基于失效物理的功率器件疲劳失效机理

doi:10.19595/j.cnki.1000-6753.tces.171414

Abstract
Figure/Table
References
Related Citation (15)

Download: PDF (49712 KB) HTML (1 KB)
Export: BibTeX | EndNote (RIS)

Abstract Fatigue failures of the materials of power devices are accelerated because power devices always suffer continuous variations of temperature and stress in their long-term operations. Meanwhile, with the development of renewable energy technology, the demand of power density of power electronic converter is becoming higher and higher. It presents a new challenge for designing high reliability power devices. Therefore, intensive studies of fatigue failure mechanism of power devices are important to the optimizing design of packages, material selection and manufacturing technique, and also the premise of designing high reliable power devices. Physics-of-Failure (PoF) is a vital method to study the fatigue failure, which can predicate the reliability via modeling and simulating based on the analysis of the failure process and mechanism. In this review, the basic theories of fatigue failure are introduced first. Then, the fatigue mechanism and main research progress of bond wires and solder layer of power devices are introduced from the aspects of experiment, simulation, analytical model and fatigue mode. On this basis, the whole process of fatigue to failure of power devices is analyzed. Finally, from three aspects of multi-environmental stress, dynamic loading and reliability design, the research directions of power electronics reliability based on PoF are discussed.

Key words： Physics-of-failure power devices reliability bond wires solder layer

Received: 12 October 2017 Published: 01 March 2019

PACS:	TN303
	TM23

	Service

	E-mail this article
	Add to my bookshelf
	Add to citation manager
	E-mail Alert
	RSS
	Articles by authors
	Wang Xuemei
	Zhang Bo
	Wu Haiping

Cite this article:

Wang Xuemei,Zhang Bo,Wu Haiping. A Review of Fatigue Mechanism of Power Devices Based on Physics-of-Failure[J]. Transactions of China Electrotechnical Society, 2019, 34(4): 717-727.

URL:

https://dgjsxb.ces-transaction.com/EN/10.19595/j.cnki.1000-6753.tces.171414 OR https://dgjsxb.ces-transaction.com/EN/Y2019/V34/I4/717

[1] Yang S, Bryant A, Mawby P, et al.An industry based survey of reliability in power electronic converters[J]. IEEE Transactions on Industry Applications, 2011, 47(3): 1441-1451.
[2] Wang H, Liserre M, Blaabjerg F.Toward reliable power electronics: challenges, design tools, and opportunities[J]. IEEE Industrial Electronics Magazine, 2013, 7(2): 17-26.
[3] Choi U M, Blaabjerg F, Lee K B.Study and handling methods of power IGBT module failures in power electronic converter systems[J]. IEEE Transactions on Power Electronics, 2015, 30(5): 2517-2533.
[4] Wang H, Liserre M, Blaabjerg F, et al.Transitioning to physics-of-failure as a reliability driver in power electronics[J]. IEEE Journal of Emerging & Selected Topics in Power Electronics, 2014, 2(1): 97-114.
[5] JEDEC. JEP148 Reliability Qualification of Semi- conductor Devices Based on Physics of Failure Risk and Opportunity Assessment[S]. 2014.
[6] Matic Z, Sruk V.The Physics-of-failure approach in reliability engineering[C]//30th International Conference on Information Technology Interfaces, Dubrovnik, Croatia, 2008: 745-750.
[7] Dietrich P.Trends in automotive power semicon- ductor packaging[J]. Microelectronics Reliability, 2013, 53(9-11): 1681-1686.
[8] Yang S, Xiang D, Bryant A, et al.Condition monitoring for device reliability in power electronic converters: a review[J]. IEEE Transactions on Power Electronics, 2010, 25(11): 2734-2752.
[9] Yang L, Agyakwa P A, Johnson C M.Physics- of-failure lifetime prediction models for wire bond interconnects in power electronic modules[J]. IEEE Transactions on Device & Materials Reliability, 2013, 13(1): 9-17.
[10] Lee W.Solder joint fatigue models: review and applicability to chip scale packages[J]. Micro- electronics Reliability, 2000, 40(2): 231-244.
[11] Ciappa M.Lifetime prediction on the base of mission profiles[J]. Microelectronics Reliability, 2005, 45(9-11): 1293-1298.
[12] Vianco P T.Lead-free solder interconnection reliability[M]. Detroit: ASM International, 2005.
[13] McPherson J M. Reliability physics and engineering: Time-to-failure modeling[M]. New York: Springer, 2010.
[14] Lutz J, Schlangenotto H, Scheuermann U, et al.Semiconductor power devices: physics, characteri- stics, reliability[M]. Berlin: Springer, 2011.
[15] Ramminger S, Seliger N, Wachutka G.Reliability model for Al wire bonds subjected to heel crack failures[J]. Microelectronics Reliability, 2000, 40(8-10): 1521-1525.
[16] Celnikier Y, Benabou L, Dupont L, et al.Investigation of the heel crack mechanism in Al connections for power electronics modules[J]. Microelectronics Reliability, 2011, 51(5): 965-974.
[17] Medjahed H, Vidal P, Nogarede B.Thermo- mechanical stress of bonded wires used in high power modules with alternating and direct current modes[J]. Microelectronics Reliability, 2012, 52(6): 1099-1104.
[18] Held M, Jacob P, Nicoletti G, et al.Fast power cycling test for insulated gate bipolar transistor modules in traction application[J]. International Journal of Electronics, 1999, 86(10): 1193-1204.
[19] Czerny B, Lederer M, Nagl B, et al.Thermo- mechanical analysis of bonding wires in IGBT modules under operating conditions[J]. Micro- electronics Reliability, 2012, 52(9-10): 2353-2357.
[20] Liu Y.Power electronic packaging[M]. New York: Springer, 2012.
[21] Lu H, Bailey C, Yin C.Design for reliability of power electronics modules[J]. Microelectronics Reliability, 2009, 49(9): 1250-1255.
[22] Celnikier Y, Dupont L, Hervé E, et al.Optimization of wire connections design for power electronics[J]. Microelectronics Reliability, 2011, 51(9-11): 1892-1897.
[23] Czerny B, Paul I, Khatibi G, et al.Experimental and analytical study of geometry effects on the fatigue life of Al bond wire interconnects[J]. Micro- electronics Reliability, 2013, 53(9-11): 1558-1562.
[24] Ciappa M.Selected failure mechanisms of modern power modules[J]. Microelectronics Reliability, 2002, 42(4-5): 653-667.
[25] Huang H, Mawby P.A lifetime estimation technique for voltage source inverters[J]. IEEE Transactions on Power Electronics, 2013, 28(8): 4113-4119.
[26] Wu K, Lin S, Hung T, et al.Reliability assessment of packaging solder joints under different thermal cycle loading rates[J]. IEEE Transactions on Device & Materials Reliability, 2015, 15(3): 437-442.
[27] Zhuang W D, Chang P C, Chou F Y, et al.Effect of solder creep on the reliability of large area die attachment[J]. Microelectronics Reliability, 2001, 41(12): 2011-2021.
[28] Bouarroudj M, Khatir Z, Ousten J P, et al.Comparison of stress distributions and failure modes during thermal cycling and power cycling on high power IGBT modules[C]//European Conference on Power Electronics and Applications, Aalborg, Denmark, 2007: 1-10.
[29] Lutz J, Herrmann T, Feller M, et al.Power cycling induced failure mechanisms in the viewpoint of rough temperature environment[C]//5th International Con- ference on Integrated Power Electronics Systems, Nuremberg, Germany, 2008: 1-4.
[30] Zheng Libing, Han Li, Liu Jun, et al.Investigation of the temperature character of IGBT solder delamination based the 3-D thermal-electro coupling FEM[C]// Power and Energy Engineering Conference (APPEEC), Chengdu, China, 2010: 1-4.
[31] Yamada S E.A bonded joint analysis for surface mount components[J]. Journal of Electronic Pack- aging, 1992, 114(1): 1-7.
[32] Fleischer A S, Chang L H, Johnson B C.The effect of die attach voiding on the thermal resistance of chip level packages[J]. Microelectronics Reliability, 2006, 46(5): 794-804.
[33] Katsis D C, Vanwyk J D.A thermal, mechanical, and electrical study of voiding in the solder die-attach of power MOSFETs[J]. IEEE Transactions on Com- ponents & Packaging Technologies, 2006, 29(1): 127-136.
[34] Gao Bing, Yang Fan, Chen Minyou, et al.A temperature gradient based condition estimation method for IGBT module[J]. IEEE Transactions on Power Electronics, 2016, 32(3): 2227-2242.
[35] Chen Y, Wu X, Fedchenia I, et al.A comprehensive analytical and experimental investigation of wire bond life for IGBT modules[C]//27th Annual IEEE on Applied Power Electronics Conference and Exposition, Orlando, America, 2012: 2298-2304.
[36] Czerny B, Paul I, Khatibi G, et al.Influence of wirebond shape on its lifetime with application to frame connections[C]//14th International Conference on Thermal, Mechanical and Multi-Physics Simulation and Experiments in Microelectronics and Microsystems, Wroclaw, Poland, 2013: 1-5.
[37] Lu H, Tilford T, Newcombe D R.Lifetime prediction for power electronics module substrate mount-down solder interconnect[C]//International Symposium on High Density Packaging and Microsystem Integration, Shanghai, China, 2007: 1-6.
[38] 郑利兵, 韩立, 刘钧, 等. 基于三维热电耦合有限元模型的IGBT失效形式温度特性研究[J]. 电工技术学报, 2011, 26(7): 242-246.
Zheng Libing, Han Li, Liu Jun, et al.Investigation of the temperature character of IGBT failure mode based on 3D thermal-electro coupling FEM[J]. Transactions of China Electrotechnical Society, 2011, 26(7): 242-246.
[39] Tian Tian, Liang Lin, Xin Wei, et al.Influences of DBC metal layout on the reliability of IGBT power modules[C]//IEEE 3rd Workshop on Wide Bandgap Power Devices and Applications, Blacksburg, America, 2015: 166-169.
[40] Xu Ling, Wang Miaocao, Zhou Yang, et al.An optimal structural design to improve the reliability of Al₂O₃-DBC substrates under thermal cycling[J]. Microelectronics Reliability, 2015, 56(6): 101-108.
[41] 胡震. 功率器件的故障诊断及疲劳寿命预测[D]. 天津: 天津理工大学, 2014.
[42] Murdock D A, Torres J E R, Connors J J, et al. Active thermal control of power electronic modules[J]. IEEE Transactions on Industrial Application, 2006, 42(2): 552-558.
[43] 陈民铀, 高兵, 杨帆, 等. 基于电-热-机械应力多物理场的IGBT焊料层健康状态研究[J]. 电工技术学报, 2015, 30(20): 252-260.
Chen Minyou, Gao Bing, Yang Fan, et al.Healthy evaluation on IGBT solder based on electro- thermal-mechanical analysis[J]. Transactions of China Electrotechnical Society, 2015, 30(20): 252-260.
[44] 汪波, 罗毅飞, 张烁, 等. IGBT极限功耗与热失效机理分析[J]. 电工技术学报, 2016, 31(12): 135-141.
Wang Bo, Luo Yifei, Zhang Shuo, et al.Analysis of limiting power dissipation and thermal failure mechanism[J]. Transactions of China Electro- technical Society, 2016, 31(12): 135-141.
[45] Feller L, Hartmann S, Schneider D.Lifetime analysis of solder joints in high power IGBT modules for increasing the reliability for operation at 150 degrees centigrade[J]. Microelectronics Reliability, 2008, 48(8): 1161-1166.
[46] Liu Binli, Liu Dezhi, Tang Yong, et al.The investigation on the lifetime prediction model of IGBT[J]. Power Procedia, 2011, 12(1): 394-402.
[47] Held M, Jacob P, Nicoletti G, et al.Fast power cycling test of IGBT modules in traction appli- cation[C]//IEEE International Conference on Power Electronics and Drive Systems, Singapore, 1997: 1-6.
[48] Özkol E, Brem F, Liu C, et al.Enhanced power cycling performance of IGBT modules with a reinforced emitter contact[J]. Microelectronics Reliability, 2015, 55(6): 912-918.
[49] Ciappa M, Fichtner W.Lifetime prediction of IGBT modules for traction applications[C]//38th Annual IEEE International Conference on Reliability Physics Symposium, San Jose, America, 2000: 210-216.
[50] Xiong Yali, Cheng Xu, Shen Z J, et al.Prognostic and warning system for power-electronic modules in electric, hybrid electric, and fuel-cell vehicles[J]. IEEE Transactions on Industrial Electronics, 2008, 55(6): 2268-2276.
[51] 唐勇, 汪波, 陈明, 等. 高温下的IGBT可靠性与在线评估[J]. 电工技术学报, 2014, 29(6): 17-23.
Tang Yong, Wang Bo, Chen Ming, et al.Reliability and on-line evaluation of IGBT modules under high temperature[J]. Transactions of China Electro- technical Society, 2014, 29(6): 17-23.
[52] Lai Wei, Chen Minyou, Ran Li, et al.Experimental investigation on the effects of narrow junction temperature cycles on die-attach solder layer in an IGBT module[J]. IEEE Transactions on Power Electronics, 2017, 32(2): 1431-1441.