and analysis of flux-modulation machines[C]//2015 IEEE Energy Conversion Congress and Exposition, Montreal, QC, Canada, 2015: 2153-2160.
[20] Chen Yiduan, Fu Weinong, Weng Xu.A concept of general flux-modulated electric machines based on a unified theory and its application to developing a novel doubly-fed dual-stator motor[J]. IEEE Transa-ctions on Industrial Electronics, 2017, 64(12): 9914-9923.
[21] Cheng Ming, Han Peng, Hua Wei.General airgap field modulation theory for electrical machines[J]. IEEE Transactions on Industrial Electronics, 2017, 64(8): 6063-6074.
[22] 程明, 文宏辉, 曾煜, 等. 电机气隙磁场调制行为及其转矩分析[J]. 电工技术学报, 2020, 35(5): 921-930.
Cheng Ming, Wen Honghui, Zeng Yu, et al.Analysis of airgap field modulation behavior and torque component in electric machines[J]. Transactions of China Electrotechnical Society, 2020, 35(5): 921-930.
[23] Zhu W, Pekarek S, Fahimi B, et al.Investigation of force generation in a permanent magnet synchronous machine[J]. IEEE Transactions on Energy Conversion, 2007, 22(3): 557-565.
[24] Huang L R, Feng J H, Guo S Y, et al.Analysis of torque production in variable flux reluctance machines[J]. IEEE Transactions on Energy Con-version, 2017, 32(4): 1297-1308.
[25] Zhu Shengdao, Ji Jinghua, Zhao Wenxiang, et al.Vibration reduction design of consequent pole PM machine by symmetrizing local and global magnetic field[J]. IEEE Transactions on Industrial Electronics, 2023, 70(1): 243-254.
[26] Li J, Wang K, Li F, et al.Elimination of even-order harmonics and unipolar leakage flux in consequent-pole PM machines by employing N-S-iron-S-N-iron rotor[J]. IEEE Transactions on Industrial Electronics, 2019, 66(3): 1736-1747.
[27] Li J, Wang K, Liu C, et al.Elimination of unipolar leakage flux in consequent-pole PM machines by employing novel pole sequence[J]. IEEE Transactions on Magnetics, 2018, 54(11): 1-5.