基于环流优化的桥臂复用型模块化多电平换流器能量平衡策略研究

doi:10.19595/j.cnki.1000-6753.tces.250621

Abstract
Figure/Table
References
Related Citation (7)

Download: PDF (7501 KB) HTML (1 KB)
Export: BibTeX | EndNote (RIS)

Abstract The modular multilevel converter (MMC), characterized by its modularity, superior waveform quality, and scalability, has emerged as a pivotal topology in flexible high-voltage direct current (HVDC) transmission systems. However, its large-scale deployment on offshore platforms and in urban grid interconnections is hindered by excessive volume and weight, primarily due to cascaded submodules (SMs). Hybrid MMC topologies that integrate device series connection and SM cascading have emerged as promising solutions for enhancing power density. Nevertheless, the energy balance challenge caused by segmented sinusoidal waveforms and current-path switching in such topologies severely limits their engineering viability. Traditional energy-balancing approaches, including arm voltage control and harmonic current injection, have significant drawbacks: limited voltage regulation ranges, increased hardware complexity, and reduced efficiency. This study focuses on the arm-multiplexing MMC (AM-MMC), a lightweight topology with relatively good performance, to address these limitations through circulating-current-optimized energy-balancing control.
Firstly, a high-dimensional dynamic model based on arm equivalent modulation (AEM) strategy is established to express the time-varying coupling effects inherent to AM-MMC’s multiplexed arm operation. The model elucidates the mechanism of circulating current generation through precise analysis of submodule capacitor voltage components, the nonlinear characteristics of dynamic switching functions, and multi-frequency harmonic voltage-current interactions. Secondly, the energy balance and the quantitative characterization of circulating current involvement in energy balance processes are analyzed. With retaining the second-harmonic component of the circulating current for simplified control, a fundamental characteristic of the AM-MMC is identified. That is, the minimum required amplitude of the second-harmonic circulating current maintains a constant proportion with the DC-side current when the modulation ratio is held constant. Then, a methodology is established to determine this proportionality coefficient across different modulation ratios. Finally, a control strategy for circulating current optimization is proposed. Given the complexity of calculating proportionality coefficients, an offline coefficient configuration is adopted to ensure the dynamic performance of the proposed strategy. However, due to the linearization and averaging approximations in the mathematical modeling process, the theoretically derived coefficients inevitably contain certain inaccuracies. To further improve control precision, an online optimization section is introduced. This section integrates the submodule capacitor’s voltage feedback with a PI controller to optimize real-time coefficients, and a PIR controller regulates the circulating current.
A cross-scale verification platform is developed, including an 85 MV·A/±35 kV simulation system and a 3.2 kV·A/±150 V hardware prototype. The following conclusions can be drawn. (1) The proposed strategy achieves optimal coordination between energy balance and circulating current suppression, while addressing the limitations of additional hardware requirements and voltage regulation constraints. (2) By the dominant harmonic component regulation with offline-predetermined coefficients and online optimization, this approach ensures dynamic stability and a wide voltage regulation range with minimal trade-offs in scenarios like offshore wind farm integration, where a lightweight topology is required. Thus, an economically viable and efficient engineering solution can be offered. (3) Beyond specific implementations, the developed methodology establishes a universal framework for lightweight topologies. As an inherent characteristic of MMCs, the circulating current enables facile control without additional hardware requirements for energy balance control.

Key words： Modular multilevel converter (MMC) lightweight design arm-multiplexing circulating current optimization energy balance control

Received: 14 April 2025

PACS:

TM721.1

	Service

	E-mail this article
	Add to my bookshelf
	Add to citation manager
	E-mail Alert
	RSS
	Articles by authors
	Zhang Zhen
	Wang Yi
	Liu Bowen
	Yang Shun
	Gao Yuhua

Cite this article:

Zhang Zhen,Wang Yi,Liu Bowen等. Research on Energy Balance Strategy of Arm Multiplexing Modular Multilevel Converter Based on Circulating Current Optimization[J]. Transactions of China Electrotechnical Society, 2026, 41(8): 2697-2717.

URL:

https://dgjsxb.ces-transaction.com/EN/10.19595/j.cnki.1000-6753.tces.250621 OR https://dgjsxb.ces-transaction.com/EN/Y2026/V41/I8/2697

[1] 高本锋, 沈雨思, 宋瑞华, 等. 虚拟同步机控制模块化多电平变流器阻抗建模及次/超同步振荡稳定性分析[J]. 电工技术学报, 2025, 40(2): 559-573.
Gao Benfeng, Shen Yusi, Song Ruihua, et al.Impedance modeling and sub/super synchronous oscillation stability analysis of modular multilevel converter under virtual synchronous generator control[J]. Transactions of China Electrotechnical Society, 2025, 40(2): 559-573.
[2] 吴丽丽, 茆美琴, 施永. 含主动限流控制的MMC-HVDC电网直流短路故障电流解析计算[J]. 电工技术学报, 2024, 39(3): 785-797.
Wu Lili, Mao Meiqin, Shi Yong.Analytical calculation of DC short-circuit fault current of modular multi-level converter-HVDC grid with active current limiting control[J]. Transactions of China Electrotechnical Society, 2024, 39(3): 785-797.
[3] 刘欣, 袁易, 王利桐, 等. 柔性直流输电系统三端口混合参数建模及其稳定性分析[J]. 电工技术学报, 2024, 39(16): 4968-4984.
Liu Xin, Yuan Yi, Wang Litong, et al.Three-port hybrid parameter modeling and stability analysis of MMC-HVDC system[J]. Transactions of China Elec-trotechnical Society, 2024, 39(16): 4968-4984.
[4] 王锐, 王毅, 杨晗菲, 等. 具有宽运行范围的混合复用型模块化多电平拓扑及其能量均衡控制策略[J]. 电工技术学报, 2025, 40(15): 4740-4754.
Wang Rui, Wang Yi, Yang Hanfei, et al.A hybrid multiplexing MMC topology with wide operating range and energy balance control strategy[J]. Transa-ctions of China Electrotechnical Society, 2025, 40(15): 4740-4754.
[5] 李婧靓, 黄伟煌, 刘涛, 等. 特高压多端混合直流输电系统的控制策略研究[J]. 南方电网技术, 2018, 12(2): 47-55.
Li Jingjing, Huang Weihuang, Liu Tao, et al.Research on control strategy of multi-terminal hybrid UHVDC transmission system[J]. Southern Power System Technology, 2018, 12(2): 47-55.
[6] 杨雪飞, 杨绍远, 李桂源, 等. 昆柳龙直流工程柳州站双阀组充电跳闸事件分析及对策[J]. 南方电网技术, 2022, 16(2): 82-88.
Yang Xuefei, Yang Shaoyuan, Li Guiyuan, et al.Analysis of the kunliulong UHVDC tripping event during charging process of high and low values in Liuzhou converter station and countermeasure[J]. Southern Power System Technology, 2022, 16(2): 82-88.
[7] 蔡旭, 杨仁炘, 周剑桥, 等. 海上风电直流送出与并网技术综述[J]. 电力系统自动化, 2021, 45(21): 2-22.
Cai Xu, Yang Renxin, Zhou Jianqiao, et al.Review on offshore wind power integration via DC transmi-ssion[J]. Automation of Electric Power Systems, 2021, 45(21): 2-22.
[8] 梁富胜, 伦灿章, 熊根, 等. 大型海上换流站浮托安装数值模拟和实测分析[J]. 中国海洋平台, 2023, 38(4): 27-35, 79.
Liang Fusheng, Lun Canzhang, Xiong Gen, et al.Numerical simulation and field measurement analysis on floatover installation of large offshore converter station[J]. China Offshore Platform, 2023, 38(4): 27-35, 79.
[9] 秦康, 曹雨, 卢毓欣, 等. 海上换流站平台结构设计[J]. 中国海洋平台, 2024, 39(4): 86-92.
Qin Kang, Cao Yu, Lu Yuxin, et al.Structural design of offshore converter station platform[J]. China Offshore Platform, 2024, 39(4): 86-92.
[10] Tang Yuan, Chen Minjie, Ran Li.A compact MMC submodule structure with reduced capacitor size using the stacked switched capacitor architecture[J]. IEEE Transactions on Power Electronics, 2016, 31(10): 6920-6936.
[11] Li Rui, Fletcher J E, Xu Lie, et al.Enhanced flat-topped modulation for MMC control in HVDC transmission systems[J]. IEEE Transactions on Power Delivery, 2017, 32(1): 152-161.
[12] 董鹏, 蔡旭, 吕敬. 大幅减小子模块电容容值的MMC优化方法[J]. 中国电机工程学报, 2018, 38(18): 5369-5380.
Dong Peng, Cai Xu, Lü Jing.Optimized method of MMC for greatly reducing the capacitance of the submodules[J]. Proceedings of the CSEE, 2018, 38(18): 5369-5380.
[13] Mishra R, Vaghasiya K M, Agarwal V.A high voltage gain capable MMC for offshore wind farms: frequency component analysis and minimization of capacitor voltage ripple[J]. IEEE Transactions on Industrial Electronics, 2022, 69(12): 11957-11967.
[14] Li Rui, Adam G P, Holliday D, et al.Hybrid cascaded modular multilevel converter with DC fault ride-through capability for the HVDC transmission system[J]. IEEE Transactions on Power Delivery, 2015, 30(4): 1853-1862.
[15] Yang Heya, Fan Shiyuan, Dong Yufei, et al.Arm phase-shift conducting modulation for alternate arm multilevel converter with half-bridge submodules[J]. IEEE Transactions on Power Electronics, 2021, 36(5): 5223-5235.
[16] 高玉华, 王琛, 王毅, 等. 基于半波交替的轻型化MMC拓扑及控制策略[J]. 电力系统自动化, 2023, 47(17): 149-159.
Gao Yuhua, Wang Chen, Wang Yi, et al.Topology and control strategy of light-weight modular multi-level converter with half-wave alternating[J]. Auto-mation of Electric Power Systems, 2023, 47(17): 149-159.
[17] Hassan Z, Watson A J, Tardelli F, et al.A switched mid-point modular multilevel converter for HVDC applications[J]. IEEE Transactions on Power Delivery, 2023, 38(3): 1534-1547.
[18] Patro S K, Shukla A.Control and derived topologies of parallel hybrid converter[J]. IEEE Transactions on Industry Applications, 2021, 57(1): 598-613.
[19] Wickramasinghe H R, Konstantinou G, Li Zixin, et al.Alternate arm converters-based HVDC model com-patible with the CIGRE B4 DC grid test system[J]. IEEE Transactions on Power Delivery, 2018, 34(1): 149-159.
[20] 张建坡, 赵成勇. 模块化多电平换流器环流及抑制策略研究[J]. 电工技术学报, 2013, 28(10): 328-336.
Zhang Jianpo, Zhao Chengyong.Research on circu-lation current and suppressing strategy of modular multilevel converter[J]. Transactions of China Elec-trotechnical Society, 2013, 28(10): 328-336.
[21] Reddy G A, Shukla A.Circulating current optimi-zation control of MMC[J]. IEEE Transactions on Industrial Electronics, 2021, 68(4): 2798-2811.
[22] Wang Yi, Zhang Zhen, Xu Yutao, et al.Topology and control of an arm multiplexing MMC with full-range voltage regulation[J]. IEEE Transactions on Power Electronics, 2024, 39(12): 16135-16151.
[23] 王琛, 陶建业, 王毅, 等. 桥臂复用型模块化多电平换流器的拓扑及控制研究[J]. 中国电机工程学报, 2022, 42(9): 3373-3385.
Wang Chen, Tao Jianye, Wang Yi, et al.Research on topology and control of arm multiplexing modular multilevel converter[J]. Proceedings of the CSEE, 2022, 42(9): 3373-3385.
[24] 李宇薇, 王毅, 高玉华, 等. 桥臂复用模块化多电平变流器单极接地故障无闭锁穿越及能量均衡[J]. 电工技术学报, 2025, 40(1): 190-202.
Li Yuwei, Wang Yi, Gao Yuhua, et al.Pole-to-ground fault riding-through and energy balance of arm-multiplexing modular multilevel converter[J]. Transa-ctions of China Electrotechnical Society, 2025, 40(1): 190-202.
[25] 阎发友, 汤广福, 贺之渊, 等. 一种适用于模块化多电平换流器的新型环流控制器[J]. 电力系统自动化, 2014, 38(1): 104-108, 120.
Yan Fayou, Tang Guangfu, He Zhiyuan, et al.A novel circulating current controller for modular multilevel converter[J]. Automation of Electric Power Systems, 2014, 38(1): 104-108, 120.
[26] Moon J W, Kim C S, Park J W, et al.Circulating current control in MMC under the unbalanced voltage[J]. IEEE Transactions on Power Delivery, 2013, 28(3): 1952-1959.
[27] 伍小杰, 杨超, 公铮, 等. 基于多谐振控制器的MMC简化环流抑制策略[J]. 电工技术学报, 2016, 31(13): 74-81.
Wu Xiaojie, Yang Chao, Gong Zheng, et al.Simplified circulating current suppressing strategy for MMC based on multi-resonant controller[J]. Transa-ctions of China Electrotechnical Society, 2016, 31(13): 74-81.
[28] Li Jianguo, Zhao Xiongguang, Song Qiang, et al.Loss calculation method and loss characteristic analysis of MMC based VSC-HVDC system[C]//2013 IEEE International Symposium on Industrial Electronics, Taipei, China, 2013: 1-6.
[29] 屠卿瑞, 徐政, 管敏渊, 等. 模块化多电平换流器环流抑制控制器设计[J]. 电力系统自动化, 2010, 34(18): 57-61, 83.
Tu Qingrui, Xu Zheng, Guan Minyuan, et al.Design of circulating current suppressing controllers for modular multilevel converter[J]. Automation of Electric Power Systems, 2010, 34(18): 57-61, 83.