边缘阶梯等效的无轭模块化轴向磁通永磁电机通用三维磁网络模型

doi:10.19595/j.cnki.1000-6753.tces.250074

Abstract
Figure/Table
References
Related Citation (7)

Download: PDF (10574 KB) HTML (1 KB)
Export: BibTeX | EndNote (RIS)

Abstract Due to the advantages of high power density, short end windings, and compact structure, the yokeless and segmented armature (YASA) axial flux permanent magnet motor has become an essential choice for high-performance drive systems such as electric vehicles and aerospace. The equivalent magnetic network (EMN) method considers core saturation and offers a fast calculation speed for determining the magnetic field of an axial flux motor. However, the traditional EMN method cannot accurately estimate the three-dimensional (3D) flux distribution characteristics or fully consider the actual topology of the motor, resulting in an insufficiently accurate initial design scheme. Therefore, this paper proposes a general 3-D EMN model based on edge step equivalent, which provides a fast and precise calculation tool for the initial design of the YASA motor.
Firstly, the topology of the stator and rotor structures of the YASA motor is introduced, and the edge-step equivalent EMN modeling method is proposed. This method transforms the complex topology structure into a regular cube network unit by approximately mapping the motor's curved surface to a plane through an equivalent edge step. Thus, the computational complexity caused by the curved surface network unit can be avoided. The YASA motor is divided into the rotor, sliding (including the air gap and the stator tooth top), and stator areas. The 3-D EMN model is established. The sliding area utilizes a hybrid medium network unit to address the dynamic connection issue between the stator and rotor nodes. Secondly, taking a 20-pole 24-slot YASA motor as an example, the traditional model, the edge step equivalent model, and the finite element method (FEM) are compared in terms of air gap flux density, stator tooth flux density, back electromotive force (EMF), and electromagnetic torque. Finally, a YASA motor is manufactured, and its effectiveness is verified through experiments.
Compared to the traditional EMN, the edge step equivalent EMN can accurately calculate the 3D magnetic flux distribution and consider the core saturation effect. The relative error of the no-load and load air gap flux density of the edge step equivalent EMN is 2.9% and 3.4%, respectively, significantly lower than those of the traditional EMN. The effective value of the back EMF, measured by the no-load experiment at the rated speed, is 135.62 V, while that calculated by the edge step equivalent EMN model is 136.89 V. Under the rated load condition, the torque calculated by the model is 502.24 N·m, while the measured torque is 478 N·m, resulting in an error of approximately 5.07%.
The following conclusions can be drawn. (1) Edge step equivalent EMN obtains a unified network unit, avoids the integral operation, and improves the calculation efficiency. Compared with the traditional EMN model, the calculation speed is improved by 19.1%. (2) The proposed general edge step equivalent EMN model of the YASA motor not only considers the saturation, but also considers the 3-D distribution characteristics of the magnetic flux. The back EMF and torque calculated based on this model are similar to the experimental results, and the calculation accuracy is better than that of the traditional EMN model. (3) The modeling method is universal and can be further extended to other axial flux motors.

Key words： Yokeless and segmented armature axial flux permanent magnet motor edge step equivalent model 3D magnetic circuit

Received: 11 January 2025

PACS:

TM351

	Service

	E-mail this article
	Add to my bookshelf
	Add to citation manager
	E-mail Alert
	RSS
	Articles by authors
	Jiang Shangxuan
	Peng Bing

Cite this article:

Jiang Shangxuan,Peng Bing. Development of Universal 3D Equivalent Magnetic Network Model for Yokeless and Segmented Armature Axial Flux Permanent Magnet Motor Using Edge Step Equivalent Method[J]. Transactions of China Electrotechnical Society, 2026, 41(2): 416-425.

URL:

https://dgjsxb.ces-transaction.com/EN/10.19595/j.cnki.1000-6753.tces.250074 OR https://dgjsxb.ces-transaction.com/EN/Y2026/V41/I2/416

[1] 李涛, 张幽彤, 梁玉秀, 等. 定子无磁轭模块化轴向磁通永磁电机研究进展综述[J]. 中国电机工程学报, 2021, 41(1): 340-353, 423.
Li Tao, Zhang Youtong, Liang Yuxiu, et al.An over- view on research progress of yokeless and segmented armature axial flux permanent magnet machine[J]. Proceedings of the CSEE, 2021, 41(1): 340-353, 423.
[2] 高鹏, 任红兴, 王晓远, 等. 磁极径向组合式定子无磁轭模块化轴向磁通电机磁热特性分析[J]. 电工技术学报, 2025, 40(24): 7969-7983.
Gao Peng, Ren Hongxing, Wang Xiaoyuan, et al.Magnetic and thermal characteristics analysis of mag- netic pole radial combination yokeless and segmented armature axial flux machine[J]. Transactions of China Electrotechnical Society, 2025, 40(24): 7969-7983.
[3] 关涛, 刘大猛, 何永勇. 永磁轮毂电机技术发展综述[J]. 电工技术学报, 2024, 39(2): 378-396.
Guan Tao, Liu Dameng, He Yongyong.Review on development of permanent magnet in-wheel motors[J]. Transactions of China Electrotechnical Society, 2024, 39(2): 378-396.
[4] Geng Weiwei, Hou Jining, Li Qiang.Electromagnetic analysis and efficiency improvement of axial-flux permanent magnet motor with yokeless stator by using grain-oriented silicon steel[J]. IEEE Transa- ctions on Magnetics, 2022, 58(2): 8200905.
[5] 佟文明, 杜绍雨, 贾建国, 等. 基于改进复相对磁导函数的开槽轴向磁通永磁电机气隙磁场解析模型[J]. 电工技术学报, 2024, 39(24): 7700-7711.
Tong Wenming, Du Shaoyu, Jia Jianguo, et al.Analytical model of air-gap magnetic field of slotted axial flux permanent magnet motor based on improved complex relative permeance function[J]. Transactions of China Electrotechnical Society, 2024, 39(24): 7700-7711.
[6] Tak B O, Ro J.Analysis and design of an axial flux permanent magnet motor for in-wheel system using a novel analytical method combined with a numerical method[J]. IEEE Access, 2020, 8: 203994-204011.
[7] Hemeida A, Lehikoinen A, Rasilo P, et al.A simple and efficient quasi-3D magnetic equivalent circuit for surface axial flux permanent magnet synchronous machines[J]. IEEE Transactions on Industrial Elec- tronics, 2019, 66(11): 8318-8333.
[8] Jia Lun, Lin Mingyao, Lin Keman, et al.Design and analysis of axial-flux modular spoke-type permanent magnet machines with segmented stators for traction applications[J]. IEEE Transactions on Transportation Electrification, 2024, 10(2): 4290-4301.
[9] Sun Xining, Wang Limei, Fan Xinggang, et al.A quasi-three-dimensional magnetic equivalent circuit model of yokeless and segmented armature axial flux motors considering radial segmentation magnetic coupling[C]//2022 IEEE Transportation Electrifi- cation Conference and Expo, Asia-Pacific (ITEC Asia-Pacific), Haining, China, 2022: 1-6.
[10] Li Nian, Zhu Jianguo, Lin Mingyao, et al.Analysis of axial field flux-switching memory machine based on 3-D magnetic equivalent circuit network considering magnetic hysteresis[J]. IEEE Transactions on Mag- netics, 2019, 55(6): 7203104.
[11] Hou Jining, Geng Weiwei, Li Qiang, et al.3-D equivalent magnetic network modeling and FEA verification of a novel axial-flux hybrid-excitation in-wheel motor[J]. IEEE Transactions on Magnetics, 2021, 57(7): 8106912.
[12] 王超, 彭兵, 闫伟, 等. YASA轴向磁通永磁电机定子槽漏感计算[J]. 中国电机工程学报, 2024, 44(10): 4082-4091.
Wang Chao, Peng Bing, Yan Wei, et al.Calculation of slot inductance of axial flux permanent machine with yokeless and segmented armature[J]. Pro- ceedings of the CSEE, 2024, 44(10): 4082-4091.
[13] Li Guidan, Dong Zun, Li Bin, et al.An improved equivalent magnetic network model of modular IPM machines[J]. IEEE Transactions on Magnetics, 2022, 58(4): 8104609.
[14] Liu Guohai, Wang Yong, Chen Qian, et al.Design and analysis of a new equivalent magnetic network model for IPM machines[J]. IEEE Transactions on Magnetics, 2020, 56(6): 8101112.
[15] 朱旭光, 刘正蒙, 刘国海, 等. 基于混合介质网格的表贴式永磁游标电机通用等效磁网络模型[J]. 中国电机工程学报, 2024, 44(5): 2009-2019.
Zhu Xuguang, Liu Zhengmeng, Liu Guohai, et al.General equivalent magnetic network model of surface permanent magnet vernier machine based on hybrid medium mesh[J]. Proceedings of the CSEE, 2024, 44(5): 2009-2019.
[16] Huang Yunkai, Zhou Tao, Dong Jianning, et al.Magnetic equivalent circuit modeling of yokeless axial flux permanent magnet machine with segmented armature[J]. IEEE Transactions on Magnetics, 2014, 50(11): 8104204.
[17] Ghods M, Faiz J, Bazrafshan M A, et al.A mesh design technique for double stator linear PM vernier machine based on equivalent magnetic network modeling[J]. IEEE Transactions on Energy Con- version, 2022, 37(2): 1087-1095.
[18] 佟文明, 王萍, 吴胜男, 等. 基于三维等效磁网络模型的混合励磁同步电机电磁特性分析[J]. 电工技术学报, 2023, 38(3): 692-702.
Tong Wenming, Wang Ping, Wu Shengnan, et al.Electromagnetic performance analysis of a hybrid excitation synchronous machine based on 3D equi- valent magnetic network[J]. Transactions of China Electrotechnical Society, 2023, 38(3): 692-702.
[19] Seyedi S M, Sharifi A H, Mohammadi A A.Com- putation of armature reaction field and full-load characteristics of an axial flux surface mounted PM machine using a new analytical approach[C]//Iranian Conference on Electrical Engineering (ICEE), Mashhad, Iran, 2018: 1027-1031.
[20] 黄允凯, 周涛. 基于等效磁路法的轴向永磁电机效率优化设计[J]. 电工技术学报, 2015, 30(2): 73-79.
Huang Yunkai, Zhou Tao.Efficiency optimization design of axial flux permanent magnet machines using magnetic equivalent circuit[J]. Transactions of China Electrotechnical Society, 2015, 30(2): 73-79.
[21] 佟文明, 姚颖聪, 李世奇, 等. 考虑磁桥不均匀饱和的内置式永磁同步电机等效磁网络模型[J]. 电工技术学报, 2022, 37(12): 2961-2970.
Tong Wenming, Yao Yingcong, Li Shiqi, et al.Equivalent magnetic network model for interior permanent magnet machines considering non-uniform saturation of magnetic bridges[J]. Transactions of China Electrotechnical Society, 2022, 37(12): 2961-2970.
[22] 吴胜男, 庞先文, 佟文明, 等. 模块化定子混合励磁同步电机磁网络建模与分析[J]. 电机与控制学报, 2023, 27(12): 95-104.
Wu Shengnan, Pang Xianwen, Tong Wenming, et al.Modeling and analysis of magnetic network of modular stator hybrid excitation synchronous motors[J]. Elec- tric Machines and Control, 2023, 27(12): 95-104.