Abstract：With the widespread application of power electronics technology in modern variable-frequency drive systems, bearing electrical erosion damage caused by motor bearing voltage and bearing current induced by frequency converters has become one of the primary causes of bearing failure. Currently, the assessment of bearing electrical erosion severity still heavily relies on vibration data. However, the correlation between vibration data and the extent of electrical erosion damage is weak, often requiring the presence of significant damage such as grooves on the bearing for effective detection, making early warning challenging. In contrast, electrical characteristic parameters such as bearing impedance, breakdown voltage threshold, and breakdown resistance can directly reflect the internal insulation condition and electrical performance of the bearing, exhibiting high sensitivity to micro-level changes such as lubricant degradation, oil film thinning, and initial-stage electrical erosion. Nevertheless, current research on bearing electrical characteristics remains in its preliminary stages, and the variation patterns of these parameters have yet to be systematically analyzed. This study established an experimental platform for measuring the electrical characteristics of rolling bearings. The variations in electrical characteristics of two SKF 6007-2Z grease-lubricated bearings under different operating parameters, including voltage amplitude, power frequency, rotational speed, and temperature, were measured, and the underlying causes were analyzed. The research findings are as follows: In terms of steady-state electrical characteristics, when the bearing voltage is below the breakdown voltage threshold, voltage variations have a minimal effect on bearing impedance. At low speeds, the lubricating oil film is thin, resulting in lower impedance amplitude. As the rotational speed increases, the oil film thickness increases and stabilizes, leading to a corresponding rise in impedance which gradually plateaus. At high speeds, impedance slightly decreases due to the weakening effect of shear forces on the oil film. An increase in temperature reduces grease viscosity and thins the oil film, resulting in lower impedance and potentially triggering breakdown discharge under low-speed conditions. Regarding dynamic electrical characteristics, the breakdown voltage threshold increases with higher rotational speed and decreases with rising temperature. An increase in bearing voltage intensifies the local ionization of the lubricating grease, leading to a reduction in breakdown resistance. At low rotational speeds, the oil film is thin and unevenly distributed, with weaker insulating properties, resulting in lower breakdown resistance. As rotational speed increases, a stable lubricating oil film forms, leading to higher breakdown resistance. When rotational speed increases further, frictional heating may cause localized temperature rise in the oil film, reducing viscosity and thinning the film, which results in a slight decrease in breakdown resistance. For a single bearing, the influence of power frequency on its breakdown resistance is negligible. When the bearing voltage exceeds the oil film breakdown voltage threshold, higher operating temperatures prolong the time the bearing remains in a resistive state, impairing its ability to recover capacitance. In summary, when the oil film is well-established, an increase in temperature increases the risk of electrical erosion of the bearing. This study systematically reveals the influence patterns of operating parameters on bearing impedance, laying a theoretical foundation for constructing electrical characteristic-based diagnostic and predictive methods for electrical erosion faults in grease-lubricated bearings.
张殿海, 迟连强, 赵俊清, 刘禹彤, 任自艳. 模拟服役条件下脂润滑滚动轴承电特性变化规律研究[J]. 电工技术学报, 2026, 41(7): 2181-2190.
Zhang Dianhai, Chi Lianqiang, Zhao Junqing, Liu Yutong, Ren Ziyan. Investigation on the Variation Patterns of Electrical Characteristics in Grease-Lubricated Rolling Bearings under Simulated Service Conditions. Transactions of China Electrotechnical Society, 2026, 41(7): 2181-2190.
[1] 马伟明, 王东, 程思为, 等. 高性能电机系统的共性基础科学问题与技术发展前沿[J]. 中国电机工程学报, 2016, 36(8): 2025-2035. Ma Weiming, Wang Dong, Cheng Siwei, et al.Common basic scientific problems and development of leading-edge technology of high performancemotor system[J]. Proceedings of the CSEE, 2016, 36(8): 2025-2035. [2] 肖宗鑫, 胡明辉, 周强, 等. 电驱系统轴承电蚀抑制措施研究综述[J]. 电工技术学报, 2025, 40(20): 6552-6576. Xiao Zongxin, Hu Minghui, Zhou Qiang, et al.A review of research on bearing electrical-erosion suppression measures in electric drive systems[J]. Transactions of China Electrotechnical Society, 2025, 40(20): 6552-6576. [3] Xiao Zongxin, Hu Minghui, Chen Shuang, et al.Bearing electrical-erosion damage in electrical drive systems: a review[J]. IEEE Transactions on Trans-portation Electrification, 2024, 10(2): 3428-3442. [4] Tawfiq K B, Güleç M, Sergeant P.Bearing current and shaft voltage in electrical machines: a comprehensive research review[J]. Machines, 2023, 11(5): 550. [5] 杨明亮, 程远, 杜博超, 等. 基于共模变压器原理的电机轴承电腐蚀非接触式主动抑制方法[J/OL]. 电工技术学报, 2025: 1-18[2025-12-14]. https://doi.org/10.19595/j.cnki.1000-6753.tces.251062. Yang Mingliang, Cheng Yuan, Du Bochao, et al. A non-contact active suppression method for motor bearingelectrical erosion based on the principle of common-mode transformer[J/OL]. Transactions of China Electrotechnical Society, 2025: 1-18[2025-12-14]. https://doi.org/10.19595/j.cnki.1000-6753.tces.251062. [6] Chen Shaotang, Lipo T A, Fitzgerald D.Source of induction motor bearing currents caused by PWM inverters[J]. IEEE Transactions on Energy Conversion, 1996, 11(1): 25-32. [7] Chen Shaotang, Lipo T A, Fitzgerald D.Modeling of motor bearing currents in PWM inverter drives[J]. IEEE Transactions on Industry Applications, 1996, 32(6): 1365-1370. [8] 迟连强, 张殿海, 赵俊清, 等. 旋转电机轴承电蚀损伤机理与缓解措施研究进展[J]. 电工技术学报, 2024, 39(20): 6409-6430. Chi Lianqiang, Zhang Dianhai, Zhao Junqing, et al.Research progress on the mechanism and mitigation measure of electrical corrosion damage in rotating motor bearings[J]. Transactions of China Electro-technical Society, 2024, 39(20): 6409-6430. [9] Muetze A, Binder A.Practical rules for assessment of inverter-induced bearing currents in inverter-fed AC motors up to 500 kW[J]. IEEE Transactions on Industrial Electronics, 2007, 54(3): 1614-1622. [10] 郝雅丽, 刘瑞芳, 陈立珂, 等. 一种电动汽车电机容性和感性轴电流的综合建模方法[J/OL]. 电工技术学报, 2025: 1-12[2025-12-14]. http://doi.org/10.19595/j.cnki.1000-6753.tces.251129. Hao Yali, Liu Ruifang, Chen Like, et al. A comprehensive modeling method of capacitive and inductive bearing currents in electric vehicle motors [J/OL]. Transactions of China Electrotechnical Society, 2025: 1-12[2025-12-14]. http://doi.org/10.19595/j.cnki.1000-6753.tces.251129. [11] Êvo M T A, Alzamora A M, Zaparoli I O, et al. Inverter-induced bearing currents: a thorough study of the cause-and-effect chains[J]. IEEE Industry Appli-cations Magazine, 2023, 29(3): 57-66. [12] Liu W.The prevalent motor bearing premature failures due to the high frequency electric current passage[J]. Engineering Failure Analysis, 2014, 45: 118-127. [13] 郑丹, 温旭辉, 范涛, 等. 高环境温度高功率密度SiC电机驱动控制器设计与实现[J]. 电工技术学报, 2025, 40(15): 4889-4904. Zheng Dan, Wen Xuhui, Fan Tao, et al.Design and implementation of SiC motor drive controller with high environmental temperature and high power density[J]. Transactions of China Electrotechnical Society, 2025, 40(15): 4889-4904. [14] Singleton R K, Strangas E G, Aviyente S.Extended Kalman filtering for remaining usefullife estimation of bearings[J]. IEEE Transactions on Industrial Electronics, 2015, 62(3): 1781-1790. [15] Singleton R K, Strangas E G, Aviyente S.The use of bearing currents and vibrations in lifetime estimation of bearings[J]. IEEE Transactions on Industrial Infor-matics, 2017, 13(3): 1301-1309. [16] Kumar A, Parkash C, Zhou Yuqing, et al.Entropy-based domain adaption strategy for predicting remaining useful life of rolling element bearing[J]. Engineering Applications of Artificial Intelligence, 2024, 133: 108575. [17] Qian Yuning, Yan Ruqiang.Remaining useful life prediction of rolling bearingsusing an enhanced particle filter[J]. IEEE Transactions on Instrumentation and Measurement, 2015, 64(10): 2696-2707. [18] Niskanen V, Muetze A, Ahola J.Study on bearing impedance properties at several hundred kilohertz for different electric machine operating parameters[J]. IEEE Transactions on Industry Applications, 2014, 50(5): 3438-3447. [19] De Gaetano D, Zhu Wenjun, Sun Xiangyu, et al.Experimental ball bearing impedance analysis under different speed and electrical conditions[J]. IEEE Transactions on Dielectrics and Electrical Insulation, 2023, 30(3): 1312-1321. [20] 刘瑞芳, 娄卓夫, 马喜平, 等. 电机轴电流问题中轴承等效电容和电阻的计算模型[J]. 中国电机工程学报, 2014, 34(15): 2430-2437. Liu Ruifang, Lou Zhuofu, Ma Xiping, et al.Modelingof bearing capacitance and resistance in motor bearing current problem[J]. Proceedings of the CSEE, 2014, 34(15): 2430-2437. [21] Magdun O, Binder A.Calculation of roller and ball bearing capacitances and prediction of EDM currents[C]//2009 35th Annual Conference of IEEE Industrial Electronics, Porto, Portugal, 2009: 1051-1056. [22] 任雪娇,刘瑞芳,王芹芹. 轴电流问题中轴承模型的探究及等效电阻计算[J]. 电气工程学报, 2019, 14(2): 1-6. Ren Xuejiao, Liu Ruifang, WangQinqin. Research on bearing model of bearing current analysis and calculation of equivalent resistance[J]. Journal of Electrical Engineering, 2019, 14(2): 1-6. [23] Ren Xuejiao, Liu Ruifang, Yang Erle.Modelling of the bearing breakdown resistance in bearing currents problem of AC motors[J]. Energies, 2019, 12(6): 1121. [24] Muetze A, Binder A.Techniques for measurement of parameters related to inverter-induced bearing currents[J]. IEEE Transactions on Industry Applications, 2007, 43(5): 1274-1283. [25] 牛凯. 轴承交流电击穿特性与表面电损伤机理研究[D]. 洛阳: 河南科技大学, 2023. Niu Kai.Study on AC breakdown characteristics and surface electric damage mechanism of bearings[D]. Luoyang: Henan University of Science and Technology, 2023.
2026, Vol. 41 
