复合圆筒型永磁直线作动器热网络模型与热性能研究

doi:10.19595/j.cnki.1000-6753.tces.241282

Abstract
Figure/Table
References
Related Citation (11)

Download: PDF (8126 KB) HTML (1 KB)
Export: BibTeX | EndNote (RIS)

Abstract The compound tubular permanent magnet linear actuator (CTPMLA) integrates a passive damping system with a tubular permanent magnet linear synchronous motor. It provides a continuous thrust of 1 076 N and a maximum damping force of 2 754 N, suitable for vehicles' active suspension systems. The primary structure comprises a solid iron core and solid aluminum rings in slot opening, which has induced eddy currents during the movement of the mover and generates additional damping force. However, the increase in eddy current losses leads to significant temperature rises due to the limited heat dissipation capacity of the tubular design. High temperatures can adversely affect the output performance of the CTPMLA, pose risks of permanent magnet demagnetization, and accelerate the aging of the winding insulation. Therefore, it is crucial to investigate the rise in temperature of the CTPMLA.
The copper losses in the windings are the predominant loss in the electric state, reaching 164.26 W. The second loss is the eddy current losses of the aluminum rings, reaching 24.42 W, which significantly exceeds the losses in the stator core despite their small volume. For modeling convenience, regard the insulation varnish, air, and slot insulation within the stator model as a uniform insulating material and the copper as a homogeneous entity. The CTPMLA is divided into three sections based on heat flow paths. A thermal network model for individual slots is established to create a multi-node thermal network model for all sections. The Reynolds number is calculated for various surfaces to assess airflow patterns, facilitating the determination of convective heat transfer coefficients and thermal resistances.
Then, an electromagnetic-thermal coupling calculation process is developed to explain the impact of temperature on material conductivity and air thermal parameters. The data is exchanged by a couple of inputs and outputs between the electromagnetic and thermal models, and the losses, convective thermal resistances, and gap thermal resistances are iteratively updated until temperature convergence is achieved. The temperature field of the CTPMLA is calculated via varying vehicle speeds and currents under electric and locked rotor states. Results indicate that the maximum value of the average winding temperature reaches 121.9℃ in the electric state, while the maximum value of the average temperature of the permanent magnets is 81.58℃. At locked rotor states, the maximum value of average winding temperature is 108.5℃, while that of permanent magnets is 89.8℃. All temperatures are significantly below the limited temperature of 180℃ of insulating materials and permanent magnets.
Finally, the comparison is carried out with a three-dimensional finite element temperature field model. The errors are 4% for the windings and 3.1% for the permanent magnets, which demonstrates the efficiency of the thermal network coupling model. Moreover, its computation time is only 10.9% of the finite element model. Based on the developed prototype, the temperature experiments of the locked rotor are carried out under natural and forced convection conditions. The error margin is less than 4%, verifying the effectiveness of the proposed thermal network coupling model.

Key words： Compound tubular permanent magnet linear actuator (CTPMLA) damping rings thermal network model bidirectional coupling

Received: 19 July 2024

PACS:

TM359.4

Fund:国家自然科学基金资助项目（NFSC52177061）

Corresponding Authors: 卢琴芬女,1972年生,教授,博士生导师,研究方向为直线电机及特种永磁电机的优化设计、驱动控制及应用技术等。E-mail: luqinfen@zju.edu.cn

	Service

	E-mail this article
	Add to my bookshelf
	Add to citation manager
	E-mail Alert
	RSS
	Articles by authors
	Feng Yunnan
	Wu Lize
	Li Yanxin
	Lu Qinfen

Cite this article:

Feng Yunnan,Wu Lize,Li Yanxin等. Research on Thermal Network Model and Thermal Performance of Compound Tubular Permanent Magnet Linear Actuator[J]. Transactions of China Electrotechnical Society, 2025, 40(18): 5854-5865.

URL:

https://dgjsxb.ces-transaction.com/EN/10.19595/j.cnki.1000-6753.tces.241282 OR https://dgjsxb.ces-transaction.com/EN/Y2025/V40/I18/5854

[1] 关涛, 刘大猛, 何永勇. 永磁轮毂电机技术发展综述[J]. 电工技术学报, 2024, 39(2): 378-396.
Guan Tao, Liu Dameng, He Yongyong.Review on development of permanent magnet in-wheel motors[J]. Transactions of China Electrotechnical Society, 2024, 39(2): 378-396.
[2] 殷珺, 罗建南, 喻凡. 汽车电磁式主动悬架技术综述[J]. 机械设计与研究, 2020, 36(1): 161-168.
Yin Jun, Luo Jiannan, Yu Fan.The-state-of-art review on automotive electromagnetic active suspension technology[J]. Machine Design & Research, 2020, 36(1): 161-168.
[3] East W, Turcotte J, Plante J S, et al.Experimental assessment of a linear actuator driven by mag-netorheological clutches for automotive active suspensions[J]. Journal of Intelligent Material Systems and Structures, 2021, 32(9): 955-970.
[4] 龚夕霞, 李焱鑫, 卢琴芬. 模块化永磁直线同步电机考虑制造公差的推力鲁棒性优化[J]. 电工技术学报, 2024, 39(2): 465-474, 513.
Gong Xixia, Li Yanxin, Lu Qinfen.Thrust robustness optimization of modular permanent magnet linear synchronous motor accounting for manufacture tolerance[J]. Transactions of China Electrotechnical Society, 2024, 39(2): 465-474, 513.
[5] 颜建虎, 李彪, 时岩, 等. 主动悬架用非均匀齿圆筒型永磁直线电机多目标分层优化设计[J]. 兵工学报, 2023, 44(1): 40-50.
Yan Jianhu, Li Biao, Shi Yan, et al.Multi-objective stratified optimization design of tubular permanent magnet linear motors with nonuniform teeth for active suspension[J]. Acta Armamentarii, 2023, 44(1): 40-50.
[6] Eckert P R, Flores Filho A F, Perondi E A, et al. Dual quasi-halbach linear tubular actuator with coreless moving-coil for semiactive and active suspension[J]. IEEE Transactions on Industrial Electronics, 2018, 65(12): 9873-9883.
[7] 寇发荣, 武江浩, 许家楠, 等. 整车电磁混合主动悬架故障诊断与容错控制研究[J]. 振动与冲击, 2022, 41(4): 101-109.
Kou Farong, Wu Jianghao, Xu Jianan, et al.A study on fault diagnosis and fault tolerant control of vehicle electromagnetic hybrid active suspension[J]. Journal of Vibration and Shock, 2022, 41(4): 101-109.
[8] Ding Renkai, Wang Ruochen, Meng Xiangpeng, et al.A modified energy-saving skyhook for active suspension based on a hybrid electromagnetic actuator[J]. Journal of Vibration and Control, 2019, 25(2): 286-297.
[9] Xu Ziyi, Xu Yongming, Gai Yaohui, et al.Thermal management of drive motor for transportation: analysis methods, key factors in thermal analysis, and cooling methods: a review[J]. IEEE Transactions on Transportation Electrification, 2023, 9(3): 4751-4774.
[10] 张健, 朱锡庆, 张卓然, 等. 电励磁双凸极无刷直流发电机热网络建模与热特性研究[J]. 中国电机工程学报, 2023, 43(1): 318-329.
Zhang Jian, Zhu Xiqing, Zhang Zhuoran, et al.Thermal network modeling and thermal characteri-stics analysis of doubly salient brushless DC generator with stator field winding[J]. Proceedings of the CSEE, 2023, 43(1): 318-329.
[11] 陈前, 赵美玲, 廖继红, 等. 轻量化高效率永磁电机及其控制技术综述[J]. 电气工程学报, 2023, 18(4): 3-19.
Chen Qian, Zhao Meiling, Liao Jihong, et al.Review on lightweight and high efficiency permanent magnet motor and its control techniques[J]. Journal of Electrical Engineering, 2023, 18(4): 3-19.
[12] 林明耀, 乐伟, 林克曼, 等. 轴向永磁电机热设计及其研究发展综述[J]. 中国电机工程学报, 2021, 41(6): 1914-1929.
Lin Mingyao, Le Wei, Lin Keman, et al.Overview on research and development of thermal design methods of axial flux permanent magnet machines[J]. Pro-ceedings of the CSEE, 2021, 41(6): 1914-1929.
[13] 张兆宇, 于思洋, 张岳, 等. 永磁/磁阻混合转子双定子低速大转矩同步电机冷却及热管理技术研究[J]. 电机与控制学报, 2023, 27(11): 114-124.
Zhang Zhaoyu, Yu Siyang, Zhang Yue, et al.Cooling and thermal management technology for low speed and high torque synchronous motor with permanent magnet and reluctance hybrid rotor and double stator[J]. Electric Machines and Control, 2023, 27(11): 114-124.
[14] 缠东辉, 王桢, 任韶华, 等. 5.5 MW半直驱中速永磁风力发电机温度场分析[J]. 微电机, 2024, 57(9): 66-69.
Chan Donghui, Wang Zhen, Ren Shaohua, et al.Temperature field analysis of 5.5 MW hybrid drive medium speed permanent magnet wind generator[J]. Micromotors, 2024, 57(9): 66-69.
[15] 王小飞, 代颖, 罗建. 基于流固耦合的车用永磁同步电机水道设计与温度场分析[J]. 电工技术学报, 2019, 34(增刊1): 22-29.
Wang Xiaofei, Dai Ying, Luo Jian.Waterway design and temperature field analysis of vehicle permanent magnet synchronous motor based on fluid-solid coupling[J]. Transactions of China Electrotechnical Society, 2019, 34(S1): 22-29.
[16] 谢颖, 胡圣明, 陈鹏, 等. 永磁同步电机匝间短路故障温度场分析[J]. 电工技术学报, 2022, 37(2): 322-331.
Xie Ying, Hu Shengming, Chen Peng, et al.Thermal field analysis on inter-turn short circuit fault of permanent magnet synchronous motor[J]. Transa-ctions of China Electrotechnical Society, 2022, 37(2): 322-331.
[17] 陈鹏, 谢颖, 李道璐. 感应电机定子匝间短路故障温升特性研究[J]. 电工技术学报, 2023, 38(18): 4875-4888.
Chen Peng, Xie Ying, Li Daolu.Research on the temperature rise characteristics of induction motors with stator inter-turn fault[J]. Transactions of China Electrotechnical Society, 2023, 38(18): 4875-4888.
[18] Tong Wenming, Sun Ruolan, Li Shiqi, et al.Loss and thermal analysis for high-speed amorphous metal PMSMs using 3-D electromagnetic-thermal bi-directional coupling[J]. IEEE Transactions on Energy Conversion, 2021, 36(4): 2839-2849.
[19] 崔刚, 熊斌, 黄康杰, 等. 电动汽车用永磁电机的失磁空间分布特性及影响因素研究[J]. 电工技术学报, 2023, 38(22): 5959-5974.
Cui Gang, Xiong Bin, Huang Kangjie, et al.Study on spatial distribution characteristics and influencing factors of permanent magnet motor for electric vehicle loss of excitation[J]. China Industrial Economics, 2023,38(22): 5959-5974.
[20] Mo Lihong, Zhu Xiaoyong, Zhang Tao, et al.Temperature rise calculation of a flux-switching permanent-magnet double-rotor machine using electromagnetic-thermal coupling analysis[J]. IEEE Transactions on Magnetics, 2018, 54(3): 8201004.
[21] 吴胜男, 郝大全, 佟文明. 基于等效热网络法和CFD法高速永磁同步电机热计算研究[J]. 电机与控制学报, 2022, 26(7): 29-36.
Wu Shengnan, Hao Daquan, Tong Wenming.Thermal calculation of high speed permanent magnet synchronous motor based on equivalent thermal network and CFD method[J]. Electric Machines and Control, 2022, 26(7): 29-36.
[22] 吴胜男, 郝大全, 佟文明, 等. 基于集中参数热模型的大功率模块化定子混合励磁同步电机热分析[J]. 中国电机工程学报, 2020, 40(24): 7851-7859, 8222.
Wu Shengnan, Hao Daquan, Tong Wenming, et al.Thermal analysis of large hybrid excitation syn-chronous machine with modular stator and consequent pole rotor based on lumped parameter thermal network[J]. Proceedings of the CSEE, 2020, 40(24): 7851-7859, 8222.
[23] 杨世铭, 陶文铨. 传热学[M]. 4版. 北京: 高等教育出版社, 2006.