永磁游标电机多自由度磁场调制器设计

doi:10.19595/j.cnki.1000-6753.tces.250407

Abstract
Figure/Table
References
Related Citation (15)

Download: PDF (10437 KB) HTML (1 KB)
Export: BibTeX | EndNote (RIS)

Abstract The permanent magnet vernier machine (PMVM) is popular for its simple structure and high torque density. It can be modeled as three modules: the PM unit as the excitation source, the tooth-slot structure as the modulator, and the armature winding as the filter. The excitation source generates a magnetic electromotive force, and the modulator converts it into multiple magnetic field harmonics. The winding filter then extracts some of these harmonics to generate back electromotive force. The modulator design is crucial as it determines the magnetic field modulation capability and impacts the output torque. Traditional modulator designs with fixed tooth shapes and limited parameters cannot fully optimize permeance harmonics, limiting torque. Therefore, this paper proposes a multi-degree-of-freedom modulator design method to maximize torque.
First, the stator is divided into Region Ⅰ and Region Ⅱ. Region Ⅰ is the part of the tooth slot structure near the stator yoke, which does not directly affect the distribution of airgap permeance. Region Ⅱ is the part of the tooth slot structure adjacent to the airgap, directly affecting the distribution of airgap permeance. Therefore, Region Ⅱ is the key to the design of stator magnetic field modulators. Then, decompose the stator slot into 3 modulation factors and the stator teeth into 15 modulation factors, which can be freely combined to form different modulator structures.
Then, the PMVM with different modulation ratios is designed. Although increasing the modulation ratio can enhance magnetic field modulation performance and torque, a higher number of rotor poles increases flux leakage. There is a trade-off between the maximum output torque and the optimal magnetic field modulation ratio. The modulation ratio should be carefully selected.
In addition, to further improve optimization efficiency, a modulation tooth structure with continuous modulation factors replaces the original discrete tooth structure. A continuous equivalent split tooth is formed by combining trapezoidal and triangular shapes. The bottom width of the trapezoid is controlled by angles Angle₁ and Angle₂, while the top width and height of the trapezoid are controlled by angles Angle_{1_1}, Angle_{2_1}, and y₁, which also form the bottom of the triangle. The triangle's height is controlled by y₂. This approach reduces the original 15 modulation factors to 6, enhancing optimization efficiency. The torques of equivalent split teeth and multi-degree-of-freedom split teeth are almost identical. The slight difference is due to the continuous variation of the split modulation factor of the equivalent split tooth. The multi-degree-of-freedom split modulation factor exhibits discrete variation, whereas the continuous height variation is continuous. Therefore, the equivalent split-tooth structure is more suitable for the design of multi-degree-of-freedom modulators and for applications across a broader range of slot-topology groups.
Finally, a 12s34p PMVM is designed using the proposed equivalent teeth. Compared with the conventional uniform split-tooth PMVM, its torque has increased by 37.53%. The prototype has been manufactured, and the experimental results are highly consistent with expectations. This method proposes a new approach to improving torque in PMVM.

Key words： Permanent magnet vernier machine magnetic field modulator design working harmonics multi degree of freedom design torque

Received: 17 March 2025

PACS:

TM351

	Service

	E-mail this article
	Add to my bookshelf
	Add to citation manager
	E-mail Alert
	RSS
	Articles by authors
	Wang Rongxin
	Wang Bo
	Cai Haiwei
	Zhao Wenjun
	Cheng Ming

Cite this article:

Wang Rongxin,Wang Bo,Cai Haiwei等. Design of Multi Degree of Freedom Magnetic Field Modulator for Permanent Magnet Vernier Machine[J]. Transactions of China Electrotechnical Society, 2026, 41(4): 1169-1180.

URL:

https://dgjsxb.ces-transaction.com/EN/10.19595/j.cnki.1000-6753.tces.250407 OR https://dgjsxb.ces-transaction.com/EN/Y2026/V41/I4/1169

[1] Xu Liang, Li Yang, Zhao Wenxiang, et al.Reduction of unipolar leakage flux and torque ripple in consequent-pole PM vernier machine[J]. CES Transa- ctions on Electrical Machines and Systems, 2023, 7(1): 35-44.
[2] 林宝全, 李捷, 杨公德. 永磁游标电机转矩特性研究[J]. 电气工程学报, 2023, 18(4): 35-42.
Lin Baoquan, Li Jie, Yang Gongde.Research of torque characteristics of permanent magnet vernier machine[J]. Journal of Electrical Engineering, 2023, 18(4): 35-42.
[3] Zhou Huawei, Tao Weiguo, Chen Cheng, et al.Analysis and comparison of even-order back EMF harmonics of fractional-slot concentrated-winding consequent pole permanent magnet vernier machines[J]. IEEE Transactions on Transportation Electrification, 2023, 10(1): 1969-1981.
[4] 樊英, 陈秋蒴, 陈俊磊, 等. 基于无人配送车辆运行工况的交替极游标轮毂电机优化设计[J]. 电工技术学报, 2023, 38(19): 5141-5151.
Fan Ying, Chen Qiushuo, Chen Junlei, et al.Opti- mization design of consequent pole vernier wheel motor based on operating conditions of unmanned delivery vehicles[J]. Transactions of China Electro- technical Society, 2023, 38(19): 5141-5151.
[5] 周健荣, 樊德阳, 项子旋, 等. V型游标永磁电机功率因数内在机理及其提升方法[J]. 电工技术学报, 2023, 38(14): 3789-3799.
Zhou Jianrong, Fan Deyang, Xiang Zixuan, et al.Production mechanism of power factor of V-type vernier permanent magnet machine and improvement method[J]. Transactions of China Electrotechnical Society, 2023, 38(14): 3789-3799.
[6] Zhu Yan, Liu Guohai, Xu Liang, et al.A hybrid analytical model for permanent magnet vernier machines considering saturation effect[J]. IEEE Transactions on Industrial Electronics, 2021, 69(2): 1211-1223.
[7] 程明, 文宏辉, 花为, 等. 电机气隙磁场调制统一理论及其典型应用[J]. 中国电机工程学报, 2021, 41(24): 8261-8283.
Cheng Ming, Wen Honghui, Hua Wei, et al.General airgap field modulation theory for electrical machines and its typical applications[J]. Proceedings of the CSEE, 2021, 41(24): 8261-8283.
[8] 李亚, 周庆林, 丁石川, 等. 表嵌式交替极永磁电机拓扑演化及气隙磁场调制效应研究[J]. 电工技术学报, 2023, 38(12): 3188-3198.
Li Ya, Zhou Qinglin, Ding Shichuan, et al.Investi- gation of topologies evolution and air-gap field modulation effect on surface-inset consequent-pole PM machines[J]. Transactions of China Electrotech- nical Society, 2023, 38(12): 3188-3198.
[9] 文宏辉. 电机气隙磁场调制统一理论及应用方法研究[D]. 南京: 东南大学, 2021.
Wen Honghui.Research on the general airgap field modulation theory for electrical machines and its application methods[D]. Nanjing: Southeast University, 2021.
[10] Ishizaki A, Tanaka T, Takasaki K, et al.Theory and optimum design of PM vernier motor[C]//1995 Seventh International Conference on Electrical Machines and Drives, Durham, UK, 1995: 208-212.
[11] He Zhuofan, Xiao Feng, Du Yi, et al.Comparison of permanent magnet vernier motors with evenly and unevenly distributed modulation teeth[J]. IEEE Transactions on Magnetics, 2023, 59(11): 8203005.
[12] Fang Li, Li Dawei, Ren Xiang, et al.A quantitative air-gap construction method to maximize torque of vernier PM machines[J]. IEEE Transactions on Transportation Electrification, 2023, 9(1): 463-473.
[13] 王秀平, 姜胜龙, 曲春雨. 新型Halbach阵列永磁游标电机结构优化设计[J]. 电机与控制学报, 2023, 27(4): 140-147.
Wang Xiuping, Jiang Shenglong, Qu Chunyu.Structural optimization design of Halbach array permanent magnet cursor motor[J]. Electric Machines and Control, 2023, 27(4): 140-147.
[14] Yu Yanlei, Pei Yulong, Chai Feng.Power factor analysis in spoke-type permanent magnet vernier motors with different slot-pole combinations for in-wheel direct drive[J]. IEEE Transactions on Transportation Electrification, 2023, 9(1): 642-655.
[15] 鲍晓华, 刘佶炜, 孙跃, 等. 低速大转矩永磁直驱电机研究综述与展望[J]. 电工技术学报, 2019, 34(6): 1148-1160.
Bao Xiaohua, Liu Jiwei, Sun Yue, et al.Review and prospect of low-speed high-torque permanent magnet machines[J]. Transactions of China Electrotechnical Society, 2019, 34(6): 1148-1160.
[16] Li Huayang, Zhu Z Q, Liu Yue.Optimal number of flux modulation pole in vernier permanent magnet synchronous machines[J]. IEEE Transactions on Industry Applications, 2019, 55(6): 5747-5757.
[17] Yu Yanlei, Chai Feng, Pei Yulong, et al.Comparisons of torque performance in surface-mounted PM vernier machines with different stator tooth topologies[J]. IEEE Transactions on Industry Applications, 2019, 55(4): 3671-3684.
[18] 徐亮. 磁场调制式永磁容错电机的分析、设计与控制[D]. 镇江: 江苏大学, 2017.
Xu Liang.Analysis, design and control of flux- modulation permanent-magnet fault-tolerant motor[D]. Zhenjiang: Jiangsu University, 2017.
[19] Fang Li, Li Dawei, Ren Xiang, et al.A novel permanent magnet vernier machine with coding- shaped tooth[J]. IEEE Transactions on Industrial Electronics, 2022, 69(6): 6058-6068.
[20] 程明, 马钲洲, 花为, 等. 电机气隙磁场调制统一理论研究进展与展望[J]. 中国电机工程学报, 2025, 45(4): 1220-1237.
Cheng Ming, Ma Zhengzhou, Hua Wei, et al.Research progresses and prospects of general airgap field modulation theory for electrical machines[J]. Proceedings of the CSEE, 2025, 45(4): 1220-1237.
[21] Jiang Tingting, Zhao Wenxiang, Xu Liang.Analysis of split-tooth stator PM vernier machines with zero- sequence current excitation[J]. IEEE Transactions on Industrial Electronics, 2023, 70(2): 1229-1238.
[22] 贾宛英, 花玉梦, 王明杰, 等. 新型电励磁双凸极电机转子极数对电机性能影响[J]. 电工技术学报, 2025, 40(8): 2418-2429.
Jia Wanying, Hua Yumeng, Wang Mingjie, et al.Influence of rotor pole number on motor performance in novel doubly salient motor[J]. Transactions of China Electrotechnical Society, 2025, 40(8): 2418-2429.
[23] 项子旋, 卢子润, 朱孝勇, 等. 轮辐式永磁轮毂电机高效轻质设计与优化研究[J]. 中国电机工程学报, 2021, 41(24): 8283-8295.
Xiang Zixuan, Lu Zirun, Zhu Xiaoyong, et al.High- efficiency and lightweight design and optimization of spoke-type permanent magnet in-wheel motor[J]. Proceedings of the CSEE, 2021, 41(24): 8283-8295.
[24] Du Kangkang, Xu Liang, Zhao Wenxiang, et al.Analysis and design of a fault-tolerant permanent magnet vernier machine with improved power factor[J]. IEEE Transactions on Industrial Electronics, 2022, 69(5): 4353-4363.
[25] Wu Zhaopeng, Quan Li, Xiang Zixuan, et al.Airgap- harmonic-oriented partitioned design method of PMV motor with improved torque performances[J]. CES Transactions on Electrical Machines and Systems, 2024, 8(1): 43-50.
[26] 陈威, 吴桂初, 方攸同. 基于绕组分布函数理论和动态磁网络的两种内置式永磁牵引电机解析建模方法[J]. 电工技术学报, 2020, 35(增刊2): 377-386.
Chen Wei, Wu Guichu, Fang Youtong.Two analytical models based on winding function theory and dynamic reluctance mesh for interior permanent magnet traction machines[J]. Transactions of China Electrotechnical Society, 2020, 35(S2): 377-386.
[27] 王柄东, 王道涵, 王晓姬, 等. 交流调磁型永磁同步电机磁通协同调控最大转矩铜耗比控制[J]. 电工技术学报, 2024, 39(12): 3630-3645.
Wang Bingdong, Wang Daohan, Wang Xiaoji, et al.A maximum torque per copper loss control for AC flux-regulation permanent magnet synchronous motor with magnetic flux co-regulation[J]. Transactions of China Electrotechnical Society, 2024, 39(12): 3630-3645.