基于铜环驱动的TA2钛板电磁成形数值模拟与实验研究

doi:10.19595/j.cnki.1000-6753.tces.240834

Abstract
Figure/Table
References
Related Citation (15)

Download: PDF (31633 KB) HTML (1 KB)
Export: BibTeX | EndNote (RIS)

Abstract Electromagnetic drive forming technology is a special forming process that uses pulsed Lorentz force to drive a high-conductivity sheet to move, thereby driving a low-conductivity sheet to cause plastic deformation, which can effectively make up for the shortage of traditional electromagnetic forming in forming low-conductivity materials. However, in the existing electromagnetic drive forming, the driver sheet also undergoes plastic deformation, which tends to lead to a serious problem of wastage of the driver sheet, and it is difficult to regulate the forming shape.
To solve this, instead of the traditional circular drive sheet, a solid copper ring with a specific thickness is employed, utilizing the strong electromagnetic force generated in the copper ring to propel it at high speed into collision with a metal sheet. This impact generates a contact force, causing the sheet to undergo plastic deformation. Additionally, an electromagnetic-structural coupling model for the copper ring electromagnetic drive forming process is developed using LS-DYNA software. A series of electromagnetic drive forming experiments are then conducted, using a TA2 titanium plate as the test material, to validate the feasibility of the proposed method. Numerical simulation and experimental results show that under a single discharge (7 kV), a metallic copper ring with a diameter of 80 mm can drive the titanium plate to deform and the forming height can reach 14 mm. Meanwhile, based on strain analysis of the forming sheet and the driven ring, the solid copper ring does not deform and can be reused. In addition, by changing the size and shape of the copper ring, the forming profile of the plate can be flexibly adjusted. For example, when the diameters of the circular driving rings are 65, 80, and 95 mm, uniformly deformed areas with diameters of 58, 72, and 87 mm are observed on the top of the sheet, which is highly consistent with the shape of the rings. Even if the forming height is increased, the forming shape of the center area of the sheet remains a flat-topped profile when enhancing the discharge voltages. On this basis, the dynamic deformation process of the sheet is further investigated through numerical methods, to reveal the deformation behavior and forming mechanism of the titanium plate driven by the copper ring, which demonstrates that the forming velocity approaching 100 m/s and the strain rate is up to 1 000 s^-1. Hence, this forming process belongs to the category of high-speed forming technology.
The obtained results indicate that, since the copper ring is a solid ring with a specific thickness, it does not experience plastic deformation during the electromagnetic drive forming process and can be reused. This effectively addresses the issue of excessive waste of the driver sheet in conventional electromagnetic drive forming. The copper ring also provides shape adjustment capabilities, allowing for the formation of sheets with circular, quadrilateral, and hexagonal flat tops. The height of the flat-topped profile can be controlled by adjusting the discharge voltage, overcoming the problem of limited shape flexibility in existing electromagnetic drive forming methods. These results are of significant practical value for advancing and expanding the applications of electromagnetic drive forming technology.

Key words： Electromagnetic forming drive forming titanium plate deformation morphology control

Received: 19 May 2024

PACS:

TM154

	Service

	E-mail this article
	Add to my bookshelf
	Add to citation manager
	E-mail Alert
	RSS
	Articles by authors
	Zhang Wang
	Zhu Xinhui
	Qiu Li
	Ouyang Shaowei

Cite this article:

Zhang Wang,Zhu Xinhui,Qiu Li等. Numerical and Experimental Study of Electromagnetic Drive Forming for TA2 Titanium Sheet Based on a Copper Ring[J]. Transactions of China Electrotechnical Society, 2025, 40(11): 3339-3348.

URL:

https://dgjsxb.ces-transaction.com/EN/10.19595/j.cnki.1000-6753.tces.240834 OR https://dgjsxb.ces-transaction.com/EN/Y2025/V40/I11/3339

[1] 熊奇, 邱爽, 李彦昕, 等. 组合式电磁成形技术研究进展[J]. 电工技术学报, 2024, 39(9): 2710-2729.
Xiong Qi, Qiu Shuang, Li Yanxin, et al.Research progress of combined electromagnetic forming technology[J]. Transactions of China Electrotechnical Society, 2024, 39(9): 2710-2729.
[2] 朱成席, 徐杰, 于海平, 等. 电磁微成形技术研究进展[J]. 塑性工程学报, 2023, 30(6): 22-36.
Zhu Chengxi, Xu Jie, Yu Haiping, et al.Research progress of electromagnetic micro-forming techno- logy[J]. Journal of Plasticity Engineering, 2023, 30(6): 22-36.
[3] Chu Guannan, Sun Lei, Wang Guodong, et al.Axial hydro-forging sequence for variable-diameter tube of 6063 aluminum alloy[J]. Journal of Materials Pro- cessing Technology, 2019, 272: 87-99.
[4] Sun Wen, Liu Wei, Yuan Shijian.Suppressing wrinkles in thin-walled dome parts: a novel deep drawing method with active stress control[J]. Journal of Materials Processing Technology, 2024, 324: 118249.
[5] Gan Wei, Wagoner R H.Die design method for sheet springback[J]. International Journal of Mechanical Sciences, 2004, 46(7): 1097-1113.
[6] 崔晓辉, 周向龙, 杜志浩, 等. 电磁脉冲成形技术新进展及其在飞机蒙皮件制造中的应用[J]. 航空制造技术, 2020, 63(3): 22-32.
Cui Xiaohui, Zhou Xianglong, Du Zhihao, et al.New development of electromagnetic pulse forming technology and its application in aircraft skin parts manufacturing[J]. Aeronautical Manufacturing Tech- nology, 2020, 63(3): 22-32.
[7] 邱立, 李彦涛, 苏攀, 等. 电磁成形中电磁技术问题研究进展[J]. 电工技术学报, 2019, 34(11): 2247-2259.
Qiu Li, Li Yantao, Su Pan, et al.Research on electromagnetic problems in electromagnetic forming process[J]. Transactions of China Electrotechnical Society, 2019, 34(11): 2247-2259.
[8] Liu Wei, Zhang Min, Li Jiaqi, et al.Formability of SS304 stainless steel foil at elevated strain-rate[J]. Journal of Materials Research and Technology, 2023, 26: 7471-7482.
[9] Lin Yuhong, Cui Xiaohui, Chen Kanghua, et al.Forming limit and mechanical properties of 2024-O aluminum alloy under electromagnetic forming[J]. Metals and Materials International, 2022, 28(10): 2472-2482.
[10] Cui Xiaohui, Zhang Zhiwu, Du Zhihao, et al.Inverse bending and springback-control using magnetic pulse forming[J]. Journal of Materials Processing Tech- nology, 2020, 275: 116374.
[11] Psyk V, Risch D, Kinsey B L, et al.Electromagnetic forming: a review[J]. Journal of Materials Processing Technology, 2011, 211(5): 787-829.
[12] 邵子豪, 吴伟业, 汪晨鑫, 等. 基于双层凹型集磁器的管件电磁胀形电磁力特性及变形行为研究[J]. 电工技术学报, 2024, 39(5): 1245-1255.
Shao Zihao, Wu Weiye, Wang Chenxin, et al.Elec- tromagnetic force and formability analysis of tube electromagnetic bulging based on double-layer concave magnetic field shaper[J]. Transactions of China Electrotechnical Society, 2024, 39(5): 1245-1255.
[13] Huang Lantao, Feng Wenjing, Zeng Jin, et al.Research on the drive electromagnetic forming of aluminum alloy and parameter optimization[J]. The International Journal of Advanced Manufacturing Technology, 2022, 120(11): 7101-7113.
[14] Li Fenqiang, Mo Jianhua, Li Jianjun, et al.Forma- bility of Ti-6Al-4V titanium alloy sheet in magnetic pulse bulging[J]. Materials & Design (1980-2015), 2013, 52: 337-344.
[15] Park H, Kim D, Lee J, et al.Effect of an aluminum driver sheet on the electromagnetic forming of DP780 steel sheet[J]. Journal of Materials Processing Tech- nology, 2016, 235: 158-170.
[16] Xu Junrui, Xie Xueyun, Wen Zhisheng, et al.Deformation behaviour of AZ31 magnesium alloy sheet hybrid actuating with Al driver sheet and temperature in magnetic pulse forming[J]. Journal of Manufacturing Processes, 2019, 37: 402-412.
[17] Huang Lantao, Ding Zinan, Zhou Yihan, et al.Effect of the radial dimension of the driver sheet on the electromagnetic driven forming[J]. IEEE Access, 2020, 8: 133503-133513.
[18] Gies S, Weddeling C, Tekkaya A E.Experimental investigations on the optimum driver configuration for electromagnetic sheet metal forming[C]//The 6th International Conference on High Speed Forming, Daejeon, Korea, 2014: 315-324.
[19] Liu Ning, Lai Zhipeng, Cao Quanliang, et al.Effects of the inner/outer diameters of flat spiral coils on electromagnetic sheet metal formation[J]. The Inter- national Journal of Advanced Manufacturing Tech- nology, 2020, 109(5): 1541-1551.
[20] 李梦瑶,邱立,易宁轩,等.基于驱动导体环的板件电磁成形电磁力分布与成形效果研究[J].电工技术学报, 2025, 40(1):13-24.
Li Mengyao, Qiu Li, Yi Ningxuan, et al.Study on electromagnetic force distribution and forming effect of plate electromagnetic forming based on driving conductor ring[J]. Transactions of China Electro- technical Society, 2025, 40(1): 13-24.
[21] 熊奇, 朱鑫辉, 赵翔, 等. AZ31镁合金管件电磁吸引式成形动态特性研究[J]. 电工技术学报, 2023, 38(10): 2577-2588, 2636.
Xiong Qi, Zhu Xinhui, Zhao Xiang, et al.Research of dynamic characteristics in electromagnetic attraction forming of AZ31 magnesium alloy tube[J]. Transa- ctions of China Electrotechnical Society, 2023, 38(10): 2577-2588, 2636.
[22] Cao Quanliang, Han Xiaotao, Lai Zhipeng, et al.Analysis and reduction of coil temperature rise in electromagnetic forming[J]. Journal of Materials Processing Technology, 2015, 225: 185-194.
[23] Liu Wei, Wu Jinjie, Liu Jili, et al.Comparison of electromagnetic-driven stamping and electromagnetic forming limit curves for AA5182-O aluminum alloy sheet[J]. The International Journal of Advanced Manufacturing Technology, 2023, 126(5): 2567-2577.
[24] Ouyang Shaowei, Wang Chen, Li Changxing, et al.Improving the uniformity and controllability of tube deformation via a three-coil forming system[J]. The International Journal of Advanced Manufacturing Technology, 2021, 114(5): 1533-1544.