Abstract Power electronic and electrical equipment are widely used in industrial fields. Since conducted noise can spread to other devices in the system by equipment terminal, conducted noise suppression method of equipment is crucial for overall system reliability. In this paper, suppression methods of power electronic and electric equipment conducted noise are analyzed systematically. Working principle, implementation and research status are concluded for suppression method from the aspects of filter technique, topology optimization of main circuit and control strategy optimization. Potential research directions and crucial questions of suppression method are addressed, offering reference for further development and application.
Zhang Yicheng,Ye Shangbin,Zhang Jiajia等. Review of Conducted Noise Suppression Method for Power Electronic and Electrical Equipment[J]. Transactions of China Electrotechnical Society, 2017, 32(14): 77-86.
[1] 周国华, 许建平. 开关变换器调制与控制技术综述[J]. 中国电机工程学报, 2014, 34(6): 815-831. Zhou Guohua, Xu Jianping. A review of modulation and control techniques for switching converters[J]. Proceedings of the CSEE, 2014, 34(6): 815-831. [2] Krishna M, Ramesh O. Conducted EMI mitigation techniques for switch-mode power converters: a survey[J]. IEEE Transactions on Power Electronics, 2010, 25(9): 2344-2356. [3] Vuttipon T, Kye Y S, Flavio G, et al. Systematic electromagnetic interference filter design based on information from in-circuit impedance measure- ments[J]. IEEE Transactions on Electromagnetic Compatibility, 2010, 52(3): 588-598. [4] 石磊磊, 王世山, 徐晨琛. 二端口网络散射参数理论及其在平面EMI滤波器测试中的应用[J]. 电工技术学报, 2013, 28(2): 78-85. Shi Leilei, Wang Shishan, Xu Chenchen. Theory of scatter parameters of two port network and its appli- cation in the test of planar EMI filter[J]. Transactions of China Electrotechnical Society, 2013, 28(2): 78-85. [5] Mohit K, Vivek A. Power line filter design for conducted electromagnetic interference using time- domain measurements[J]. IEEE Transactions on Elec- tromagnetic compatibility, 2006, 48(1): 178-186. [6] Sebastian S, Andreas L. EMC behavior of the internal supply of industrial power converters[C]//IEEE Energy Conversion Congress and Exposition, Atlanta, 2010: 2272-2277. [7] Cochrane D, Chen D Y, Boroyevic D. Passive cancellation of common-mode noise in power electronics circuits[J]. IEEE Transactions on Power Electronics, 2003, 18(3): 756-763. [8] Zumel P, Garcia O, Oliver A, et al. Differential-mode EMI reduction in a multiphase DCM flyback con- verter[J]. IEEE Transactions on Power Electronics, 2009, 24(8): 2013-2020. [9] Spiazzi G, Buso S, Citron M, et al. Performance evaluation of a Schottky SiC power diode in a Boost PFC application[J]. IEEE Transactions on Power Electronics, 2003, 18(6): 1249-1253. [10] Rixin L, Yoann M, Fred W, et al. An integrated EMI choke for differential-mode and common-mode noise suppression[J]. IEEE Transactions on Power Elec- tronics, 2010, 25(3): 539-544. [11] Mihali F, Kos D. Reduced conductive EMI in switched-mode DC-DC power converters without EMI filters: PWM versus randomized PWM[J]. IEEE Transactions on Power Electronics, 2006, 21(6): 1783-1794. [12] Chen W, Yang X, Wang Z. An active EMI filtering technique for improving passive filter low-frequency performance[J]. IEEE Transactions on Electro- magnetic Compatibility, 2006, 48(1): 172-177. [13] Biela J, Wirthmueller A, Waespe R, et al. Passive and active Hybrid integrated EMI filter[J]. IEEE Transa- ctions on Power Electronics, 2009, 24(5): 1340-1349. [14] Chen P, Lai Y. Effective EMI filter design method for three-phase inverter based upon software noise separation[J]. IEEE Transactions on Power Elec- tronics, 2010, 25(11): 2797-2806. [15] Vuttipon T. EMI filter design part Ⅲ: selection of filter topology for optimal performance[J]. IEEE Electromagnetic Compatibility Magazine, 2012, 1(2): 60-73. [16] 张佳佳, 张逸成, 韦莉, 等. 基于插入损耗的噪声源阻抗修正计算方法[J]. 电工技术学报, 2015, 30(4): 80-87.
2017, Vol. 32 
