Non-Matching Meshes Mapping Method in Coupled Magnetic and Thermal Analysis of Electromagnetic Devices
Zhang Yujiao1,2, Qin Weinan3, Liu Dongyuan1 ,Wu Gangliang1
1.College of Electrical Engineering and New Energy China Three Gorges University Yichang 443002 China; 2.State Key Lab.of Power System Tsinghua University Beijing 100084 China; 3.State Grid Jinhua Power Supply Company Jinhua 321001 China
Abstract：In the coupled electromagnetic fluid-dynamical and thermal simulations which are done by the weak coupling finite element method (FEM) for the electromagnetic devices,the thermal loads obtained from the energy losses by electromagnetic calculations are transferred between meshes to calculate the temperature distributions by considering the influence of air and fluid flow.Because the requirements of the meshes discretization scheme are quite different between electromagnetic and fluid-thermal fields,the same finite element model applied to analyze both requirements will lead to increase the number of meshes and the time of calculation.However,if different finite element models are used,the data cannot be directly transferred between the corresponding meshes.In this paper,a non-matching mesh mapping method is proposed.The energy losses can be transferred between the different meshes by the Gauss integral and coordinate transformation.Moreover,the strategy of precision control and error correction coefficient are proposed to ensure the calculation accuracy.This method is applied to an air insulation bus duct system in the literature.The calculation results are compared with the normal matching meshes mapping method and the experiment results to validate the proposed non-matching meshes mapping method.
张宇娇,秦威南,刘东圆,吴刚梁. 面向电磁装置磁-热耦合分析的异型网格映射方法[J]. 电工技术学报, 2016, 31(13): 141-148.
Zhang Yujiao, Qin Weinan, Liu Dongyuan ,Wu Gangliang. Non-Matching Meshes Mapping Method in Coupled Magnetic and Thermal Analysis of Electromagnetic Devices. Transactions of China Electrotechnical Society, 2016, 31(13): 141-148.
[1] 陈益广,郑军,魏娟,等.舵机用永磁同步电机的设计与温度场分析[J].电工技术学报,2015,30(14):94-99. Chen Yiguang,Zheng Jun,Wei Juan,et al.Design of PMSM for actuator and its temperature field analysis[J].Transactions of China Electrotechnical Society,2015,30(14):94-99. [2] 陈民铀,高兵,杨帆,等.基于电-热-机械应力多物理场的IGBT 焊料层健康状态研究[J].电工技术学报,2015,30(20):252-260. Chen Minyou,Gao Bing,Yang Fan,et al.Healthy evaluation on IGBT solder based on electro-thermal-mechanical analysis[J].Transactions of China Electrotechnical Society,2015,30(20):252-260. [3] 黄文美,薛胤龙,王莉,等.考虑动态损耗的超磁致伸缩换能器的多场耦合模型[J].电工技术学报,2016,31(7):173-178. Huang Wenmei,Xue Yinlong,Wang Li,et al.Multi-field coupling model considering dynamic losses for giant magnetostrictive transducers[J].Transactions of China Electrotechnical Society,2016,31(7):173-178. [4] 杜海,曲延滨,张鹏.新型旋转电磁热机流体流动与传热的耦合计算与实验[J].电工技术学报,2015,30(12):291-297. Du Hai,Qu Yanbin,Zhang Peng.Coupling calculation and experiment of fluid flow and heat transfer of a new rotating induction heater[J].Transactions of China Electrotechnical Society,2015,30(12):291-297. [5] 段涛,杨斌,李贤庆,等.±500 kV换流站阀水冷系统隐患分析治理[J].电力系统保护与控制,2014,42(18):132-138. Duan Tao,Yang Bin,Li Xianqing,et al.Analysis of potential dangers in ±500 kV converter station valve water cooling system[J].Power System Protection and Control,2014,42(18):132-138. [6] 周封,熊斌,李伟力,等.大型电机定子三维流体场计算及其对温度场分布的影响[J].中国电机工程学报,2005,25(24):128-132. Zhou Feng,Xiong Bin,Li Weili,et al,Numerical calculation of 3D stator fluid for large electrical machine as well as influences on thermal field distribution[J].Proceedings of the CSEE,2005,25(24):128-132. [7] 王彬,杨庆山.弱耦合算法的实现及其应用[J].工程力学,2008,25(12):48-53. Wang Bin,Yang Qingshan.Realization and application of loosely coupled algorithm[J].Engineering Mechanics,2008,25(12):48-53. [8] Alberti L,Bianchi N.A coupled thermal-electromagnetic analysis for a rapid and accurate prediction of IM performance[J].IEEE Transactions on Industrial Electronics,2008,55(10):3575-3582. [9] 程志光,高桥则雄,博扎德·弗甘尼.电气工程电磁热场模拟与应用[M].北京:科学出版社,2009. [10]王海军,王宁,杨仕友,等.基于ThermNet和MagNet的水轮发电机端部电磁、温度场仿真研究[J].电工技术学报,2013,28(2):116-121. Wang Haijun,Wang Ning,Yang Shiyou,et al.Numerical calculations of the coupled eddy current-temperature fields in the end regions of large hydro-generator using magnet and thermnet software[J].Transactions of China Electrotechnical Society,2013,28(2):116-121. [11]刘永志,李岩,井永腾.基于Fluent软件的电力变压器温度场计算与分析[J].高压电器,2012,48(10):6-11. Liu Yongzhi,Li Yan,Jing Yongteng.Calculation and analysis of temperature field of power transfer based software fluent[J].High Voltage Apparatus,2012,48(10):6-11. [12]宋帆.800 kV GIS隔离开关磁场-温度场计算与分析[J].高电压技术,2008,34(7):1383-1388. Song Fan.Calculation and analysis on magneto-thermal fields of 800 kV GIS disconnector[J].High Voltage Engineering,2008,34(7):1383-1388. [13]胡田,唐任远,李岩,等.永磁风力发电机三维温度场计算及分析[J].电工技术学报,2013,28(3):122-126. Hu Tian,Tang Renyuan,Li Yan,et al.Thermal analysis and calculation of permanent magnet wind generators[J].Transactions of China Electrotechnical Society,2013,28(3):122-126. [14]武安波,王建华,耿英三.密集型母线槽磁场-温度场综合有限元分析[J].高压电器,2003,39(4):7-10. Wu Anbo,Wang Jianhua,Geng Yingsan.Finite element analysis of coupled magneto-thermal fields for compact busbar trunking system[J].High Voltage Apparatus,2003,39(4):7-10. [15]孙国霞,舒乃秋,吴晓文,等.基于多物理场耦合的气体绝缘母线触头接触温升有限元计算[J].电工技术学报,2013,28(2):408-413. Sun Guoxia,Shu Naiqiu,Wu Xiaowen,et al.Finite element analysis of contact temperature rise in gas insulated busbars based on coupled multi-physics[J].Transations of China Electrotechnical Society,2013,28(2):408-413. [16]付朝阳,刘景林,赵小鹏.双余度永磁无刷直流电机磁-热耦合分析[J].西北工业大学学报,2010,28(6):921-926. Fu Zhaoyang,Liu Jinglin,ZhaoXiaopeng.Magnetic-thermal coupling analysis of dual-redundancy BLDCM[J].Journal of Northwestern Polytechnical University,2010,28(6):921-926. [17]Zhang Yujiao,Ruan Jiangjun,Huang Tao,et al.Calculation of temperature rise in air-cooled induction motors through 3-D coupled electromagnetic fluid-dynamical and thermal finite-element analysis[J].IEEE Transactions on Magnetics,2012,48(2):1047-1050. [18]范镇南,张德威,陈显坡,等.用电磁场和流场模型计算GIS母线损耗发热[J].高电压技术,2008,34(12):3016-3021. Fan Zhennan,Zhang Dewei,Chen Xianpo,et al.Calculation of loss and heat of GIS bus bar using electromagnetic field and fluid field[J].High Voltage Engineering,2008,34(12):3016-3021. [19]关晓存,李治源,赵然,等.线圈炮电枢电磁热耦合仿真分析[J].强激光与粒子束,2011,23(8):2267-2272. Guan Xiaocun,Li Zhiyuan,Zhao Ran,et al.Simulation analysis of electromagnetic-thermal coupling for armature in inductive coilgun[J].High Power Laser and Particle Beams,2011,23(8):2267-2272. [20]李岩,额尔和木巴亚尔,张霄霆,等.变压器磁热耦合计算与局部过热屏蔽措施[J].沈阳工业大学学报,2012,34(4):366-371. Li Yan,Eerhemubayaer,Zhang Xiaoting,et al.Magnetic-thermal coupling calculation and shielding measure of local overheating for ttransformer[J].Journal of Shenyang University of Technology,2012,34(4):366-371. [21]额尔和木巴亚尔,李岩,孙昕.基于Ansoft的变压器磁-热耦合分析[J].变压器,2011,48(3):29-33. Eerhemubayaer,Li Yan,Sun Xin.Magnet-thermal couple analysis of transformer based on ansoft[J].Transformer,2011,48(3):29-33. [22]夏海霞,姚缨英,熊素铭,等.1 000 MW汽轮发电机端部磁-热耦合分析[J].中国电机工程学报,2008,28(14):118-122. Xia Haixia,Yao Yingying,Xiong Suming,et al.Magnetic-thermal coupling analysis of end region of 1 000 MW turbine-generator[J].Proceedings of the CSEE,2008,28(14):118-122. [23]张琪,王伟旭,黄苏融,等.高密度车用永磁电机流固耦合传热仿真分析[J].电机与控制应用,2012,39(8):1-5. Zhang Qi,Wang Weixu,Huang Surong,et al.Heat transfer simulation of high density permanent magnet motor for vehicles based on fluid-solid coupling method[J].Electric Machines & Control Application,2012,39(8):1-5. [24]陈小军.高速永磁无刷直流电机磁热耦合分析与效率优化研究[D].广州:广东工业大学,2013. [25]李青青,黄勤,杨立,等.无刷力矩电动机电磁场-温度场耦合仿真与分析[J].微特电机,2013,41(8):30-39. Li Qingqing,Huang Qin,Yang Li,et al.Coupling analysis and simulation of electromagnetic field and temperature field for brushless torque motor[J].Small and Special Electrical Machines,2013,41(8):30-39. [26]Ansys Workbench 14.0 Help. [27]Wu Anbo,Chen Degui,Wang Jianhua,et al,Evaluation of thermal performance for air-insulated busbar trunking system by coupled magneto-fluid-thermal fields[C]//Proceedings of International Conference on Power System Technology,Kunming,2002,4:2159-2163. [28]甘艳,阮江军,张宇.应用混合有限元法有限体积法处理运动电磁问题[J].电工技术学报,2006,21(11):2-7. Gan Yan,Ruan Jiangjun,Zhang Yu.A hybrid finite element method and finite volume method for the simulation of motion problems[J].Transactions of China Electrotechnical Society,2006,21(11):2-7. [29]倪光正,杨仕友,钱秀英,等.工程电磁场数值计算[M].北京:机械工业出版社,2004. [30]王勖成,邵敏.有限单元法基本原理和数值方法[M].北京:清华大学出版社,1997. [31]周岱,马骏,李磊.流场和流固耦合问题网格剖分与更新的新方法[J].工程力学,2009,26(11):10-16. Zhou Dai,Ma Jun,Li Lei.A novel technique for mesh generation and update in the analysis of flow field and fluid-structure interaction[J].Engineering Mechanics,2009,26(11):10-16. [32]赵镇南.传热学[M].北京:高等教育出版社, 2008. [33]Ho S L,Li Y,Lin X,et al.Calculations of eddy current,fluid,and thermal fields in an air insulated bus duct system[J].IEEE Transactions on Magnetics,2007,43(4):1433-1436. [34]Ho S L,Li Y,Lin X,et al.A 3-D study of eddy current field and temperature rises in a compact bus duct system[J].IEEE Transactions on Magnetics,2006,42(4):987-990. [35]武安波,张国刚.基于磁场-流场-温度场耦合计算的母线槽热性能分析[J].电工电能新技术,2002,21(3):62-66. Wu Anbo,Zhang Guogang.Analysis of thermal capacity for busbar trunking system by coupled magneto-fluid-thermal field calculation[J].Advanced Technology of Electrical Engineering and Energy,2002,21(3):62-66.
2016, Vol. 31 
