气体添加对水电极同轴介质阻挡放电直接分解CO<sub>2</sub>的影响

doi:10.19595/j.cnki.1000-6753.tces.211442

Abstract
Figure/Table
References
Related Citation (15)

Download: PDF (5716 KB) HTML (1 KB)
Export: BibTeX | EndNote (RIS)

Abstract CO₂ conversion and utilization can convert the greenhouse gas into valuable fuels and chemicals, rather than regarding it as a waste. Due to the high stability of CO₂ molecules, the traditional methods for CO₂ conversion have limitations in terms of operating conditions, conversion and selectivity, catalyst preparation and activity maintenance. The rapid development of atmospheric pressure non-thermal plasma technology has provided new approaches for CO₂ conversion. Dielectric barrier discharge (DBD), as a main form of non-thermal plasma, has received extensive attention in the field of plasma CO₂ conversion. The performance of this process is affected by various factors, and it has been found that using the DBD reactor with water electrode and adding auxiliary gas (e.g., He, Ar and N₂) can improve the reaction performance to a certain extent. However, the research on the discharge characteristics and the reaction performance of CO₂ conversion in a DBD reactor with water electrode and auxiliary gas addition is limited. It is still unclear how to optimize the reaction process and performance. To address these issues, the direct decomposition of CO₂ has been performed in a DBD reactor with water electrode. The auxiliary gases He, Ar and N₂ are added into reactant stream with different concentrations to evaluate their influence on electrical characteristics and reaction performance of direct CO₂ decomposition process.
The DBD reactor is self-designed using quartz tube and stainless-steel rod. A casing tube is formed with two quartz tubes and the water at 0℃ circulates inside the casing tube, acting as the low voltage electrode. The stainless-steel rod is set coaxially with the inner quartz tube and acts as the high voltage electrode. The low voltage electrode is grounded after connecting to a reference capacitor. The DBD reactor is powered by custom-built AC power source. A Tektronix high-voltage probe and a Pearson current coil monitor are used to collect the applied voltage and the total current, while a Pintech differential probe is used to sample the voltage across the reference capacitor. All of these signals have been saved using a Tektronix digital oscilloscope. A Techcomp gas chromatography (GC) is used to analyze the gaseous products. The electrical characteristics has been obtained by analyzing the voltage-current wave forms and the Lissajous figure. Based on the voltage-current wave forms, the number of current spikes and the electron density are determined. While the discharge power and the breakdown voltage are calculated according to the Lissajous figure. The open-source software BOLSIG+ has been used to determine the average electron energy and the rate constant for electron impact excitation. The reaction rate for electron impact excitation is obtained by the electron density and the rate constant. The reaction performance is evaluated by the parameters of CO₂ conversion, CO yield and energy efficiency.
The following conclusions can be drawn: ① adding He, Ar and N₂ increases the discharge channels, and this effect is enhanced by increasing the concentrations of these gases. In addition, adding these gases increases the discharge power while reducing the breakdown voltage, so that more energy is used for the excitation of the gas molecules. ② Adding Ar and He increases the average electron energy and rate constant for electron impact excitation, but adding N₂ reduces these two parameters. Meanwhile, adding N₂ and Ar increases the electron density, which was reduced by adding He. Combing the electron density and the rate constant, the reaction rate for electron impact excitation is increased by increasing the concentration of these auxiliary gases, and the increasing trend follows the order of Ar>He>N₂. ③ For the reaction performance, the effect of these auxiliary gases also follows the order of Ar>He>N₂. The highest CO₂ conversion and CO yield is 15.2% and 9.3%, respectively, in the presence of 80% Ar. However, adding these gases reduces the process energy efficiency. Optimizing the reactor structure and operating parameters, and exploring a suitable high-performance catalyst are the feasible approaches to improve the process energy efficiency.

Key words： Dielectric barrier discharge with water electrode direct decomposition of CO₂ gas addition electrical characteristics energy efficiency

Received: 09 September 2021

PACS:

TM85

	Service

	E-mail this article
	Add to my bookshelf
	Add to citation manager
	E-mail Alert
	RSS
	Articles by authors
	Chen Huimin
	Duan Gehui
	Mei Danhua
	Liu Shiyun
	Fang Zhi

Cite this article:

Chen Huimin,Duan Gehui,Mei Danhua等. Effect of Gas Addition on CO₂ Decomposition in a Coaxial Dielectric Barrier Discharge Reactor with Water Electrode[J]. Transactions of China Electrotechnical Society, 2023, 38(1): 270-280.

URL:

https://dgjsxb.ces-transaction.com/EN/10.19595/j.cnki.1000-6753.tces.211442 OR https://dgjsxb.ces-transaction.com/EN/Y2023/V38/I1/270

[1] Clark M A, Domingo N G G, Colgan K, et al. Global food system emissions could preclude achieving the 1.5°and 2℃ climate change targets[J]. Science, 2020, 370(6517): 705-708.
[2] Hepburn C, Adlen E, Beddington J, et al.The technological and economic prospects for CO₂ utilization and removal[J]. Nature, 2019, 575(7781): 87-97.
[3] Modak A, Bhanja P, Dutta S, et al.Catalytic reduction of CO₂ into fuels and fine chemicals[J]. Green Chemistry, 2020, 22(13): 4002-4033.
[4] 王晓玲, 高远, 张帅, 等. 脉冲参数对介质阻挡放电等离子体CH₄干重整特性影响的实验[J]. 电工技术学报, 2019, 34(6): 1329-1337.
Wang Xiaoling, Gao Yuan, Zhang Shuai, et al.Effects of pulse parameters on dry reforming of CH₄ by pulsed DBD plasma[J]. Transactions of China Electrote-chnical Society, 2019, 34(6): 1329-1337.
[5] 戴栋, 宁文军, 邵涛. 大气压低温等离子体的研究现状与发展趋势[J]. 电工技术学报, 2017, 32(20): 1-9.
Dai Dong, Ning Wenjun, Shao Tao.A review on the state of art and future trends of atmospheric pressure low temperature plasmas[J]. Transactions of China Electrotechnical Society, 2017, 32(20): 1-9.
[6] Huang Bangdou, Zhang Cheng, Bai Han, et al.Energy pooling mechanism for catalyst-free methane activation in nanosecond pulsed non-thermal plasmas[J]. Chemical Engineering Journal, 2020, 396: 125185.
[7] Wang Weizong, Berthelot A, Kolev S, et al.CO₂ conversion in a gliding arc plasma: 1D cylindrical discharge model[J]. Plasma Sources Science and Technology, 2016, 25(6): 065012.
[8] 陈赦, 刘红梅, 吴婷, 等. 低温等离子体增强催化氨合成机理的一维流体动力学模型[J]. 电工技术学报, 2021, 36(13): 2730-2739.
Chen She, Liu Hongmei, Wu Ting, et al.1D fluid model of catalytic ammonia synthesis enhanced by low temperature plasma[J]. Transactions of China Electrotechnical Society, 2021, 36(13): 2730-2739.
[9] 鲁娜, 张楚珂, 夏芸, 等. 等离子体转化CO₂的研究进展[J]. 高电压技术, 2020, 46(1): 351-361.
Lu Na, Zhang Chuke, Xia Yun, et al.Advances in plasma technology for CO₂ conversion research[J]. High Voltage Engineering, 2020, 46(1): 351-361.
[10] 梅丹华, 方志, 邵涛. 大气压低温等离子体特性与应用研究现状[J]. 中国电机工程学报, 2020, 40(4): 1339-1358, 1425.
Mei Danhua, Fang Zhi, Shao Tao.Recent progress on characteristics and applications of atmospheric pressure low temperature plasmas[J]. Proceedings of the CSEE, 2020, 40(4): 1339-1358, 1425.
[11] 杨勇, 梅丹华, 段戈辉, 等. 不同电源激励Ar同轴介质阻挡放电特性对比[J]. 高电压技术, 2020, 46(12): 4355-4364.
Yang Yong, Mei Danhua, Duan Gehui, et al.Comparison of discharge characteristics of Ar coaxial dielectric barrier discharge dirven by different power supplies[J]. High Voltage Engineering, 2020, 46(12): 4355-4364.
[12] Kogelschatz U.Dielectric-barrier discharges: their history, discharge physics, and industrial applications[J]. Plasma Chemistry and Plasma Processing, 2003, 23(1): 1-46.
[13] 张晓星, 王宇非, 崔兆仑, 等. 不同填充材料对介质阻挡放电降解SF₆的实验研究[J]. 电工技术学报, 2021, 36(2): 397-406.
Zhang Xiaoxing, Wang Yufei, Cui Zhaolun, et al.Experimental study on the degradation of SF₆ by dielectric barrier discharge with different packing materials[J]. Transactions of China Electrotechnical Society, 2021, 36(2): 397-406.
[14] 张龙龙, 崔行磊, 刘峰, 等. 不同类型电源激励下HMDSO添加比例对Ar介质阻挡放电特性的影响[J]. 电工技术学报, 2021, 36(15): 3135-3146.
Zhang Longlong, Cui Xinglei, Liu Feng, et al.Effect of HMDSO addition ratio on Ar DBD characteristics excited by different types of power sources[J]. Transactions of China Electrotechnical Society, 2021, 36(15): 3135-3146.
[15] Wang Li, Du Xiaomin, Yi Yanhui, et al.Plasma-enhanced direct conversion of CO₂ to CO over oxygen-deficient Mo-doped CeO₂[J]. Chemical Communications, 2020, 56(94): 14801-14804.
[16] Li Ju, Zhai Xingwu, Ma Cunhua, et al.DBD plasma combined with different foam metal electrodes for CO₂ decomposition: experimental results and DFT validations[J]. Nanomaterials, 2019, 9(11): 1595.
[17] Yap D, Tatibouët J M, Batiot-Dupeyrat C.Carbon dioxide dissociation to carbon monoxide by non-thermal plasma[J]. Journal of CO₂ Utilization, 2015, 12: 54-61.
[18] Xu Shaojun, Khalaf P I, Martin P A, et al.CO₂ dissociation in a packed-bed plasma reactor: effects of operating conditions[J]. Plasma Sources Science and Technology, 2018, 27(7): 075009.
[19] Zhou Amin, Chen Dong, Dai Bin, et al.Direct decomposition of CO₂ using self-cooling dielectric barrier discharge plasma[J]. Greenhouse Gases: Science and Technology, 2017, 7(4): 721-730.
[20] Wang Li, Yi Yanhui, Guo Hongchen, et al.Atmospheric pressure and room temperature synthesis of methanol through plasma-catalytic hydrogenation of CO₂[J]. ACS Catalysis, 2018, 8(1): 90-100.
[21] Ozkan A, Dufour T, Silva T, et al.The influence of power and frequency on the filamentary behavior of a flowing DBD—application to the splitting of CO₂[J]. Plasma Sources Science and Technology, 2016, 25(2): 025013.
[22] Mei Danhua, Zhu Xinbo, He Yaling, et al.Plasma-assisted conversion of CO₂ in a dielectric barrier discharge reactor: understanding the effect of packing materials[J]. Plasma Sources Science and Technology, 2014, 24(1): 015011.
[23] Ramakers M, Michielsen I, Aerts R, et al.Effect of argon or helium on the CO₂ Conversion in a dielectric barrier discharge[J]. Plasma Processes and Polymers, 2015, 12(8): 755-763.
[24] Tu Xin, Gallon H J, Twigg M V, et al.Dry reforming of methane over a Ni/Al₂O₃ catalyst in a coaxial dielectric barrier discharge reactor[J]. Journal of Physics D: Applied Physics, 2011, 44(27): 274007.
[25] Duan Gehui, Fang Zhi, Fu Junhui, et al.Influence of water cooling for outer electrode on the discharge characteristics of an atmospheric coaxial DBD reactor[J]. IEEE Transactions on Plasma Science, 2021, 49(3): 1173-1180.
[26] Belov I, Paulussen S, Bogaerts A.Appearance of a conductive carbonaceous coating in a CO₂ dielectric barrier discharge and its influence on the electrical properties and the conversion efficiency[J]. Plasma Sources Science and Technology, 2016, 25(1): 015023.
[27] Aerts R, Somers W, Bogaerts A.Carbon dioxide splitting in a dielectric barrier discharge plasma: a combined experimental and computational study[J]. ChemSusChem, 2015, 8(4): 702-716.
[28] Xu Shaojun, Whitehead J C, Martin P A.CO₂ conversion in a non-thermal, barium titanate packed bed plasma reactor: the effect of dilution by Ar and N₂[J]. Chemical Engineering Journal, 2017, 327: 764-773.
[29] Snoeckx R, Heijkers S, van Wesenbeeck K, et al. CO₂ conversion in a dielectric barrier discharge plasma: N2 in the mix as a helping hand or problematic impurity?[J]. Energy & Environmental Science, 2016, 9(3): 999-1011.
[30] Lindon M A, Scime E E.CO₂ dissociation using the Versatile atmospheric dielectric barrier discharge experiment (VADER)[J]. Frontiers in Physics, 2014, 2: 55.
[31] Fridman A.Plasma chemistry[M]. Cambridge: Cambridge University Press, 2008.
[32] Aerts R, Martens T, Bogaerts A.Influence of vibrational states on CO₂ splitting by dielectric barrier discharges[J]. The Journal of Physical Chemistry C, 2012, 116(44): 23257-23273.
[33] Bogaerts A, Kozák T, van Laer K, et al. Plasma-based conversion of CO₂: current status and future challenges[J]. Faraday Discussions, 2015, 183: 217-232.
[34] Hagelaar G J M, Pitchford L C. Solving the Boltzmann equation to obtain electron transport coefficients and rate coefficients for fluid models[J]. Plasma Sources Science and Technology, 2005, 14(4): 722-733.
[35] Valdivia-Barrientos R, Pacheco-Sotelo J, Pacheco-Pacheco M, et al.Analysis and electrical modelling of a cylindrical DBD configuration at different operating frequencies[J]. Plasma Sources Science and Technology, 2006, 15(2): 237-245.