|
|
|
| Improved Three-Vector Model Predictive Torque Control of Permanent Magnet Synchronous Motor |
| Chen Wei1, Zeng Sike1, Zhang Guozheng2, Zhou Zhanqing2 |
1. School of Electrical and Information Engineering Tianjin University Tianjin 300072 China;
2. Tianjin Engineering Center of Electric Machine System Design and Control Tianjin Polytechnic University Tianjin 300387 China |
|
|
|
|
Abstract Duty cycle model predicted torque control uses a active vector and a zero vector in a control period to control the permanent magnet synchronous motor. The traditional duty cycle control strategies only focuses on the improvement of torque performance and ignores the suppression of flux ripple reduction, which will causes the flux of the motor to fluctuate greatly and will result in deterioration of the motor's current performance and torque performance. Therefore, this paper proposes an improved three-vector model torque predictive control strategy that suppresses flux fluctuations. By establishing an effective vector selection table, it can flexibly add an additional active vector based on the classical duty cycle model predictive torque control and the duty cycle of each vector is obtained with a small amount of calculation, this paper aim to optimize the control performance of the flux and the torque of the permanent magnet synchronous motor system. The feasibility and effectiveness of proposed strategy are verified by the experimental results on a 6kW PMSM.
|
|
Received: 01 July 2018
Published: 15 February 2019
|
|
|
|
|
|
[1] 陈炜, 赵迎迎, 周湛清, 等. 采用新型评价表的三电平逆变器占空比调制直接转矩控制[J]. 电工技术学报, 2016, 31(增刊1): 128-136.
Chen Wei, Zhao Yingying, Zhou Zhanqing.Direct torque control using new evaluation table of three- level inverter based on duty cycle modulation[J]. Transactions of China Electrotechnical Society, 2016, 31(S1): 128-136.
[2] Zhou Zhanqing, Xia Changliang, Yan Yan, et al.Torque ripple minimization of predictive torque control for PMSM with extended control set[J]. IEEE Transactions on Industrial Electronics, 2017, 64(9): 6930-6939.
[3] Rodriguez J, Cortes P, Kennel R, et al.Model predictive control—a simple and powerful method to control power converters[J]. IEEE Transactions on Industrial Electronics, 2009, 56(6): 1826-1838.
[4] Rodriguez J, Kazmierkowski M P, Espinoza J R, et al.State of the art of finite control set model predictive control in power electronics[J]. IEEE Transactions on Industrial Informatics, 2013, 9(2): 1003-1016.
[5] Davari S A, Khaburi D A, Kennel R.An improved FCS-MPC algorithm for an induction motor with an imposed optimized weighting factor[J]. IEEE Transa- ctions on Power Electronics, 2012, 27(3): 1540-1551.
[6] Zhang Yongchang, Yang Haitao.Model predictive control of induction motor drives: flux control versus torque control[J]. IEEE Transactions on Industrial Applications, 2016, 52(5): 4050-4060.
[7] Zhang Yongchang, Yang Haitao.Model predictive torque control of induction motor drives with optimal duty cycle control[J]. IEEE Transactions on Power Electronics, 2014, 29(12): 6593-6603.
[8] Zhang Yongchang, Yang Haitao.Generalized two- vector-based model-predictive torque control of induction motor drives[J]. IEEE Transactions on Power Electronics, 2015, 30(7): 3818-3829.
[9] Zhang Yongchang, Zhu Jianguo.A novel duty cycle control strategy to reduce both torque and flux ripples for DTC of permanent magnet synchronous motor drives with switching frequency reduction[J]. IEEE Transactions on Power Electronics, 2011, 26(10): 3055-3067. |
|
|
|
2018, Vol. 33 
