Abstract A disturbance feed-forward compensation method based on extended Kalman filter (EKF) was proposed for permanent magnet linear synchronous motor(PMLSM) servo system whichis vulnerable to influence of the external disturbance, such as friction force and force ripple. Firstly, disturbance model which consists of position dependent functions was developed and utilized as a disturbance feed-forward compensator. And then, the initial position of the translator was estimated by the EKF and reflected tothe disturbance feed-forward compensator. Also, the coefficients of the disturbance model were adjusted adaptively to create synchronization between the model and real disturbance and compensate system disturbance. Finally, the system simulation and experimental results confirm that the proposed scheme is effective and feasible. Compared with the disturbance observer, PMLSM servo system based on EKF has superiorperformance in disturbance compensation.
Zhao Ximei,Wu Wenbin,Zhu Guoxin. Disturbance Feed-Forward Compensation for High-SpeedPermanent Magnet Linear Synchronous Motor Based on Extended Kalman Filter[J]. Transactions of China Electrotechnical Society, 2018, 33(7): 1516-1522.
[1] 王一光, 李晓杰, 陈兴林. 基于永磁直线同步电机的光刻机掩模台鲁棒自适应神经网络控制[J]. 电工技术学报, 2016, 31(6): 38-46. Wang Yiguang, Li Xiaojie, Chen Xinglin.A robust adaptive neural network control method based on permanent magnetic linear synchronous motor for the reticle stage of lithography[J]. Transactions of China Electrotechnical Society, 2016, 31(6): 38-46. [2] Wang Mingyi, Li Liyi, Pan Donghua.Detent force compensation for PMLSM systems based on structural design and control method combination[J]. IEEE Transactions on Industrial Electronics, 2015, 62(11): 6845-6854. [3] 孟高军, 余海涛, 胡敏强, 等. 一种基于非线性反馈重复控制策略的磁通切换直线电机推力波动抑制方法[J]. 电工技术学报, 2017, 32(8): 169-177. MengGaojun, Yu Haitao, Hu Minqiang, et al. Thrust ripple suppression for linear flux-switching permanent magnet machine based on a repetitive control strategy of nonlinear feedback[J]. Transactions of China Electrotechnical Society, 2017, 32(8): 169-177. [4] 刘春芳, 刘志. 基于分数阶PID和重复控制的快速刀具伺服系统[J]. 沈阳工业大学学报, 2017, 39(5): 486-490. Liu Chunfang, Liu Zhi.Fast tool servo system based on fractional order PID and repetitive control[J]. Journal of Shenyang University of Technology, 2017, 39(5): 486-490. [5] Panah P G, Ataei M, Mirzaeian B, et al.A robust adaptive sliding mode control for PMLSM with variable velocity profile over wide range[J]. Research Journal of Applied Sciences Engineering & Technology, 2015, 10(9): 997-1006. [6] Hua C, Rao Z, Na T, et al.Nonlinear dynamics of rub-impact on a rotor-rubber bearing system with the Stribeck friction model[J]. Journal of Mechanical Science & Technology, 2015, 29(8): 3109-3119. [7] Kim K, Kim J, Choi Y M, et al.Hybrid control system for compensation of the force ripple in permanent magnet linear motor[J]. Journal of Computational & Theoretical Nanoscience, 2012, 13(1): 132-136. [8] 支凡, 张鸣, 朱煜, 等. 无铁心永磁同步直线电机推力谐波分析与消除[J].中国电机工程学报, 2017, 37(7): 2101-2109. Zhi Fan, Zhang Ming, Zhu Yu, et al.Analysis and elimination of harmonics in force of ironless permanent magnet linear synchronous motor[J]. Proceedings of the CSEE, 2017, 37(7): 2101-2109. [9] Bascetta L, Rocco P, Magnani G.Force ripple compensation in linear motors based on closed-loop position-dependent identification[J]. IEEE/ASME Transactions on Mechatronics, 2010, 15(3): 349-359. [10] Zhao Shoujun, Tan K K.Adaptive feedforward compensation of force ripples in linear motors[J]. Control Engineering Practice, 2005, 13(9): 1081-1092. [11] 赵希梅, 赵久威, 李洪谊, 等. 基于GPC和DOB的直驱XY平台鲁棒跟踪控制[J]. 电工技术学报, 2015, 30(6): 150-154. Zhao Ximei, Zhao Jiuwei, Li Hongyi, et al.Robust tracking control for direct drive XY table based on GPC and DOB[J]. Transactions of China Electrotechnical Society, 2015, 30(6): 150-154. [12] 陈炜, 郭照升, 夏长亮, 等. 基于转动惯量辨识的交流伺服系统自适应扰动观测器设计[J]. 电工技术学报, 2016, 31(16): 34-42. Chen Wei, GuoZhaosheng, Xia Changliang, et al. Design of adaptive disturbance observer for AC servo system with inertia identification[J]. Transactions of China Electrotechnical Society, 2016, 31(16): 34-42.
2018, Vol. 33 
