滑动电接触梯度电枢材料熔化磨损特性仿真研究

doi:10.19595/j.cnki.1000-6753.tces.231406

Abstract
Figure/Table
References (0)
Related Citation (8)

Download: PDF (1200 KB) HTML (1 KB)
Export: BibTeX | EndNote (RIS)

Abstract

The electromagnetic railgun is a novel kinetic energy weapon concept that utilizes controllable and precise electromagnetic forces generated by electromagnetic devices to propel the armature and ammunition in a linear trajectory. In comparison to traditional powder launch systems, electromagnetic railguns must endure high currents and substantial contact pressures during the launch process. Due to the initially low movement speed of the armature, the Joule heat primarily causes surface melting and wear. This leads to a concentrated deposition of the metal liquefaction layer on the track surface, resulting in significant deterioration of the electrical contact with the guide rail in this section. These demanding working conditions impose stringent requirements on the electromagnetic railgun materials, necessitating high-temperature resistance, high yield strength, and high hardness. Typically, the contact surface between the solid armature and the launch track is prone to melting and wear due to the combined effects of Joule heat and frictional heat. Subsequently, the metal liquefaction layer cools and deposits onto the track surface. After repeated launches, the thickness of the deposited layer on the track surface increases or even detaches, leading to reduced track surface smoothness, alterations in track spacing, and interior contamination. Consequently, the service life and launch controllability of the electromagnetic railgun are compromised.
Gradient materials exhibit continuously changing physical properties along the thickness direction. This characteristic enables them to harness the benefits of various materials while avoiding the risk of cracking and fracturing under high temperature and pressure conditions. This article proposes a method for enhancing the armatures' surface melting point, reducing their melting wear rate, and extending the rails' service life in electromagnetic orbit launchers through the use of gradient material armatures. By employing multi-physical field coupling simulation, suitable gradient material armatures were identified to investigate their melting wear characteristics. Initially, a "flat plate" layered gradient material model was adopted. The mechanical, thermal, and electrical properties of each composite material layer were expressed as functions of the volume fraction of the functional material, using a volume fraction exponential expression. Subsequently, utilizing Comsol Multiphysics, the simulation considered the armature's melting during the initial stage, influenced by Joule heat generated by current flow resistance and contact resistance between the armature and rail surface.
Results indicate that chromium is the most suitable functional material for forming gradient material armatures when combined with an aluminum matrix. It is followed by niobium and molybdenum. On the other hand, copper-based functional gradient material armatures exhibit weaker resistance to melting wear. In the case of armatures composed solely of functional materials, molybdenum and copper-coated armatures demonstrate stronger resistance to melting wear, followed by chromium-coated armatures. Niobium-coated armatures display the weakest resistance to melting wear. The simulation experiment will be applied to the production and testing of gradient material armatures. The simulation outcomes hold significant guiding implications for gradient material armature testing.

Key words： electromagnetic railgun gradient material armature melting wear simulation analysis

Received: 28 August 2023

PACS:

TJ866

	Service

	E-mail this article
	Add to my bookshelf
	Add to citation manager
	E-mail Alert
	RSS
	Articles by authors
	Zou Xinyang
	Chen Lixue
	Wang Zengji
	Xu Xuan
	Zhang Zhiyao

Cite this article:

Zou Xinyang,Chen Lixue,Wang Zengji等. Study on Melting and Wear Characteristics of Sliding Electric Contact Gradient Armature[J]. Transactions of China Electrotechnical Society, 0, (): 231406-231406.

URL:

https://dgjsxb.ces-transaction.com/EN/10.19595/j.cnki.1000-6753.tces.231406 OR https://dgjsxb.ces-transaction.com/EN/Y0/V/I/231406

[1] 张嘉炜, 鲁军勇, 谭赛, 等. 考虑初始接触压力的滑动电接触界面磁扩散模型[J]. 电工技术学报, 2022, 37(2): 488-495.
Zhang Jiawei, Lu Junyong, Tan Sai, et al.A magnetic diffusion model of electromagnetic launcher considering initial contact pressure[J]. Transactions of China Electrotechnical Society, 2022, 37(2): 488-495.
[2] 翟小飞, 李鑫航, 刘华, 等. 电磁轨道发射系统电路模型及发射效率研究[J]. 电工技术学报, 2023, 38(11): 2841-2849, 2860.
Zhai Xiaofei, Li Xinhang, Liu Hua, et al.Research on circuit model and launch efficiency of electromagnetic rail launch system[J]. Transactions of China Electrotechnical Society, 2023, 38(11): 2841-2849, 2860.
[3] 马伟明, 鲁军勇. 电磁发射技术的研究现状与挑战[J]. 电工技术学报, 2023, 38(15): 3943-3959.
Ma Weiming, Lu Junyong.Research progress and challenges of electromagnetic launch technology[J]. Transactions of China Electrotechnical Society, 2023, 38(15): 3943-3959.
[4] 马伟明. 关于电工学科前沿技术发展的若干思考[J]. 电工技术学报, 2021, 36(22): 4627-4636.
Ma Weiming.Thoughts on the development of frontier technology in electrical engineering[J]. Transactions of China Electrotechnical Society, 2021, 36(22): 4627-4636.
[5] 刘贵民, 杨忠须, 闫涛, 等. 电磁轨道炮导轨失效研究现状及展望[J]. 材料导报, 2015, 29(7): 63-70.
Liu Guimin, Yang Zhongxu, Yan Tao, et al.Current status and prospect on rail failures of electromagnetic railgun[J]. Materials Review, 2015, 29(7): 63-70.
[6] (美)理查德·埃斯特里·马歇尔, 王莹. 电磁轨道炮的科学与技术[M]. 北京: 兵器工业出版社, 2006.
[7] 李白, 鲁军勇, 谭赛, 等. 高速滑动电接触电枢表面动态磨损过程研究[J]. 电工技术学报, 2023, 38(1): 131-139.
Li Bai, Lu Junyong, Tan Sai, et al.Research on dynamic wear process of armature surface in high-speed sliding electric contact[J]. Transactions of China Electrotechnical Society, 2023, 38(1): 131-139.
[8] 曾竟成, 罗青, 唐羽章. 复合材料理化性能[M]. 长沙: 国防科技大学出版社, 1998.
[9] Banks-Sills L, Eliasi R, Berlin Y.Modeling of functionally graded materials in dynamic analyses[J]. Composites Part B: Engineering, 2002, 33(1): 7-15.
[10] 仲政, 吴林志, 陈伟球. 功能梯度材料与结构的若干力学问题研究进展[J]. 力学进展, 2010, 40(5): 528-541.
Zhong Zheng, Wu Linzhi, Chen Weiqiu.Progress in the study on mechanics problems of functionally graded materials and structures[J]. Advances in Mechanics, 2010, 40(5): 528-541.
[11] Paley M, Aboudi J.Micromechanical analysis of composites by the generalized cells model[J]. Mechanics of Materials, 1992, 14(2): 127-139.
[12] Siopis M J, Neu R W.Materials selection exercise for electromagnetic launcher rails[J]. IEEE Transactions on Magnetics, 2013, 49(8): 4831-4838.
[13] Gutierrez-Miravete E.Thermal stresses in functionally graded metal-ceramic plates[C]//Proceedings of the 2015 COMSOL Conference, Boston, USA, 2015: 1-4.
[14] Wakashima K, Hirano T, Nino M.Functionally gradient materials (FGM) architecture: a new type of ceramic-metal assemblage designed for hot structural components[C]//Proceedings of the ESA Symposium on Space Applications of Advanced Structural Materials (ESA SP-303), ESTEC-ESA, Noordwijk, The Netherlands,1990: 97-102.
[15] Koizumi M, Kawai T, Kude Y, et al.Recent developments in functionally gradient materials[J]. Materials and Processing Report, 1992, 7(3-4): 1-6.
[16] Ramu I, Mohanty S C.Modal analysis of functionally graded material plates using finite element method[J]. Procedia Materials Science, 2014, 6: 460-467.
[17] Saunders W L, Pendley K, Gutierrez-Miravete E.Modal analysis of functionally-graded metal-ceramic composite plates[C]//Proceedings of the 2014 COMSOL Conference, Boston, USA, 2014: 1-4.
[18] 李帅, 刘峰, 高翔, 等. 3种口径电磁轨道炮电磁特性研究[J]. 火炮发射与控制学报, 2020, 41(3): 1-5, 11.
Li Shuai, Liu Feng, Gao Xiang, et al.A study of electromagnetic characteristics of electromagnetic railguns of three different calibers[J]. Journal of Gun Launch & Control, 2020, 41(3): 1-5, 11.
[19] 高博, 邱群先, 郄文静, 等. 电磁轨道炮电枢多场耦合分析与试验研究[J]. 电工技术学报, 2020, 35(增刊2): 341-345.
Gao Bo, Qiu Qunxian, Qie Wenjing, et al.Multi-field coupling analysis and experimental research on armature of electromagnetic railgun[J]. Transactions of China Electrotechnical Society, 2020, 35(S2): 341-345.
[20] 马金财, 刘刚, 何龙. 基于电-热-力耦合的螺旋弹簧触指稳态温升分布仿真研究[J]. 高压电器, 2023, 59(8): 223-231.
Ma Jincai, Liu Gang, He Long.Simulation study on steady-state temperature rise distribution of helical spring contact finger based on electrical-thermal-mechanical coupling[J]. High Voltage Apparatus, 2023, 59(8): 223-231.
[21] 李春胜, 黄德彬. 金属材料手册[M]. 北京: 化学工业出版社, 2005.