直流应力下主动式微粒抑制方法的动态配合研究

doi:10.19595/j.cnki.1000-6753.tces.220453

摘要
图/表
参考文献
相关文章 (2)

全文: PDF (1263 KB)
输出: BibTeX | EndNote (RIS)

摘要

直流气体绝缘输电线路（GIL）中自由金属微粒的活性较之交流GIL中更为活跃,对直流GIL的技术发展以及应用带来了严峻的挑战。目前,将各种抑制微粒手段进行主动式动态配合设计是未来发展的趋势。本文搭建直流GIL金属微粒主动式抑制的动态配合的实验平台,并结合有限元仿真,从陷阱捕获率的角度优化了驱赶电极与陷阱间的位置配合;同时提出直流老练优化程序,最终获得主动式微粒抑制的动态配合有效方案。研究结果表明,当驱赶电极与陷阱间的距离为18 mm时,陷阱捕获率可高达70 %;该文优化后的直流老练程序较传统程序可使陷阱捕获性能提升50 %以上;最后通过实验验证了驱赶电极的有效性,且通过大量实验发现高压电极布置驱赶电极后,陷阱捕获率可提高50 %以上。因此,该文结果对提升直流GIL抑制金属微粒的能力具有一定的参考价值。

	服务

	把本文推荐给朋友
	加入我的书架
	加入引用管理器
	E-mail Alert
	RSS
	作者相关文章
	王健
	平安
	常亚楠
	胡智莹
	李庆民

关键词 ：直流气体绝缘输电线路（GIL）, 金属微粒抑制, 驱赶电极, 微粒陷阱, 直流老练程序, 动态配合

Abstract：

Free metal particles are more active in DC gasinsulated transmission lines (GIL) than in AC GIL, posing a serious challenge to the technical development and application of DC GIL. At present, active dynamic coordination of various particle suppression methods is the future trend.
In order to further improve the effectiveness of metal particle suppression in DC GIL, firstly, a simulation model of the cooperation between the driving electrode and the particle trap is established and the position cooperation effect between the driving electrode and the trap is optimized. When the high voltage electrode is arranged with a driving electrode, it significantly reduces the lift-off voltage of the metal particles while blocking the movement of the particles in two ways: (1) When the particles collide with the driving electrode, the particles have difficulty in overcoming shear deformation and friction energy on the tangential side due to the steepness of the driving electrode's circular surface; (2) The existence of an axial electric field on the sloping surface of the driving electrode causes the particles to be subjected to an electric field force in the opposite direction to the axial movement. Therefore, the particles are repelled and blocked by the driving electrode, and have a probability to bounce in the opposite direction on the axis towards the trap area. The simulation model uses the gas insulated equipment field strength design reference E₀ and the trap capture rate as boundary condition and objective function respectively, and obtains the best capture efficiency of 70 % when the position between the driving electrode and the trap is 18 mm. Secondly, the DC withstand voltage test has a special role in detecting certain local defects in the insulation compared to the AC withstand voltage test, and particles in DC equipment can easily penetrate the air gap and collide with the high voltage electrode to cause a discharge breakdown accident. Therefore, for DC GIS/GIL equipment, an optimized design of the DC ripening program, as shown in Fig.A1, has been developed to enable dynamic coordination measures achieve dynamic coordination measures with the driving electrodes and particle traps to suppress metal particles more effectively.

Finally, observation tests of particle motion with the cooperation of the driving electrodes, the traps and DC ripening program were carried out. The reliability of the simulation optimization results was verified. Extensive experiments have shown that the trap capture rate can be increased by more than 50 % after the high electrode placement of the driving electrode, that is, the driving electrode can effectively block the movement direction of the metal particles, so that they can be driven into the trap area to improve the trap capture efficiency for particles. Therefore, the results can further improve the ability of equipment to suppress metal particles, which is of great significance to improve the safety and reliability of DC GIL operation.

Key words： DC gas insulated metal enclosed transmission line (GIL) metal particle suppression driving electrode particle trap DC sophisticated program dynamic coordination

收稿日期: 2022-03-27

PACS:

TM85

基金资助:

国家自然科学基金（52177140）和北京市自然科学基金（L201018）资助项目

通讯作者: 王健 1985年生,副教授,博士生导师,研究方向为直流装备绝缘、先进绝缘材料。E-mail: wangjian31791@ncepu.edu.cn

作者简介: 李庆民男,1968年生,教授,博士生导师,主要从事高电压与绝缘技术、放电物理等领域的研究工作。E-mail: lqmeee@ncepu.edu.cn

引用本文:

王健, 平安, 常亚楠, 胡智莹, 李庆民. 直流应力下主动式微粒抑制方法的动态配合研究[J]. 电工技术学报, 0, (): 4-4. Wang Jian, Ping An, Chang Yanan, Hu Zhiying, Li Qingmin. Research on Dynamic Coordination of Active Particles Suppression Methods under DC Stress. Transactions of China Electrotechnical Society, 0, (): 4-4.

链接本文:

https://dgjsxb.ces-transaction.com/CN/10.19595/j.cnki.1000-6753.tces.220453 https://dgjsxb.ces-transaction.com/CN/Y0/V/I/4

[1] 汤广福, 庞辉, 贺之渊. 先进交直流输电技术在中国的发展与应用[J]. 中国电机工程学报, 2016, 36(7): 1760-1771.
Tang Guangfu, Pang Hui, He Zhiyuan.R & D and application of advanced power transmission tech-nology in China[J]. Proceedings of the CSEE, 2016, 36(7): 1760-1771.
[2] 高克利, 颜湘莲, 刘焱, 等. 环保气体绝缘管道技术研究进展[J]. 电工技术学报, 2020, 35(1): 3-20.
Gao Keli, Yan Xianglian, Liu Yan, et al.Progress of technology for environment-friendly gas insulated transmission line[J]. Transactions of China Electro-technical Society, 2020, 35(1): 3-20.
[3] 王健, 李庆民, 李伯涛, 等. 直流应力下电极表面覆膜对金属微粒启举的影响机理研究[J]. 电工技术学报, 2015, 30(5): 119-127.
Wang Jian, Li Qingmin, Li Botao, et al.Mechanism analysis of the electrode-coating’s impact on the particle-lifting under DC voltage[J]. Transactions of China Electrotechnical Society, 2015, 30(5): 119-127.
[4] Hara M, Maeda Y, Nakagawa N, et al.DC breakdown voltage characteristics of saturated liquid helium in the presence of metallic particles[J]. IEEE Transa-ctions on Dielectrics and Electrical Insulation, 2006, 13(3): 470-476.
[5] 张连根, 路士杰, 李成榕, 等. GIS中线形和球形金属微粒的运动行为和危害性[J]. 电工技术学报, 2019, 34(20): 4217-4225.
Zhang Liangen, Lu Shijie, Li Chengrong, et al.Motor behavior and hazard of spherical and linear particle in gas insulated switchgear[J]. Transactions of China Electrotechnical Society, 2019, 34(20): 4217-4225.
[6] 张博雅, 张贵新. 直流GIL中固-气界面电荷特性研究综述Ⅱ: 电荷调控及抑制策略[J]. 电工技术学报, 2018, 33(22): 5145-5158.
Zhang Boya, Zhang Guixin.Review of charge accumulation characteristics at gas-solid interface in DC GIL, part Ⅱ: charge control and suppression strategy[J]. Transactions of China Electrotechnical Society, 2018, 33(22): 5145-5158.
[7] Iwabuchi H, Matsuoka S, Kumada A, et al.Influence of tiny metal particles on charge accumulation phenomena of GIS model spacer in high-pressure SF6 gas[J]. IEEE Transactions on Dielectrics and Elec-trical Insulation, 2013, 20(5): 1895-1901.
[8] Wang Jian, Hu Qi, Chang Yanan, et al.Metal particle contamination in gas-insulated switchgears/gas-insulated transmission lines[J]. CSEE Journal of Power and Energy Systems, 2019, 7(5): 1011-1025.
[9] Sarathi R, Giridhar A V, Mani A, et al.Investigation of partial discharge activity of conducting particles in liquid nitrogen under DC voltages using UHF technique[J]. IEEE Transactions on Dielectrics and Electrical Insulation, 2008, 15(3): 655-662.
[10] 汪佛池, 杨磊, 曹东亮, 等. 直流GIL中球状自由导电微粒的运动及陷阱抑制[J]. 高电压技术, 2018, 44(10): 3141-3149.
Wang Fochi, Yang Lei, Cao Dongliang, et al.Motion and trap suppression of spherical free conducting particles in DC GIL[J]. High Voltage Engineering, 2018, 44(10): 3141-3149.
[11] 王健, 常亚楠, 王靖瑞, 等. 基于捕捉效用分析的直流GIL微粒陷阱设计与参数优化[J]. 中国电机工程学报, 2020, 40(15): 5050-5061.
Wang Jian, Chang Yanan, Wang Jingrui, et al.Design and optimization of particle traps in DC GIL based on the capture effect analysis[J]. Proceedings of the CSEE, 2020, 40(15): 5050-5061.
[12] Dale S J, Hopkins M D. Methods of particle control in SF₆ insulated CGIT systems[J]. IEEE Transactions on Power Apparatus and Systems, 1982, PAS-101(6): 1654-1663.
[13] 李庆民, 常亚楠, 王健, 等. 气体绝缘输电管道微粒陷阱设计技术研究进展[J]. 高电压技术, 2020, 46(12): 4182-4193.
Li Qingmin, Chang Yanan, Wang Jian, et al.Metho-dological advances of metal particle traps design in gas insulated transmission lines[J]. High Voltage Engineering, 2020, 46(12): 4182-4193.
[14] 汤浩, 吴广宁, 范建斌, 等. 直流气体绝缘输电线路的绝缘设计[J]. 电网技术, 2008, 32(6): 65-70.
Tang Hao, Wu Guangning, Fan Jianbin, et al.Insu-lation design of gas insulated HVDC transmission line[J]. Power System Technology, 2008, 32(6): 65-70.
[15] Hasegawa T, Yamaji K, Hatano M, et al.Develop-ment of insulation structure and enhancement of insulation reliability of 500kV DC GIS[J]. IEEE Transactions on Power Delivery, 1997, 12(1): 194-202.
[16] 范建斌, 李鹏, 李金忠, 等. ±800kV特高压直流GIL关键技术研究[J]. 中国电机工程学报, 2008, 28(13): 1-7.
Fan Jianbin, Li Peng, Li Jinzhong, et al.Study on key technology of ±800kV UHVDC GIL[J]. Proceedings of the CSEE, 2008, 28(13): 1-7.
[17] 刘泽洪, 韩先才, 黄强, 等. 长距离、大容量特高压GIL现场交流耐压试验技术[J]. 高电压技术, 2020, 46(12): 4172-4181.
Liu Zehong, Han Xiancai, Huang Qiang, et al.Field AC withstand voltage test technology of long distance and large capacity UHV GIL[J]. High Voltage Engineering, 2020, 46(12): 4172-4181.
[18] 鲁加明, 曹伟伟, 周振华. 550kV GIL母线的结构设计[J]. 电气技术, 2015, 16(9): 59-63.
Lu Jiaming, Cao Weiwei, Zhou Zhenhua.The structural design of 550kV GIL bus[J]. Electrical Engineering, 2015, 16(9): 59-63.
[19] 黎斌. SF6高压电器设计[M]. 4版. 北京: 机械工业出版社, 2015.
[20] 孙秋芹, 罗宸江, 王峰, 等. 直流GIL导体表面金属颗粒跳跃运动特性研究[J]. 电工技术学报, 2018, 33(22): 5206-5216.
Sun Qiuqin, Luo Chenjiang, Wang Feng, et al.Jumping characteristics of metal particle on the surface of DC gas insulated transmission line conductor[J]. Transactions of China Electrotechnical Society, 2018, 33(22): 5206-5216.
[21] 吕中杰, 黄风雷. 圆板非弹性冲击过程的碰撞恢复系数[J]. 北京理工大学学报, 2008, 28(4): 283-286.
Lü Zhongjie, Huang Fenglei.Coefficient of resti-tution of a circular plate during inelastic collision[J]. Transactions of Beijing Institute of Technology, 2008, 28(4): 283-286.
[22] Hara M.Particle-triggered breakdown mechanism in the presence of DC and AC electrical gradient forces in atmospheric air[C]//11th International Symposium on High-Voltage Engineering (ISH 99), London, UK, 1999: 47-50.
[23] 贾江波, 陶风波, 杨兰均, 等. GIS中不均匀直流电场下球状自由导电微粒运动分析[J]. 中国电机工程学报, 2006, 26(8): 106-111.
Jia Jiangbo, Tao Fengbo, Yang Lanjun, et al.Motion analysis of spherical free conducting particle in non-uniform electric field of GIS under DC voltage[J]. Proceedings of the CSEE, 2006, 26(8): 106-111.
[24] 国家能源局. DL/T 304-2011 气体绝缘金属封闭输电线路现场交接试验导则[S]. 北京: 中国电力出版社, 2011.